Multi Source Translation Content

cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

Multi Source Translation Content

Discussions

Sort by:
Question about GCM IV Length Support in HSE FW 2.40.0 and 2.55.0 Hello, I have a question regarding the GCM operation of the HSE on the S32K358. In the AEAD service description of the HSE Service API Reference Manual, both HSE FW 2.40.0 and 2.55.0 specify the following for GCM: GCM: 1 <= ivLength <= 2^32-1. Recommended 12 bytes or greater. However, the HSE FW 2.40.0 manual contains the following additional note, which is not present in the HSE FW 2.55.0 manual: In GCM operations, it is recommended to use IV values of exactly 12 bytes. For any IV size different from 12 bytes, the authentication tag generated by the GCM encryption operation might not be correct. In GCM decryption operations, the authentication check might fail. In this regard, I would like to clarify the following: 1. Can GCM operations be used normally in HSE FW 2.40.0 when the IV length is not 12 bytes? 2. Is there any behavioral difference in GCM operations between HSE FW 2.40.0 and 2.55.0 when using an IV length other than 12 bytes? 3. Is there any difference in the reliability of GCM operations between HSE FW 2.40.0 and 2.55.0 when using an IV length other than 12 bytes? In our tests, GCM encryption and decryption were performed successfully even when the IV length was not 12 bytes, and the authentication results were also correct. Therefore, I would like to confirm whether using an IV length other than 12 bytes is fully supported in HSE FW 2.40.0, and whether there is any functional difference compared to using HSE FW 2.55.0 in this case. Thank you for your clarification. Re: Question about GCM IV Length Support in HSE FW 2.40.0 and 2.55.0 Hi @wodudwo  Technically, ivLength can be configured with a different length; however, doing so is not recommended because the behavior is not guaranteed to be reliable. As you correctly pointed out, the documentation states that for GCM decryption operations, the authentication check may fail when IV lengths other than 12 bytes are used. While your test may have passed using a different IV length, this does not guarantee that the operation will always succeed. In other words, a successful result in a particular test case should not be interpreted as an indication that the configuration is fully supported or will work consistently in all scenarios.  Additionally, if you review the release notes for both firmware versions, you will find that the List of Limitations includes the same recommendation: use IV values of exactly 12 bytes. Although the note was removed from the HSE Service API Reference Manual starting with HSE FW 2.55.0, the limitation itself remains unchanged.  BR, VaneB Re: Question about GCM IV Length Support in HSE FW 2.40.0 and 2.55.0 Hi, Thank you for the clarification. I have one additional question regarding the use of an IV other than 12 bytes. I understand that the authentication tag generation/verification may not be reliable when a non-12-byte IV is used. In this case, can the encryption/decryption operation itself be considered reliable, regardless of the authentication tag? For example, if a 16-byte IV is used for GCM encryption, is the resulting ciphertext guaranteed to be correct and consistent, even though the authentication tag may not be reliable? In other words, is the limitation specific to the authentication tag generation/verification, or does using an IV other than 12 bytes also affect the reliability/correctness of the actual encryption/decryption operation? Thank you. Re: Question about GCM IV Length Support in HSE FW 2.40.0 and 2.55.0 Hi @wodudwo  As stated in the HSE Service API Reference Manual, the recommended IV length is within the range 1<= ivLength <= 2∧32-1 with 12 bytes or greater recommended. Reference implementations are available in hse_crypto.c (S32K3 General Purpose HSE Demo Examples) and hse_sessionkeys_example.c (HSE DemoApp). Re: Question about GCM IV Length Support in HSE FW 2.40.0 and 2.55.0 Hi, thank you for your response. However, I would like to clarify one specific point that was not addressed in my previous question. If a non-12-byte IV, such as a 16-byte IV, is used for GCM: 1. Is the ciphertext generated by the encryption operation guaranteed to be correct and reliable? 2. Is the plaintext recovered by the decryption operation guaranteed to be correct and reliable? I understand that the authentication tag generation/verification may not be reliable with a non-12-byte IV. My question is whether this limitation also applies to the actual encryption/decryption result (ciphertext/plaintext), or whether the limitation is only related to the authentication tag. Could you please clarify this point specifically?
View full article
Security-updated prebuilts for Android Automotive 16.0.0_1.3.0 without breaking kernel/U-Boot builds Hi, we are using NXP Android Automotive 16.0.0_1.3.0 with kernel 6.12 and the prebuilt revisions documented by NXP: platform/prebuilts/clang/host/linux-x86 66acdd82ee62e4aaa4248f03191c59dfed9db193 kernel/prebuilts/build-tools 3c5e4f14b451ec85167c38b917d2459687abd7f4 platform/prebuilts/rust 5156e7f81ae254c79ee736e44c960e75ad685c67 platform/prebuilts/clang-tools 17329f6590e2872dcf04a0c96a176be089470cd9 These are the revisions listed in the NXP Android Automotive User's Guide for this release. The build works with these revisions, but our container vulnerability scan reports several HIGH and CRITICAL findings inside the supplied Android prebuilts. For example, the Clang prebuilts contain embedded Go standard libraries. For clang-r536225/bin/clang, the scan reports: Total: 22 HIGH: 21 CRITICAL: 1 Go stdlib version: v1.23.2 Example: CVE-2025-68121 crypto/tls - incorrect certificate validation The same finding pattern also appears in clang++ and clang-tidy, and in the newer clang-r547379 binaries where the embedded Go version is v1.23.4. The NXP-pinned kernel/prebuilts/build-tools also contains affected soong_zip binaries with the same Go-stdlib finding pattern. The Rust prebuilts also contain findings in shipped Cargo lock files, for example: thin-vec 0.2.13 CVE-2026-6654 fixed in 0.2.16 hashbrown 0.15.0 GHSA-wwq9-3cpr-mm53 fixed in 0.15.1 We do not want to replace the documented revisions with arbitrary newer AOSP commits, because these prebuilts are part of the NXP kernel/U-Boot build environment and we want to preserve compatibility with Android Automotive 16.0.0_1.3.0 / kernel 6.12. Are there newer NXP-recommended or known-compatible commit IDs for these prebuilts? In particular, we are looking for updated revisions for: platform/prebuilts/clang/host/linux-x86 kernel/prebuilts/build-tools platform/prebuilts/rust platform/prebuilts/clang-tools   Has NXP, or anyone in the community, already updated these revisions and verified that the following still work? Ideally, we would also like confirmation that a complete Android Automotive build still works with the updated prebuilts. We would prefer to update the affected prebuilts instead of permanently suppressing the security findings. I have attached the failed vulnerability scan log for reference. It contains the complete findings for the affected Clang, kernel build-tools and Rust prebuilts, including detected embedded versions and available fixed versions. Thanks. Android Re: Security-updated prebuilts for Android Automotive 16.0.0_1.3.0 without breaking kernel/U-Boot bu Hello, I'm reviewing your issue, I'll keep you updated.  Regards. Re: Security-updated prebuilts for Android Automotive 16.0.0_1.3.0 without breaking kernel/U-Boot bu Hello,  Internal team has shared below reply.   We have not any newer recommended/know-compatible commit IDs for  platform/prebuilts/clang/host/linux-x86 kernel/prebuilts/build-tools platform/prebuilts/rust platform/prebuilts/clang-tools and for Android 16.0 automotive 1.3.0 release version.   Android 16.0 automotive 1.3.0 has been released on May-21 2026, since then there have been no updates for this release. We do not update Android automotive releases; we are working on the next Android automotive release => Android 16.0 automotive 2.1.0 based on Linux kernel 6.18.y & with updated Linux kernel build tools. External release date of AA16.0 2.1.0 is on Oct-13 2026.
View full article
question regarding electrical motor control job Okay so i got interviewed for a job which seems veeery interesting, in the field of control of electrical motors. Now the problem is that he basically described 2 main job functions very different: one is actually develope of control system for motors: simulations in matlab, implementation in microcontrollers and testing. The second part however is related to PLC: he told me that they write some function that are somehow integrated into the system they build. Now my question is: how do i know if i end up working in the first branch o the second one? And if both, with which percentage? Do some of u work in a similar company and can tell me how the 2 aspects are balanced? Should i just ask it to the interviewer? Note that they are not 2 different positions Re: question regarding electrical motor control job Hi taotomi urushi,   Thanks for reaching out.   I’m not sure I fully understand your question. Could you please clarify what specific information about NXP products or technologies you are looking for? Please provide more details about your inquiry so that we can better assist you.   Here is our NXP website: https://www.nxp.com/   If your intention is to apply for a position at NXP, please visit our careers page and submit your application through the following link:   https://nxp.wd3.myworkdayjobs.com/careers   Hope all the information could help you.   BR Lina 
View full article
The CSEC and Flash driver in an S32K144 project created with S32DS3.5 cannot coexist. I need to modify an existing S32DS3.5 project to meet the requirements of a new client. Since a Flash driver already exists, I need to add a CSEC driver. When configuring peripherals in the MEX file, I found that adding CSEC results in an error, while deleting CSEC or the Flash driver resolves the issue. How can I resolve this problem? IDE: S32DS3.5 SDK: S32 SDK RTM 4.0.1 err.jpg     Re: S32DS3.5创建的S32K144工程CSEC和Flash驱动不能同时存在 Hello @ZDDL, According to the SDK release notes, it is compatible with S32 Design Studio (S32DS) 3.4. Compatibility with S32DS 3.5 has not been validated, so we cannot guarantee correct functionality. I also strongly recommend installing only one SDK or RTD version within a single IDE installation. If multiple SDK/RTD versions are required, use separate IDE installations for each version. danielmartynek_0-1788953256888.png BR, Daniel 
View full article
S32 デザインスタジオのライセンスが切れました こんにちは、 私のS32デザインスタジオライセンスはもうすぐ期限切れになります。 免許の更新は可能ですか? ライセンスコードは085B-C474-AA78-FC99です。 ご回答をお待ちしています。 Re: s32 design studio license expired こんにちは、 お客様のS32DSライセンスが延長されました。 Re: s32 design studio license expired こんにちは、 今あなたのアカウントを確認したところ、ライセンスは2030年まで有効です。ライセンスが本当に期限切れでないまで待つか、既存のライセンスを返却して古いコードで再度有効化することもできます。 Re: s32 design studio license expired こんにちは、 ssong_0-1789444671642.png まだ延長されていないようです。もう一度確認してもらえますか?ありがとう。 Re: s32 design studio license expired こんにちは、NXPサポートの皆さん。このメッセージがあなたの元に無事届くことを願っています。私のS32DSライセンスが期限切れになり、現在の開発作業が妨げられています。延長を手伝ってもらえますか? 私の認証ID: 406C-B408-57DB-0C62 製品:ARM v2.2用のS32 Design Studio。 ご返信よろしくお願いします。
View full article
S32DS3.6.6にSW32K1_S32M24x_RTD_R21-11_3.0.0_QLP07をインストールした後、K144プロジェクトを作成できません。 S32DS3.6.6をインストールした後、インストール...新規ソフトウェア方式を使用して、SW32K1_S32DS_Development_Pack_3.6.6_RFP_D2602.zip と SW32K1_S32M24x_RTD_R21-11_3.0.0_QLP07_D2606_DesignStudio_updatesite.zip をインストールしました。拡張機能リストには、両方のパッケージが正常にインストールされたと表示されています。しかし、サンプルや新規プロジェクトの作成時に K144 が見つからず、K3 しか利用できません。この問題を解決するにはどうすればよいでしょうか? Ex.jpg exam.jpg     Re: S32DS3.6.6安装SW32K1_S32M24x_RTD_R21-11_3.0.0_QLP07后无法创建K144工程 こんにちは、 @ZDDL さん。 QLP07アップデートサイトは、S32K1/S32M24x RTD 3.0.0用のパッチ/拡張機能のみであり、完全なRTDインストールではありません。 まずベース SW32K1_S32M24x_RTD_R21-11_3.0.0_D2503_DesignStudio_updatesite.zipパッケージをインストールし、その上にQLP07をインストールしてください。S32 Design Studioを再起動すると、S32K144デバイスと対応する例が利用可能になるはずです。 QLP07で導入された追加機能、特にS32K142Nデバイスのサポートが必要ない場合は、QLP07パッケージをインストールする必要はありません。   よろしくお願いいたします。 パベル
View full article
关于电机控制工作的问题 我面试了一份工作,看起来非常有趣,是关于电机控制领域的。现在的问题是,他基本上描述了两个截然不同的主要工作职能:一个是电机控制系统的开发:在 matlab 中进行仿真,在微控制器中实现和测试。但第二部分与 PLC 有关:他告诉我,他们编写了一些函数,这些函数以某种方式集成到他们构建的系统中。现在我的问题是:我如何知道我最终会在第一个分支还是第二个分支工作?如果两者都有,比例是多少?你们当中有人在类似的公司工作吗?能否告诉我这两方面是如何平衡的?我应该直接问面试官吗?请注意,它们并非两种不同的立场。 Re: question regarding electrical motor control job 您好,桃金娘漆,   感谢您的联系。   我不太确定我是否完全理解你的问题。请问您想了解恩智浦半导体产品或技术的哪些具体信息?请提供更多关于您咨询的内容,以便我们更好地为您提供帮助。   这是我们的恩智浦网站: https://www.nxp.com/   如果您有意申请恩智浦的职位,请访问我们的招聘页面,并通过以下链接提交您的申请: https://nxp.wd3.myworkdayjobs.com/careers   希望这些信息对您有所帮助。   BR 莉娜
View full article
Android オートモーティブ 16.0.0_1.3.0向けのセキュリティアップデート済みプリビルドで、カーネルやU-Bootビルドを壊さずに提供されました こんにちは、 NXPの Android オートモーティブ 16.0.0_1.3.0をカーネル6.12 と、NXPが文書化したプリビルドのリビジョンを使用しています。 プラットフォーム/Prebuilts/Clang/Host/Linux-x86 66acdd82ee62e4AAAA4248F03191C59DFED9DB193 カーネル/prebuilts/build-tools 3c5e4f14b451ec85167c38b917d2459687abd7f4 プラットフォーム/prebuilts/rust 5156e7f81ae254c79ee736e44C960e75AD685C67 プラットフォーム/prebuilts/clang-tools 17329f6590e2872dcf04a0c96a176be089470cd9 これらは本リリースのNXP Android Automotiveユーザーガイドに記載された改訂版です。 ビルドはこれらのリビジョンで動作しますが、当社のコンテナ脆弱性スキャンでは、 提供されたAndroidプリビルト内でいくつかのHIGHかつCRITICALな発見が報告されています。 例えば、Clangのプリビルド版にはGoの標準ライブラリが組み込まれています。clang-r536225/bin/clang のスキャン結果は以下のとおりです。 合計: 22 高: 21 重大: 1 Go stdlib バージョン: v1.23.2 例: CVE-2025-68121 crypto/tls - 証明書の検証が正しく行われていない 同様の検出パターンは、clang++ および clang-tidy、そして組み込みの Go バージョンが v1.23.4 である新しい clang-r547379 バイナリでも見られます。 NXPが固定しているkernel/prebuilts/build-toolsにも、同じGo-stdlib検出パターンを持つ、影響を受けるsoong_zipバイナリが含まれています。 Rustのプリビルド版には、出荷されるCargoロックファイルに含まれる発見事項も含まれています。例えば、以下のとおりです。 thin-vec 0.2.13 CVE-2026-6654 は 0.2.16 で修正されました。 hashbrown 0.15.0 GHSA-wwq9-3cpr-mm53 は 0.15.1 で修正されました。 これらのプリビルドはNXPカーネル/U-Bootビルド環境の一部であり、 Android Automotive 16.0.0_1.3.0 / カーネル6.12との互換性を維持したいため、ドキュメント化されたリビジョンを任意の新しいAOSPコミットで置き換えるつもりはありません。 これらのプリビルド製品に対応する、NXPが推奨する、または互換性が確認されている新しいコミットIDはありますか? 特に、以下の項目に関する最新の改訂版を求めています。 platform/prebuilts/clang/host/linux-x86 カーネル/prebuilts/build-tools platform/prebuilts/rust platform/prebuilts/clang-tools   NXP社、あるいはコミュニティの誰かが、これらの改訂版を既に更新し、以下の内容が引き続き正常に動作することを確認しましたか? 理想的には、更新されたプリビルト車と完全なAndroid Automotiveビルドがまだ動作するかどうかの確認も望んでいます。 セキュリティ調査結果を恒久的に抑制するよりも、影響を受けたプリビルトを更新したいと考えています。 参考までに、失敗した脆弱性スキャンログを添付しました。これには、影響を受けるClang、カーネルビルドツール、およびRustのプリビルド版に関する完全な調査結果が含まれており、検出された組み込みバージョンと利用可能な修正バージョンも含まれています。 ありがとうございます。 Android Re: Security-updated prebuilts for Android Automotive 16.0.0_1.3.0 without breaking kernel/U-Boot bu こんにちは、 ご指摘いただいた件について調査中です。進捗状況は随時ご連絡いたします。 よろしくお願いします。 Re: Security-updated prebuilts for Android Automotive 16.0.0_1.3.0 without breaking kernel/U-Boot bu こんにちは、 社内チームから以下の回答が寄せられました。 推奨/互換性のある新しいコミット ID はありません。 プラットフォーム/プリビルト/CLANG/ホスト/Linux-x86 kernel/prebuilts/build-tools プラットフォーム/プレビルド/錆 プラットフォーム/プレビルド/クラングツール そしてAndroid 16.0のオートモーティブ向け1.3.0リリースバージョンです。   Android 16.0 オートモーティブ 1.3.0は2026年5月21日にリリースされましたが、それ以降はアップデートはありません。Androidオートモーティブのアップデートは行っていません。次回のAndroid オートモーティブ リリースに取り組んでいます => Android 16.0 automotive 2.1.0Linuxカーネル6.18.yをベースにし、最新のLinuxカーネルビルドツールを用いています。 AA16.0 2.1.0の外部リリース日は2026年10月13日です。
View full article
S32DS3.6.6安装SW32K1_S32M24x_RTD_R21-11_3.0.0_QLP07后无法创建K144工程 新安装S32DS3.6.6后,通过install New Software的方式分别安装了SW32K1_S32DS_Development_Pack_3.6.6_RFP_D2602.zip和SW32K1_S32M24x_RTD_R21-11_3.0.0_QLP07_D2606_DesignStudio_updatesite.zip。在Extensions里面也可以看到这2个包安装成功,但是无论是通过example还是新建工程都找不到K144只有K3的。怎么处理? Ex.jpg exam.jpg     Re: S32DS3.6.6安装SW32K1_S32M24x_RTD_R21-11_3.0.0_QLP07后无法创建K144工程 你好@ZDDL , QLP07 更新站点只是 S32K1/S32M24x RTD 3.0.0 的一个补丁/扩展程序;它不是一个完整的 RTD 安装。 请先安装基础的SW32K1_S32M24x_RTD_R21-11_3.0.0_D2503_DesignStudio_updatesite.zip软件包,然后再在其上安装 QLP07。重启 S32 Design Studio 后,S32K144 设备和相应的示例应该就可以使用了。 如果您不需要 QLP07 中引入的附加功能,特别是对 S32K142N 设备的支持,则无需安装 QLP07 软件包。   顺祝商祺! 帕维尔
View full article
i.MX8QXP C0: クラッシュ証拠キャプチャ SCwatchdogresetCortex-M4監視A35クラスタ全体にラムーブ こんにちは、NXPチームの皆さん、 プラットフォームの詳細: SoC: i.MX8QXP C0、MEKリファレンスに基づくカスタムボード BSP: NXP Linux 6.6.3 [状態完全タグ、例:lf-6.6.3-1.0.0]、ヨクト・スカースギャップ SCFWバージョン:[scu_rmを実行し、ブートログを確認してバージョンを貼り付けてください] SECO/AHAB: [有効/無効、バージョン] U-Boot: [2024.04/tag] Cortex-M4(CM4_0):現在使用されておらず、ファームウェアはインストールされていません ユースケース:生産オートモーティブ向けインストゥルメントクラスター;A35はLinux/Weston HMIを動作させています 問題提起: 実稼働環境では、A35 複合システムがクラッシュしたり、ハードハングアップ(カーネルパニック/ロックアップ)を起こしたりするケースが時折発生します。現在では持続的なクラッシュの証拠もなく、自律的な復旧もありません。クラスターは手動で電源を入れ直すまで停止状態のままで、フィールドやDVの発生はデバッグできません。我々は、(a) pstore/ramoops を使用したウォッチドッグリセット後のパニックログの永続化、および (b) A35 パーティションのみをリセットできる機能を備えた CM4_0 による A35 の監視を実装したいと考えています。 i.MX8QXP C0において、システムウォッチドッグ(imx-sc-wdt、SCFWによって処理される)が作動した場合、どのようなタイプのリセットが実行されますか?(SoC/ボード全体のリセット、またはAクラスタパーティションのリセット)これはSCFWボードファイルまたはsc_pm API経由で設定可能ですか? Re: i.MX8QXP C0: crashevidence capture ramoops across SCwatchdogresetCortex-M4 supervision A35 clus こんにちは、 はい、SCFWが管理する仮想監視犬を使ってパーティションをリセットすることもできます SC_TIMER_WDOG_ACTION_PARTITION 動作はLinux/A35パーティションのみをリセットします。 また、SCFW sc_pm APIを介してA35パーティション上で sc_pm_reset_partition() を呼び出すことで、CM4_0ファームウェアから直接同じ効果を得る方法もあります。これにより、CM4_0はウォッチドッグメカニズムとは独立した完全な監視制御が可能になります。 この件については、あなたが使っている特定のバージョンのSCFW移植ガイドで詳しく知ることができます。 よろしくお願いいたします。 アルド。
View full article
i.MX8QXP C0: crashevidence capture ramoops across SCwatchdogresetCortex-M4 supervision A35 cluster Hi NXP Team,  Platform details: SoC: i.MX8QXP C0, custom board based on MEK reference BSP: NXP Linux 6.6.3 [state exact tag, e.g. lf-6.6.3-1.0.0], Yocto Scarthgap SCFW version: [run scu_rm / check boot log — paste version] SECO/AHAB: [enabled/not enabled, version] U-Boot: [2024.04/tag] Cortex-M4 (CM4_0): currently unused, no firmware loaded Use case: production automotive instrument cluster; A35 runs Linux/Weston HMI Problem statement: In production we occasionally see the A35 complex crash or hard-hang (kernel panic / lockup). Today we have no persisted crash evidence and no autonomous recovery — the cluster stays dead until a manual power cycle, and field/DV occurrences cannot be debugged. We want to implement (a) panic-log persistence across a watchdog reset using pstore/ramoops, and (b) supervision of the A35 by the CM4_0 with the ability to reset only the A35 partition. On i.MX8QXP C0, when the system watchdog (imx-sc-wdt, handled by SCFW) fires, what type of reset is performed — full SoC/board reset or A-cluster partition reset? Is this configurable via SCFW board file or sc_pm API? Re: i.MX8QXP C0: crashevidence capture ramoops across SCwatchdogresetCortex-M4 supervision A35 clus Hello, yes, you may use a virtual watchdog managed by the SCFW to reset the partition SC_TIMER_WDOG_ACTION_PARTITION behavior is what you want it resets only the Linux/A35 partition. Also, there is a way to achieve the same effect from CM4_0 firmware directly by calling sc_pm_reset_partition() on the A35 partition via the SCFW sc_pm API, which gives the CM4_0 full supervisory control independent of the watchdog mechanism. You can find more information about this on the SCFW porting guide for the specific version that you are using. Best regards/Saludos, Aldo.
View full article
Unable to create K144 project after installing SW32K1_S32M24x_RTD_R21-11_3.0.0_QLP07 on S32DS3.6.6 After installing S32DS3.6.6, via install...I installed SW32K1_S32DS_Development_Pack_3.6.6_RFP_D2602.zip and SW32K1_S32M24x_RTD_R21-11_3.0.0_QLP07_D2606_DesignStudio_updatesite.zip using the New Software method. Both packages are shown as successfully installed in the Extensions list. However, I can't find K144 in the examples or by creating a new project; only K3 is available. How can I fix this? Ex.jpg exam.jpg     Re: S32DS3.6.6安装SW32K1_S32M24x_RTD_R21-11_3.0.0_QLP07后无法创建K144工程 Hello @ZDDL , The QLP07 update site is only a patch/extension for S32K1/S32M24x RTD 3.0.0; it is not a complete RTD installation. Please first install the base SW32K1_S32M24x_RTD_R21-11_3.0.0_D2503_DesignStudio_updatesite.zip package and then install QLP07 on top of it. After restarting S32 Design Studio, the S32K144 device and the corresponding examples should become available. If you do not require the additional functionality introduced in QLP07, specifically support for the S32K142N devices, you do not need to install the QLP07 package.   Best regards, Pavel
View full article
最小配置即可协商更高的 USB 限流 我有一个可以通过USB供电的设备,它搭载了MCXN947处理器。我目前还没有配置USB,只是直接取5V电源。但是,我想提高限流,它的默认值似乎是 100mA。 我只需做哪些最少的配置就能提高限流?我在MCUXpresso配置工具中尝试设置USBFS。它至少需要一个接口,所以我尝试设置DFU模式。大部分东西都编译成功了,但是配置工具生成了一个名为 timer_queue.c 的文件。它定义了一个与 FreeRTOS port.c 冲突的 SysTick_Handler。SysTick_Handler。 1)我还能做些什么来提高限流? 2) 如果设置此 DFU 接口与其他方法一样好,我应该如何解决自动生成的代码和 FreeRTOS 端口之间的冲突? Re: minimal configuration to negotiate higher current limit on USB 你好@robert_hines 是的,USB 设备必须在 USB 枚举期间在 bMaxPower 字段中声明其所需的功率。 如果要消耗超过 100 mA 的电流,我建议将设备配置为 USB HID 或 USB CDC 设备,因为这些通常比 DFU 更容易实现。   谢谢!   BR 爱丽丝
View full article
T1042D4RDB networking problems when booting from SD card I'm having problems with getting ethernet to work with T1042D4RDB when I'm booting from an SD Card. Here's the output when I boot: SERDES Reference : 0x86 Net: Initializing Fman MMC read: dev # 0, block # 2080, count 128 ... Fman1: Data at 7fdf8f88 is not a firmware No ethernet found. Hit any key to stop autoboot: 0 => md 0x7df8f88 07df8f88: deadbeef deadbeef deadbeef deadbeef ................ 07df8f98: deadbeef deadbeef deadbeef deadbeef ................ 07df8fa8: deadbeef deadbeef deadbeef deadbeef ................ 07df8fb8: deadbeef deadbeef deadbeef deadbeef ................ 07df8fc8: deadbeef deadbeef deadbeef deadbeef ................ 07df8fd8: deadbeef deadbeef deadbeef deadbeef ................ 07df8fe8: deadbeef deadbeef deadbeef deadbeef ................    From the u-boot code, we I can see that u-boot thought it was able to read from the SD card, but "0xdeadbeef" is indicative that nothing was written to RAM at that address. Oddly, the return value from blk_dread() is not checked below in u-boot drivers/net/fm/fm.c:    printf("\nMMC read: dev # %u, block # %u, count %u ...\n", dev, blk, cnt);   mmc_init(mmc);   (void)blk_dread(mmc_get_blk_desc(mmc), blk, cnt, addr); } [deleted] /* Upload the Fman microcode if it's present */ rc = fman_upload_firmware(index, &reg->fm_imem, addr); if (rc)    return rc; env_set_addr("fman_ucode", addr); Re: T1042D4RDB networking problems when booting from SD card KrogerFeedback is a customer survey that gives shoppers an opportunity to share their experience with Kroger. After completing a recent purchase, customers may be invited to provide feedback about store cleanliness, product availability, checkout speed, employee service, and overall satisfaction. The survey is designed to help Kroger understand what customers enjoy and where improvements may be needed. Participants should keep their receipt handy because it may contain information required to access the survey. Answering the questions honestly and thoughtfully helps Kroger improve its products and services. Depending on the current promotion, eligible participants may also have a chance to receive a reward or enter a sweepstakes. KrogerFeedback Re: T1042D4RDB networking problems when booting from SD card KrogerFeedback is a customer survey that gives shoppers an opportunity to share their experience with Kroger. After completing a recent purchase, customers may be invited to provide feedback about store cleanliness, product availability, checkout speed, KrogerFeedback Re: T1042D4RDB networking problems when booting from SD card Wingstop.com/survey – Mywingstopsurvey.com/usa is an online survey offered by Wingstop, allowing customers to provide valuable feedback on their last visit experience. The Wingstop company would like you to provide feedback to help them understand what can be changed to ensure customers an improved experience. Re: T1042D4RDB networking problems when booting from SD card A login gateway designed just for Lockheed Martin workers is called LMPeople External. Employees can access a range of services through the portal, including pay stubs, benefits, and personal data. Re: T1042D4RDB networking problems when booting from SD card Welcome to the Wendy's Customer Satisfaction Survey. We value your candid feedback and appreciate you taking the time to complete our survey. https://haioly-tsiiv-splieurk.yolasite.com/ Re: T1042D4RDB networking problems when booting from SD card Clearification: this is not for Rasperry PI nor my PC, it's for T1042D4RDB. Re: T1042D4RDB networking problems when booting from SD card I'm not using SDK v2.0. It's quite old and not compatible with Ubuntu 18, when I tried(Python 2 vs. 3 problems, near as I can tell). I'm using Poky 2.6.1 Questions: 1. Why would Poky 2.6.1 ship with 3 different versions? 2. Why ship with the latest one that doesn't work? Cheers, Re: T1042D4RDB networking problems when booting from SD card FMan microcode revision has to be consistent with the SDK revision. My assumption was that SDK v2.0 is used. Re: T1042D4RDB networking problems when booting from SD card I see! Thanks! I didn't realize the fMan firmware wasn't included in the u-boot image. I tried with 108.5.9, but it didn't work. T1042D4RDB ships with 106.4.18 and it worked. I find it curious that 108.15.9 is included when it doesn't work and that you recommend 107.4.2.  How did you arrive at the conclusion that 107.4.2 is the right version to program? $ ls tmp/deploy/images/t1042d4rdb/fsl_*.bin tmp/deploy/images/t1042d4rdb/fsl_fman_ucode_t1040_r1.1_106_4_18.bin tmp/deploy/images/t1042d4rdb/fsl_fman_ucode_t1040_r1.1_107_4_2.bin tmp/deploy/images/t1042d4rdb/fsl_fman_ucode_t1040_r1.1_108_5_9.bin Re: T1042D4RDB networking problems when booting from SD card It is needed to write FMan microcode (attached) to the SD card from block 0x820. In U-Boot: =>tftp 100000 fsl_fman_ucode_t1040_r1.1_107_4_2.bin =>mmc write 100000 820 37  In Linux: # dd if=fsl_fman_ucode_t1040_r1.1_107_4_2.bin of=/dev/sdb  seek=2080 bs=512 Re: T1042D4RDB networking problems when booting from SD card The White Castle Survey gives customers a simple way to share feedback about their recent dining experience. By completing the survey, you can comment on food quality, service, cleanliness, staff behavior, and overall satisfaction. Your honest responses help White Castle understand what customers enjoy and where improvements may be needed. To participate, keep your recent receipt handy and follow the survey instructions provided by the company. Answer each question carefully based on your actual visit. Depending on the current promotion, completing the survey may also provide an opportunity to receive a reward or special offer. Taking a few minutes to respond can help improve future White Castle visits. WhiteCastle customers Re: T1042D4RDB networking problems when booting from SD card JackListens is the customer feedback survey for Jack in the Box, giving customers an easy way to share their recent dining experiences. The survey typically asks about food quality, service, cleanliness, staff friendliness, and overall satisfaction. To participate, customers may need information from a recent Jack in the Box receipt. By completing the survey honestly, you can help the restaurant understand what customers enjoy and where improvements are needed. Depending on the current promotion, eligible participants may also receive a validation code or other reward. Taking a few minutes to complete JackListens is a simple way to provide valuable feedback about your visit. JackListens
View full article
i.MX 95:M7 和 A55 之间的动态 TRDC/系统管理器资源分配和 GPIO 共享 大家好, 我们正在开发i.MX 95 平台,希望最初使用 M7 内核的 MIPI DSI 外设,然后在运行时将资源移交给 A55 内核。 据我们了解,外围资源及其所有权最初是 在 通过 系统管理器工具 生成/配置的 mx95evk.cfg 文件中为每个逻辑机器/处理器定义的。 我们想澄清以下几点: 动态资源交接: 是否可以在运行时将 MIPI DSI 外设资源从 M7 动态转移到 A55?例如,M7 最初拥有并使用 MIPI DSI,然后释放该资源,之后 A55 接管并使用同一外设。 动态资源分配: 如果支持运行时交接,那么动态更改资源所有权或访问权限的推荐机制/API是什么?这是通过系统管理器、TRDC还是其他机制处理的? GPIO共享: M7 和 A55 是否可以同时访问同一个 GPIO 端口/资源?如果可以,为了安全地共享 GPIO 资源,是否需要进行任何 TRDC 配置或实施任何软件同步机制? 我们非常希望得到关于在 i.MX 95 上实现M7 和 A55 之间的动态外围设备切换和/或资源共享的推荐方法的任何指导。 Re: i.MX 95: Dynamic TRDC/System Manager Resource Allocation and GPIO Sharing Between M7 and A55 你好, 在 i.MX 95 上,MIPI DSI 资源最初可由 M7 使用,之后移交给 A55。资源访问和所有权应通过系统管理器/TRDC 配置进行配置,而实际的运行时交接应由软件处理。TRDC 控制哪些逻辑机器/功能域可以访问外围设备,但它不管理 M7 和 A55 之间的同步。因此,M7 应先完成所有 DSI 操作,停止使用外围设备,并通过 MU/IPC 等核心间机制通知 A55,然后 A55 才能接管控制权。同样,通过适当的 TRDC 配置,可以使 GPIO 资源同时供 M7 和 A55 访问,但同时访问必须通过软件进行同步。对于 DSI 用例,建议的方法是每次只让一个核心积极使用外围设备,并使用 MU/IPC 进行切换。 Re: i.MX 95: Dynamic TRDC/System Manager Resource Allocation and GPIO Sharing Between M7 and A55 我已与AE团队讨论过,请参考以下更新。 在 i.MX 95 上,资源所有权和 TRDC 权限是在构建时静态地在 SM 配置 (mx95evk.cfg) 中定义的。→ 生成的config_.h 文件,并在 MIX 设备上电时由系统管理器 (SM) 应用。*运行时,没有 SCMI/SM 消息可以将外围设备的所有权从一个逻辑机 (LM) 转移到另一个逻辑机。 然而,SM 文档将“将显示屏从一个 LM 移交给另一个 LM”列为 SM_SCMI_PERM_EXCLUSIVE 模型的确切动机用例。所以交接是可以实现的,只是不能通过“转移”所有权来实现。 Q1 & Q2 — MIPI DSI M7 → A55 交接:如何操作 LMM(逻辑机器管理)SCMI 协议仅启动/重置/关闭/挂起/唤醒 LM——它没有 RESOURCE_ASSIGN 或 OWNERSHIP_TRANSFER 消息。请改用时分交接: 在 mx95evk.cfg 中预先授予 BOTH LMs 访问权限。默认情况下,EVK 配置仅将 MIPI_DSI、MIPI_PHY、DC_DISPENG、BLK_CTRL_DISPLAYMIX、显示时钟/电源(PD_DISPLAY、CLK_DISP*)分配给 AP(LM2)的所有者——您还必须将它们添加到 M7 LM(LM1)以允许 M7 优先使用。 将 SM 管理的资源(时钟、电源、RESET)标记为 SM_SCMI_PERM_EXCLUSIVE(api=all),这样来自两个 LM 的请求就不会被静默聚合/覆盖。 在切换时, M7 使 DSI/DCIF 静默,然后通过应用层 IPC(MU 邮箱或 SCMI 通知)向 A55 发出信号。A55(Linux/DRM DSI+DPU 协议栈)随后启动相同的 IP。 交接顺序是客户软件的责任(时间划分)。SM 仅保证 HW 可以从两侧驾驶,因为两个 LM 都已预先获得访问权限。TRDC 所有权不能在运行时重写——只有 SM 可以对 TRDC 进行编程,并且只能从 MIX 上电时的静态配置进行编程。 控制此功能的 TRDC 配置(在 .cfg 文件中定义): MDAC_am=… — 主功能域分配(将总线主控映射到功能域 ID) MBC_am=s.b— 内存块检查 —这是限制外围设备访问的地方。 MRC_am=… — 内存区域检查(大型内存区域,例如 DDR) 每个LM都绑定到一个DID,例如:SM did=2,AP(LM2) did=3,M7(LM1) did=4。 Q3 — M7 和 A55 之间共享 GPIO 是的,TRDC 可以同时授予 M7 功能域和 A55 功能域对同一 GPIO 实例的并发访问(为两个 DID 启用其 MBC 块)。但需要注意一个关键问题,并且有两种支持的模式: 注意: i.MX 95 GPIO没有硬件仲裁——PDR/DR/GDIR 寄存器是物理共享的,因此来自两个核心的非协调读-修改-写操作会相互竞争。 模式 A(不相交引脚 + SW 同步):按照约定为每个内核分配特定引脚(配置已按 LM 分割引脚)。由于数据/方向寄存器组仍然是共享的,因此需要使用硬件信号量/MU来保护并发 RMW,或者确保内核永远不会同时访问同一个寄存器组。 模式 B(SM 仲裁,推荐用于真正共享的实例):通过始终开启的GPIO1进行路由,该 GPIO1 由 SM 拥有,其记录的角色是“仲裁共享访问”。IOMUXC/IOMUX_GPR 同样由 SM 仲裁。Pinmux/daisy 通过 SCMI 引脚控制协议进行设置,并具有每个代理的权限;GPIO数据操作是直接 MMIO。 Re: i.MX 95: Dynamic TRDC/System Manager Resource Allocation and GPIO Sharing Between M7 and A55 大家好, 我们正在与一家公司合作 i.MX 95 19x19 EVK 并且正在尝试在以下两者之间实现 LVDS 显示切换: M7 和 A55/Linux ,预期架构如下: M7: 最初拥有并驱动LVDS显示器。 A55/Linux: Linux 启动后,它随后接管显示控制权。 当前实施情况 作为开发的初始阶段,我们已将 LVDS 显示器配置为由 M7 进行初始化和控制。M7 成功初始化显示器,并将帧缓冲区填充为蓝色,并在 LVDS 面板上正确显示。 我们将以下资源的默认所有权从 A55 更改为 M7 所有权,同时提供 A55 的通行权: DC DC0 DC1 DC_CMDSEQ DC_DISPENG DC_DISPENG_INT DC_FL0 DC_FL1 DC_INT_CTL DC_PIXENGINE DC_XPC DC_YUV0 DC_YUV1 DC_YUV2 DC_YUV3 BLK_CTRL_DISPLAYMIX LVDS MIPI_PHY LDB_PLL CLOCK_DISP1PIX 视频_PLL1 PIN_I2C2_SCL PIN_I2C2_SDA LPI2C2 观察到的行为 目前的行为情况如下: M7 启动并成功初始化显示屏。 蓝色填充的帧缓冲区在 LVDS 面板上正确显示。 M7 运行时,显示屏始终可见。 然后A55/Linux启动过程开始。 Linux内核启动后,显示屏会变黑。 使用以下设备树时:fdtfile imx95-19x19-evk-it6263-lvds1.dtbLinux 在内核启动过程中总是停止运行。 我们没有观察到明显的内核崩溃,也没有在控制台上看到清晰的错误信息。启动过程突然停止。 资源所有权调查 根据我们的理解,资源所有权是通过以下方式静态配置的: 系统管理器配置和所有权不能通过 SCMI 消息在逻辑机器之间动态转移。 因此,我们研究了是否可以将显示资源分配给 M7 和 A55。 然而,一些关键的数据中心资源似乎不支持双重所有权,特别是: DC DC_XPC DC_YUV0 DC_YUV1 DC_YUV2 DC_YUV3 DC_FL0 DC_FL1 DC_2DBLIT 这表明,Linux 可能正在尝试访问 M7 在其 DRM/DPU 或 IT6263/LVDS 初始化期间独占的一个或多个显示资源。 问题 请问您能否帮我们澄清以下问题? 1. 如果资源(例如……)过多,Linux 系统是否会预期会挂起? 华盛顿特区 DC_XPC , DC_YUV* , DC_FL* ,或 DC_2DBLIT 是否为M7独家所有?   2. 在 Linux 启动期间以及 DRM/DPU 和 IT6263/LVDS 初始化期间,A55/Linux 会访问哪些显示资源? 我们尤其想了解以下用户访问的具体资源: Linux DRM/DPU 显示控制器(直流) IT6263驱动程序 LVDS/LDB驱动器 显示时钟/PLL 配置 3. 是否存在受支持的系统管理器资源所有权配置,允许执行以下顺序? M7 初始化并驱动 LVDS 显示器。 A55/Linux 系统正常启动。 随后 A55/Linux 接管显示控制权。 两台逻辑机都可以访问交接所需的资源。 4. 如果 M7 和 A55 之间不能共享 DC 资源,那么 M7 显示和 A55/Linux 共存或显示切换的推荐架构是什么?   5. 即使 Linux 不打算在启动的初始阶段主动驱动显示器,A55/Linux 是否也需要拥有完整的 DC 资源层次结构?   6. 对于此用例,以下方面是否需要进行任何额外的配置更改? 系统管理器资源配置 TRDC权限 SCMI 配置 Linux 设备树 显示/LVDS配置 7. Linux 启动挂起是否可能是由于 A55/Linux 尝试访问 M7 拥有的显示资源,尤其是在初始化 IT6263/LVDS 显示路径期间?     我们现阶段的主要目标是确定 确定 Linux 在早期启动期间以及 DRM/DPU 和 IT6263/LVDS 初始化期间访问的确切显示资源,并确定这些资源是否可以与 M7 所有权共存。 我们已附上 系统管理器配置文件 (.cfg) 和 Linux 启动日志 供参考。 任何关于支持的资源所有权配置、显示资源依赖关系或推荐的实现架构的指导 M7/A55 LVDS 显示屏切换 非常感谢。   谢谢!   Re: i.MX 95: Dynamic TRDC/System Manager Resource Allocation and GPIO Sharing Between M7 and A55 我们有AN15131 来解决这个问题,该 AN 中还附有源代码。 然而,该 AN 的状态为“网络发布待定”,尚未在 nxp.com 上发布。 请稍等几天。
View full article
FreeRTOS_Toggle_Led_Example_S32K312 的 S32K312 FreeRTOS 版本问题 大家好, 我已从NXP网站下载了以下RTD和FreeRTOS软件包: SW32K3_RTD_R23-11_7.0.1_P02_D2603_DesignStudio_updatesite.tar SW32K3_FreeRTOS_11.1.0_0.8.0_CD1_D2603_DesignStudio_updatesite.tar 我使用的是 Windows 系统,并且已成功在S32 Design Studio (V3.6.10)中导入/打开了FreeRTOS_Toggle_Led_Example_S32K312项目。 但是,当我尝试构建应用程序时,遇到了错误#include "FreeRTOSConfig.h 文件未找到",如附件截图 (BE1) 所示。 此外,当我打开项目的.mex文件时文件配置工具显示以下错误(请参考附件Mex文件) “该工具不支持所选处理器。” 请您就以下几点给予指导? 这些RTD和FreeRTOS软件包是否需要特定版本的S32 Design Studio ? S32K312是否需要安装任何其他更新、插件或设备支持包? 构建和运行FreeRTOS_Toggle_Led_Example_S32K312示例应用程序的正确步骤是什么? 我的最终目标是在S32K312 EVB上运行 FreeRTOS。请问能否提供推荐的设置和安装步骤? 我已附上构建错误截图(BE1 和 Mex)供您参考。 感谢您的支持。 此致, 普拉莫德·贾达夫 Re: S32K312 Freertos build issue for the FreeRTOS_Toggle_Led_Example_S32K312 感谢您的快速更新,提供的RTD版本已经解决了我的问题。 Re: S32K312 Freertos build issue for the FreeRTOS_Toggle_Led_Example_S32K312 您好, SW32K3_RTD_R23-11_7.0.1_P02_D2603_DesignStudio_updatesite.zip 仅包含 Crypto 驱动程序。在添加 FreeRTOS 软件包之前,需要先安装基于 RTD 的软件包。 PetrS_0-1788946493548.png 成功安装 RTD 和 FreeRTOS 后,只需从示例创建一个新项目即可。 PetrS_1-1788946542398.png 加载完成后,打开 mex 文件并点击“更新代码”按钮。它应该添加缺失的驱动程序等。 然后您就可以构建演示了。 您也可以在项目资源管理器窗口中右键单击项目,然后选择“更新代码”和“生成项目”。 PetrS_0-1788946711279.png BR,彼得
View full article
Wrynose SDK 对 PowerPC 的支持 您好, 我们正在考虑将基于 T4240rdb 的开发板从 Dunfell 迁移到 Wrynose Yocto SDK。Wrynose SDK 是否支持 PowerPC 板? 如果以上方法都不行,我们还有哪些途径可以获得对PowerPC主板的支持? 谢谢! 苏巴拉奥·纳拉贾拉 泰雷兹集团高级工程师 Re: PowerPC support for Wrynose SDK 你好, NXP Wrynose Yocto SDK 不支持 PowerPC/T4240RDB 板。这是所有较新的 NXP Yocto 版本(Dunfell 之后)都存在的既定限制。 为什么 Wrynose 不支持 PowerPC? NXP 的 Wrynose SDK(Yocto 6.0)专门针对基于 ARM 的 i.MX 和 Layerscape 处理器。QorIQ T 系列(包括 T4240)采用Power 架构(e6500 内核) ,但该架构并未延续到较新的 Yocto SDK 版本中。这与恩智浦的整体战略是一致的: “QorIQ SDK 是一款功能齐全、成熟的基于 Yocto 的软件工具包,适用于 QorIQ 基于 PowerPC 的 P 系列和 T 系列处理器……Layerscape SDK 是一款基于 Ubuntu 的混合型软件工具包,适用于 Layerscape 系列处理器,未来将成为 Layerscape 平台上最新软件的主要交付机制。” NXP 官方支持的最后一个适用于 T4240RDB 的 Yocto 版本是 Dunfell(Yocto 3.1) 。较新的 Yocto 版本(Scarthgap、Wrynose 等)不包含 T4240RDB 或其他 PowerPC T 系列板。 一个已知的版本错误也证实了这一点,该错误发生在 glibc 层——尝试在 Dunfell 事件后的 Yocto 中为 e6500 PowerPC64 架构进行版本会导致以下结果: configure: error: The e6500 subspecies of powerpc64 is not supported. 您的选择 方案一:留在邓费尔(推荐给 T4240RDB 用户) QorIQ Yocto SDK 的 Dunfell 分支仍然是 T4240RDB 最新官方支持的 Yocto 版本。您可以通过以下方式访问: https://github.com/nxp-qoriq/yocto-sdk/tree/dunfell 这是 NXP 推荐给需要稳定、受支持的 Yocto 环境的 PowerPC T 系列客户的路径。 方案二:使用社区/上游资源 NXP 针对 Power Architecture P 系列和 T 系列客户的官方建议是,利用上游社区资源获取更新的内核和 U-Boot 版本: “今后,我们鼓励使用基于 Power Architecture 的 P 系列和 T 系列平台的客户直接从 kernel.org 和 denx.de (uboot) 等社区资源获取启用软件。” 这意味着您可以使用主线源代码为 T4240RDB 构建更新的内核(例如 5.x 或 6.x),但这需要手动集成工作,并且不是 NXP 支持的交钥匙 SDK。 方案三:迁移到基于 ARM 的 Layerscape 平台 如果必须使用较新的 Yocto SDK(包括 Wrynose),则唯一的途径是将硬件平台迁移到基于 ARM 的 Layerscape 处理器(例如 LX2160A、LS1046A、LS1088A),这些处理器在 Wrynose 和未来的 NXP Yocto 版本中都得到完全支持。这是一项意义重大的硬件重新设计工作,但符合恩智浦的长期发展路线图。 选项 4:NXP 专业/高级支持 如果您需要定制 BSP 工作或将 T4240RDB 移植到更新的 Yocto 基线,NXP 可提供处理器和微控制器的专业支持,包括 Linux/Yocto 配方协助和直接联系 NXP 工程师。   此致问候
View full article
S32DS3.5创建的S32K144工程CSEC和Flash驱动不能同时存在 我需要修改以前的一个S32DS3.5的工程以满足新客户的需求。因为已经有了Flash驱动,现在需要新增CSEC部分驱动,我在mex中进行外设配置时,发现新增CSEC之后就会提示错误,删除CSEC或者Flash就正常。请问应该如何解决该问题? IDE:S32DS3.5 SDK: S32 SDK RTM 4.0.1 err.jpg     Re: S32DS3.5创建的S32K144工程CSEC和Flash驱动不能同时存在 你好@ZDDL , 根据 SDK 发行说明,它与 S32 Design Studio (S32DS) 3.4 兼容。与 S32DS 3.5 的兼容性尚未验证,因此我们无法保证其功能正确。 我也强烈建议在单个 IDE 安装中只安装一个 SDK 或 RTD 版本。如果需要多个 SDK/RTD 版本,请为每个版本单独安装 IDE。 danielmartynek_0-1788953256888.png BR,丹尼尔
View full article
T1042D4RDB SDカードからの起動時にネットワークの問題が発生する <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> SDカードから起動しているときにイーサネットがうまく動作しないT1042D4RDB問題が発生しています。 起動時の出力は以下のとおりです。 SERDES参照番号:0x86 ネットワーク: Fmanを初期化しています MMCは「dev #0、ブロック#2080、カウント128...」と表示しました。 Fman1: 7fdf8f888のデータはファームウェアではありません イーサネットは見つかりませんでした。 自動起動を停止するには、任意のキーを押してください: 0 => md 0x7df8f88 07df8f88: デッドビーフ デッドビーフ デッドビーフ デッドビーフ ................ 07df8f98: デッドビーフ デッドビーフ デッドビーフ デッドビーフ ................ 07df8fa8: デッドビーフ デッドビーフ デッドビーフ デッドビーフ ................ 07df8fb8: デッドビーフ デッドビーフ デッドビーフ デッドビーフ ................ 07df8fc8: デッドビーフ デッドビーフ デッドビーフ デッドビーフ ................ 07df8fd8: デッドビーフ デッドビーフ デッドビーフ デッドビーフ ................ 07df8fe8: デッドビーフ デッドビーフ デッドビーフ デッドビーフ ................ u-bootコードから判断すると、u-bootはSDカードから読み取れると思っていましたが、「0xdeadbeef」はそのアドレスでRAMに何も書き込まれていないことを示しています。 奇妙なことに、blk_dread()からの返り値は以下のu-boot ドライバ/net/fm/fm.cで確認されていません。 printf("\nMMC読み取り: デバイス# %u、ブロック# %u、カウント%u ...\n", dev、blk、cnt); mmc_init(mmc); (void)blk_dread(mmc_get_blk_desc(mmc), blk, cnt, アドレス); } [削除済み] /* Fmanマイクロコードが存在する場合はアップロードする */ rc = fman_upload_firmware(index, &reg->fm_imem, addr); if (rc) return rc; env_set_addr("fman_ucode", addr); Re: T1042D4RDB networking problems when booting from SD card KrogerFeedbackは、買い物客がKrogerでの体験を共有する機会を提供する顧客アンケートです。最近の購入を完了した後、顧客は店舗の清潔さ、商品の入手状況、チェックアウト速度、従業員サービス、全体的な満足度についてフィードバックを依頼することがあります。この調査は、クローガーがお客様の好みや改善点を把握することを目的としています。 参加者は、アンケートにアクセスするために必要な情報が記載されている場合があるため、領収書を手元に置いておくべきです。質問に正直かつ思慮深く答えることが、Krogerの製品やサービスの改善に役立ちます。現在のキャンペーン内容によっては、対象となる参加者は報酬を受け取ったり、懸賞に応募したりする機会を得られる場合もあります。 Krogerのフィードバック Re: T1042D4RDB networking problems when booting from SD card KrogerFeedbackは、買い物客がKrogerでの体験を共有する機会を提供する顧客アンケートです。最近の購入を完了した後、顧客は店舗の清潔さ、商品の入手状況、チェックアウト速度についてフィードバックを依頼することがあります。 Krogerのフィードバック Re: T1042D4RDB networking problems when booting from SD card Wingstop.com/survey – Mywingstopsurvey.com/usa Wingstopが提供するオンラインアンケートで、お客様が直近の訪問体験について貴重なフィードバックを提供できます。 Wingstop社は、お客様の体験を向上させるために何を変更できるかを理解するために、あなたにフィードバックを提供してほしいと考えています。 Re: T1042D4RDB networking problems when booting from SD card ロッキード・マーティンの従業員専用に設計されたログインゲートウェイは、 LMPeople Externalと呼ばれています。従業員は給与明細、福利厚生、個人データなど、さまざまなサービスにアクセスできます。 Re: T1042D4RDB networking problems when booting from SD card ウェンディーズ顧客満足度調査へようこそ。皆様からの率直なご意見を大変貴重に思っており、アンケートにご協力いただいたことに感謝いたします。 https://haioly-tsiiv-splieurk.yolasite.com/ Re: T1042D4RDB networking problems when booting from SD card <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> 補足:これはRaspberry Piや私のPC用ではなく、T1042D4RDB用です。 Re: T1042D4RDB networking problems when booting from SD card <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> SDK v2.0は使っていません。かなり古く、Ubuntu 18とは互換性がありませんでした(Python 2と3の問題があるようです)。 私はPoky 2.6.1を使用しています。 質問: 1. Poky 2.6.1にはなぜ3つの異なるバージョンが含まれているのでしょうか? 2. なぜ動作しない最新バージョンを同梱するのか? 乾杯、 Re: T1042D4RDB networking problems when booting from SD card <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> FManのマイクロコードリビジョンはSDKのリビジョンと整合している必要があります。 私の推測ではSDK v2.0が使われていると思っていました。 Re: T1042D4RDB networking problems when booting from SD card <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> なるほど!ありがとうございます!u-bootイメージにfManファームウェアが含まれていないことに気づきませんでした。 108.5.9で試してみましたが、うまくいきませんでした。T1042D4RDBには106.4.18が同梱されており、正常に動作しました。 108.15.9が動作しないのに、それが含まれていること、そして107.4.2を推奨していることが不思議に思います。 107.4.2がプログラミングに適したバージョンであるという結論に至った経緯を教えてください。 $ ls tmp/deploy/images/t1042d4rdb/fsl_*.bin tmp/deploy/images/t1042d4rdb/fsl_fman_ucode_t1040_r1.1_106_4_18.bin tmp/deploy/images/t1042d4rdb/fsl_fman_ucode_t1040_r1.1_107_4_2.bin tmp/deploy/images/t1042d4rdb/fsl_fman_ucode_t1040_r1.1_108_5_9.bin Re: T1042D4RDB networking problems when booting from SD card <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> SDカードの0x820番地から、添付のFManマイクロコードを書き込む必要があります。 In U-Boot: =>tftp 100000 fsl_fman_ucode_t1040_r1.1_107_4_2.bin =>mmc write 100000 820 37  In Linux: # dd if=fsl_fman_ucode_t1040_r1.1_107_4_2.bin of=/dev/sdb  seek=2080 bs=512 Re: T1042D4RDB networking problems when booting from SD card ホワイトキャッスル調査は、お客様が最近の食事体験についてのフィードバックを簡単に共有できる手段を提供します。アンケートに回答することで、食品の質、サービス、清潔さ、スタッフの行動、全体的な満足度についてコメントできます。皆様の率直な回答により、ホワイトキャッスルはお客様が何を楽しんでいるのか、どこで改善が必要かを理解する助けとなります。参加するには、最新の領収書を手元に置き、会社が提供する調査指示に従ってください。 実際の訪問に基づいて、各質問に慎重にお答えください。現在実施中のキャンペーンによっては、アンケートに回答することで報酬や特別オファーを受け取れる場合もあります。数分の返信を取ることで、今後のホワイトキャッスル訪問の質を向上させることができます。 ホワイトキャッスルのお客様 Re: T1042D4RDB networking problems when booting from SD card JackListensはJack in the Boxの**お客様**フィードバック調査で、**お客様**が最近の食事体験を簡単に共有できる仕組みです。この調査では、通常、食品の品質、サービス、清潔さ、スタッフの親しみやすさ、そして全体的な満足度について尋ねられます。 参加するには、最近のジャック・イン・ザ・ボックスのレシートからの情報が必要になる場合があります。アンケートを正直に回答することで、レストランがお客様の好みや改善点を把握するのに役立ちます。現在のキャンペーン内容によっては、対象となる参加者は認証コードやその他の特典を受け取ることができる場合があります。JackListensに数分かけて回答していただくことは、ご来店に関する貴重なフィードバックを提供する簡単な方法です。 ジャックリスンズ
View full article
モータ制御の仕事に関する質問 さて、とても興味深い仕事の面接を受けました。それは電動モーターの制御分野です。問題は、彼が基本的に2つの主要な職務機能を非常に異なって説明していることです。1つはモーターの制御システムの開発で、matlabでのシミュレーション、マイクロコントローラでの実装とテストです。しかし、2つ目の部分はPLC(プログラマブルロジックコントローラー)に関するもので、彼らは自分たちが構築するシステムに何らかの形で組み込まれる関数をいくつか作成している、と彼は私に話しました。さて、私の質問は、自分が最終的に最初の支店で働くことになるのか、それとも2番目の支店で働くことになるのかを、どうすれば知ることができるのかということです。もし両方であれば、どのくらいの割合でしょうか?同じような会社で働いている方がいれば、この2つの側面がどのようにバランスを取っているのか教えてもらえますか?面接官に直接聞いてみるべきでしょうか?ただし、これらは2つの異なるポジションではありません Re: question regarding electrical motor control job こんにちは、タオトミ・ウルシさん、   ご連絡ありがとうございます。   あなたの質問の意味を完全に理解できているか自信がありません。NXP製品やテクノロジについて具体的にどのような情報をお探しですか?より詳しくご相談いただければ、より詳しくご案内いたします。   こちらがNXPのウェブサイトです。 https://www.nxp.com/   NXPの職に応募する予定がある場合は、当社の採用情報ページをご覧いただき、以下のリンクから応募してください。 https://nxp.wd3.myworkdayjobs.com/careers   すべての情報があなたの助けになれば幸いです。   BR リナ
View full article