s32g2 QNX PFE driver Hi Teams, software information: PFE QNX driver version: 1.8.0 PFE FW version: 1.11.0 QNX SDP version: 7.1.0 Uboot ATF BSP39.0 When I made these changes: struct udevice *dev = NULL; const struct eth_ops* opsptr; char cmd[128]; /* Enable GMAC eqos eth */ ret = uclass_get_device_by_name(UCLASS_ETH, "ethernet@4033c000", &dev); opsptr = DM_DRIVER_GET(eth_eqos)->ops; ret = opsptr->start(dev); /* Enable PFE driver */ uclass_get_device_by_name(UCLASS_MISC, "pfeng-base", &dev); DM_DRIVER_GET(pfeng)->probe(dev); uclass_get_device_by_name(UCLASS_ETH, "pfe2", &dev); opsptr = DM_DRIVER_GET(pfeng_netif)->ops; opsptr->start(dev); uclass_get_device_by_name(UCLASS_ETH,"pfe1",&dev); opsptr = DM_DRIVER_GET(pfeng_netif)->ops; opsptr->start(dev); uclass_get_device_by_name(UCLASS_ETH,"pfe0",&dev); opsptr = DM_DRIVER_GET(pfeng_netif)->ops; opsptr->start(dev); snprintf(cmd, sizeof(cmd), "scmi_clk gate protocol@14 pfe_ts 1"); run_command(cmd, 0); snprintf(cmd, sizeof(cmd), "scmi_clk gate protocol@14 ftm 1"); run_command(cmd, 0); And use these commands to start the QNX system setenv boot_qnx_atf 'mmc dev 0; fatload mmc 0:1 0x83e00000 s32g274a-rdb2.dtb; run atf_fdt_0to3; run release_cpus; fatload mmc 0:1 0x80080000 ifs-s32g274a-rdb.ui; bootm 0x80080000 - 0x83E00000' setenv atf_fdt_0to3 'fdt addr 0x83e00000; fdt resize; fdt set /cpus/cpu@1 cpu-release-addr <0x0 0xa0000010>; fdt set /cpus/cpu@100 cpu-release-addr <0x0 0xa0000010>; fdt set /cpus/cpu@101 cpu-release-addr <0x0 0xa0000010>;' setenv release_cpus 'run cpu_trap; mp 1 release 0xa0000000; mp 2 release 0xa0000000; mp 3 release 0xa0000000;' setenv cpu_trap 'dcache off; mw.l 0xa0000000 0xd503205f; mw.l 0xa0000004 0x58000060; mw.l 0xa0000008 0xb4ffffc0; mw.l 0xa000000C 0xd61f0000; mw.q 0xa0000010 0x00000000; dcache on;' setenv bootcmd 'run boot_qnx_atf' setenv hwconfig "serdes0:mode=pcie,clock=ext;pcie0:mode=rc;serdes1:mode=xpcs0&xpcs1, clock=ext,fmhz=125;xpcs1_0:speed=2G5;xpcs1_1:speed=1G" setenv skip_scmi_reset_agent '1' saveenv System will startup failed， Starting kernel ... clk pfe1_tx_sgmii already disabled clk pfe1_rx_sgmii already disabled Found PFE version 0x50300 (S32G2) Found PFE version 0x50300 (S32G2) pfe2 Waiting for PHY auto negotiation to complete......... TIMEOUT ! ## Setting pfe_ts clock ... ## Setting ftm0_sys clock ... ## Setting ftm0_ext clock ... ## Setting ftm1_sys clock ... ## Setting ftm1_ext clock ... Board: NXP S32G274A RDB2 Revision E Error bringing up core 1 with error 0 The startup log has been uploaded to the attachment. Best Regards Miles Re: s32g2 QNX PFE driver Hi,miles_yang
Thank you for contacting us.
Could you share more information with me?
1.are you using the customer board or our development board RDB2/RDB3?
2.Do you only use the PFE application on the A core?
BR
Joey Re: s32g2 QNX PFE driver Hi Joey, I am using the customer board, and the CPU is S32G274A. Yes, currently only core A is running. The QNX system is started via Uboot. If the above modifications are not added, the QNX system can start normally. However, after adding the modifications in PFE-DRV_S32G_QNX_1.8.0_IntegrationManual.pdf, the startup fails. please help check.Thanks. Best Regards, Miles
查看全文
