フラッシュにデバッグしない 「uVision 5ソフトウェアを搭載したMIMXRT1170-EVKボードでCMSIS-DAPデバッガーを使用しているときに、「エラー:ファイルをロードできませんでした」というエラーが発生しました。パックインストーラーから 'hello world' サンプルプロジェクトを試みています。何か提案はありますか?」 エラー: ファイル 'ram_0x1400_debug\hello_world_demo_cm4.out' を読み込めませんでした。デバッガが中止されました! i.MX-RT1170  Re:フラッシュへのデバッグができない アームバージョンの異なるバージョンで作業 Time.it いただきありがとうございます。再度、システム環境を確認します。 Re:フラッシュへのデバッグができない パックインストーラーでは、ARM::CMSIS 6.0.0と呼ばれる推奨パックが削除され、建物のみが発生します。なぜそのように発生するのか知っていますか? Re:フラッシュへのデバッグができない ARM::CMSIS 6.0.0がサンプルコードと他のコードのみを削除した場合、それ以外の場合は上記のエラーが発生します。上記のパックバージョンを削除しました。それは正常にビルドされました.誰かがなぜ知っているか? Re:フラッシュへのデバッグができない 5つのエラーが発生し、宣言されていない識別子が発生します。

RTD 4.0 with Design Studio 3.5 I am using S32 Design Studio 3.5 for S32K344 I have downloaded 'SW32K3_RTD_R21-11_4.0.0_P16' and installed it. I would like to use RTD 4.0.0 along with the design studio version I have. That means when I make some configuration from the S32 Config Tool and click 'Update Code', the RTD code should be updated according to 'SW32K3_RTD_R21-11_4.0.0_P16' Currently, in Extension and Updates, I can only see RTD version 3.0.0 How do I link S32 Design Studio to RTD version 4.0.0? Re: RTD 4.0 with Design Studio 3.5 Please click ASK A QUESTION in the community. https://community.nxp.com/t5/S32K/bd-p/S32K Re: RTD 4.0 with Design Studio 3.5 When I tried, the difference between RTD 3.0.0 and RTD 4.0.0 does not ends at there. The "Functional Group" name (as in 'Pins' ConfigTools) must match with PORT configuration. The name _BOARD_InitPeripherals let you set in Port Configuration. There was few more wired and minor miss-read of configuration setups. But, they are easily detected so that the correction did not took long time. My RTD 4.0.0 installation is little different from the above (because I used package manager). Re: RTD 4.0 with Design Studio 3.5 Step2. S32 Design Studio 3.5 Update 8 D2311: SW32_S32DS_3.5.8_D2311.zip I did not install Update 11, not sure if it was caused by this. Re: RTD 4.0 with Design Studio 3.5 Irreproducible; the below message shows what I got after following the instruction. That configuration of packages is erroneous. Re: RTD 4.0 with Design Studio 3.5 S32K3 RTD 4.0.0 is compatible with S32K344. Which S32 Configuration Tool did you choose? Pins tool or Clocks tool or Peripherals tool? The other tools should not support S32K344.  If it is not the above problem, maybe some dependent software packages are missing during installation. It is recommended to refer to this post for offline installation: HOWTO: offline install S32K3 RTD 3.0.0 in S32DS v3.5 The following are the differences between installing S32K3 RTD3.0.0 and RTD 4.0.0: Unchecking Contact all update sites during install to find required software can complete offline installation faster. (When you confirm that you only need to install these selected software) Step2. S32 Design Studio 3.5 Update 8 D2311: SW32_S32DS_3.5.8_D2311.zip Step3. Download and Install S32 Design Studio 3.5.8 Development Package with support for S32K3xx devices(3.5.8_D2311): SW32K3_S32DS_3.5.8_D2311.zip Step4. Download and install S32K396 RTD for development, please download and install S32 Design Studio 3.5.6 RTM with support for S32K39x devices(3.5.6_D2309): SW32K39x_S32DS_3.5.6_D2309.zip Step5. If you only need S32K3 but not S32M2, you do not need to install the fifth step. Step6. Download and install S32K3_Real-Time Drivers AUTOSAR R21-11 Version 4.0.0 Patch 16: SW32K3_RTD_R21-11_4.0.0_P16_DS_updatesite_D2404.zip Need to install S32 Design Studio S32K396 SDK. Re: RTD 4.0 with Design Studio 3.5 I have done as you suggested it works. I installed the RTD 4.0.0 as well from the 'S32DS Extensions and Updates' but I see this issue now Is it that RTD 4.0.0 is not compatible with S32K344? Re: RTD 4.0 with Design Studio 3.5 Hi Window -> Preferences -> S32 Design Studio for S32 Platform -> S32DS Extensions and Updates -> Add -> Archive... Then SW32K3_RTD_R21-11_4.0.0_P16 should appear in S32DS Extensions and Updates. Best Regards, Robin ------------------------------------------------------------------------------- Note: - If this post answers your question, please click the "Mark Correct" button. Thank you! - We are following threads for 7 weeks after the last post, later replies are ignored Please open a new thread and refer to the closed one, if you have a related question at a later point in time. ------------------------------------------------------------------------------- Re: RTD 4.0 with Design Studio 3.5 in case you have offline download the RTD version, you can install it from Help->install new software

如果我使用 ICU 模块来捕获 PWM，ISR 例程会被使用吗？ 尊敬的恩智浦专家： 我想利用 ICU 和 eMIOS 模块来捕获 PWM 信号： 芯片型号为S32K312，四个输入引脚分别为PTD13、PTD14、PTD17和PTE5，我将PTD13分配给eMIOS通道20；将PTD 14分配给eMIOS通道21；将PTD 17分配给eMIOS通道18；将PTE5分配给eMIOS通道19。 我选择SAIC进行测量。 我想咨询一个关于中断的问题，是否必须使用中断来捕获PWM信号，如果我使用轮询函数（例如Icu_GetPulseWidth()）是否会捕获PWM信号。 多谢

SDCard上のLinuxイメージからの起動後にIMX 8m Mini EVK wifi(WLAN)が表示されない IMX 8M Mini LPDDR4 EVKを起動しようとしています。NXPのWebサイト(LF_v6.6.23-2.0.0_images_IMX8MMEVK)から画像を読み込んでみました。起動後、ifconfigコマンドでwifiを確認しましたが、wlanは見つかりませんでした。 Wi-Fiを接続するためのwlanがないことに問題がある可能性がありますか。 ifconfigの出力は次のとおりです   root@imx8mmevk:~# ifconfig eth0: flags=-28669 mtu 1500 ether 00:04:9f:08:97:37 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lo: flags=73 mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10 loop txqueuelen 1000 (Local Loopback) RX packets 91 bytes 7727 (7.5 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 91 bytes 7727 (7.5 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 bootの出力は次のとおりです U-Boot SPL 2024.04+g674440bc73e+p0 (Jun 06 2024 - 10:05:34 +0000) DDRINFO: start DRAM init DDRINFO: DRAM rate 3000MTS DDRINFO:ddrphy calibration done DDRINFO: ddrmix config done SEC0: RNG instantiated Normal Boot Trying to boot from MMC1 NOTICE: Do not release JR0 to NS as it can be used by HAB NOTICE: BL31: v2.10.0 (release):android-14.0.0_2.0.0-rc1-1-g49143a170 NOTICE: BL31: Built : 10:04:22, May 29 2024 U-Boot 2024.04+g674440bc73e+p0 (Jun 06 2024 - 10:05:34 +0000) CPU: i.MX8MMQ rev1.0 1800 MHz (running at 1200 MHz) CPU: Commercial temperature grade (0C to 95C) at 46C Reset cause: POR Model: NXP i.MX8MM EVK board DRAM: 2 GiB TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C1 0x52] Power supply on USB2 TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C1 0x50] Core: 220 devices, 35 uclasses, devicetree: separate MMC: FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... *** Warning - bad CRC, using default environment [*]-Video Link 0adv7535_mipi2hdmi adv7535@3d: Can't find cec device id=0x3c fail to probe panel device adv7535@3d mxs_video lcdif@32e00000: failed to get any video link display timings probe video device failed, ret -22 [0] lcdif@32e00000, video [1] mipi_dsi@32e10000, video_bridge [2] adv7535@3d, panel adv7535_mipi2hdmi adv7535@3d: Can't find cec device id=0x3c fail to probe panel device adv7535@3d mxs_video lcdif@32e00000: failed to get any video link display timings probe video device failed, ret -22 In: serial Out: serial Err: serial SEC0: RNG instantiated switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Net: eth0: ethernet@30be0000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 0 Working FDT set to 43000000 libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND starting USB... Bus usb@32e40000: Port not available. USB is stopped. Please issue 'usb start' first. switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... 48263 bytes read in 5 ms (9.2 MiB/s) Unable to open OP-TEE session (err=-5) mm_communicate failed! Error: Cannot initialize UEFI sub-system, r = 3 switch to partitions #0, OK mmc2(part 0) is current device Scanning mmc 2:1... 47924 bytes read in 14 ms (3.3 MiB/s) Error: Cannot initialize UEFI sub-system, r = 3 Running BSP bootcmd ... switch to partitions #0, OK mmc1 is current device Failed to load 'boot.scr' 35355136 bytes read in 598 ms (56.4 MiB/s) Booting from mmc ... 48263 bytes read in 4 ms (11.5 MiB/s) ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Working FDT set to 43000000 Using Device Tree in place at 0000000043000000, end 000000004300ec86 Working FDT set to 43000000 adv7535_mipi2hdmi adv7535@3d: Can't find cec device id=0x3c fail to probe panel device adv7535@3d mxs_video lcdif@32e00000: failed to get any video link display timings probe video device failed, ret -22 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.6.23-lts-next-06236-gb586a521770e (oe-user@oe-host) (aarch64-poky-linux-gcc (GCC) 13.2.0, GNU ld (GNU Binutils) 2.42.0.20240216) #1 SMP PREEMPT Fri Jun 7 13:15:57 UTC 2024 [ 0.000000] KASLR enabled [ 0.000000] Machine model: FSL i.MX8MM EVK board [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000096000000, size 640 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] OF: reserved mem: 0x0000000096000000..0x00000000bdffffff (655360 KiB) map reusable linux,cma [ 0.000000] OF: reserved mem: 0x00000000be000000..0x00000000bfdfffff (30720 KiB) nomap non-reusable optee_core@be000000 [ 0.000000] OF: reserved mem: 0x00000000bfe00000..0x00000000bfffffff (2048 KiB) nomap non-reusable optee_shm@bfe00000 [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x00000000bdffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x95bce6c0-0x95bd0fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x00000000bdffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bdffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bdffffff] [ 0.000000] On node 0, zone DMA: 8192 pages in unavailable ranges [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.4 [ 0.000000] percpu: Embedded 22 pages/cpu s50536 r8192 d31384 u90112 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttymxc1,115200 root=/dev/mmcblk1p2 rootwait rw [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 508032 [ 0.000000] Policy zone: DMA [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: mapped [mem 0x000000008f800000-0x0000000093800000] (64MB) [ 0.000000] Memory: 1266988K/2064384K available (20992K kernel code, 1630K rwdata, 7756K rodata, 3968K init, 643K bss, 142036K reserved, 655360K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 128 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000038880000 [ 0.000000] ITS: No ITS available, not enabling LPIs [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns [ 0.000001] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns [ 0.000442] Console: colour dummy device 80x25 [ 0.000506] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=32000) [ 0.000517] pid_max: default: 32768 minimum: 301 [ 0.000585] LSM: initializing lsm=capability,integrity [ 0.000674] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.000686] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.002219] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.002300] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.002469] rcu: Hierarchical SRCU implementation. [ 0.002473] rcu: Max phase no-delay instances is 1000. [ 0.003659] EFI services will not be available. [ 0.003871] smp: Bringing up secondary CPUs ... [ 0.004414] Detected VIPT I-cache on CPU1 [ 0.004482] GICv3: CPU1: found redistributor 1 region 0:0x00000000388a0000 [ 0.004524] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.005069] Detected VIPT I-cache on CPU2 [ 0.005116] GICv3: CPU2: found redistributor 2 region 0:0x00000000388c0000 [ 0.005140] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.005610] Detected VIPT I-cache on CPU3 [ 0.005653] GICv3: CPU3: found redistributor 3 region 0:0x00000000388e0000 [ 0.005675] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.005746] smp: Brought up 1 node, 4 CPUs [ 0.005752] SMP: Total of 4 processors activated. [ 0.005756] CPU features: detected: 32-bit EL0 Support [ 0.005759] CPU features: detected: 32-bit EL1 Support [ 0.005763] CPU features: detected: CRC32 instructions [ 0.005826] CPU: All CPU(s) started at EL2 [ 0.005848] alternatives: applying system-wide alternatives [ 0.007703] devtmpfs: initialized [ 0.014982] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.015006] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.033615] pinctrl core: initialized pinctrl subsystem [ 0.035721] DMI not present or invalid. [ 0.036350] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.037377] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations [ 0.037496] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.037611] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.037681] audit: initializing netlink subsys (disabled) [ 0.037803] audit: type=2000 audit(0.036:1): state=initialized audit_enabled=0 res=1 [ 0.038327] thermal_sys: Registered thermal governor 'step_wise' [ 0.038331] thermal_sys: Registered thermal governor 'power_allocator' [ 0.038366] cpuidle: using governor menu [ 0.038569] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.038655] ASID allocator initialised with 32768 entries [ 0.039578] Serial: AMBA PL011 UART driver [ 0.039648] imx mu driver is registered. [ 0.039668] imx rpmsg driver is registered. [ 0.046274] platform soc@0: Fixed dependency cycle(s) with /soc@0/bus@30000000/efuse@30350000/unique-id@4 [ 0.049866] imx8mm-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver [ 0.050553] platform 30350000.efuse: Fixed dependency cycle(s) with /soc@0/bus@30000000/clock-controller@30380000 [ 0.051707] platform 30350000.efuse: Fixed dependency cycle(s) with /soc@0/bus@30000000/clock-controller@30380000 [ 0.058201] platform 32e00000.lcdif: Fixed dependency cycle(s) with /soc@0/bus@32c00000/mipi_dsi@32e10000 [ 0.058428] platform 32e00000.lcdif: Fixed dependency cycle(s) with /soc@0/bus@32c00000/mipi_dsi@32e10000 [ 0.058537] platform 32e10000.mipi_dsi: Fixed dependency cycle(s) with /soc@0/bus@30800000/i2c@30a30000/adv7535@3d [ 0.058566] platform 32e10000.mipi_dsi: Fixed dependency cycle(s) with /soc@0/bus@32c00000/lcdif@32e00000 [ 0.058836] platform 32e20000.csi1_bridge: Fixed dependency cycle(s) with /soc@0/bus@32c00000/mipi_csi@32e30000 [ 0.059069] platform 32e20000.csi1_bridge: Fixed dependency cycle(s) with /soc@0/bus@32c00000/mipi_csi@32e30000 [ 0.059186] platform 32e30000.mipi_csi: Fixed dependency cycle(s) with /soc@0/bus@32c00000/csi1_bridge@32e20000 [ 0.059262] platform 32e30000.mipi_csi: Fixed dependency cycle(s) with /soc@0/bus@30800000/i2c@30a40000/ov5640_mipi@3c [ 0.059912] platform 32e40000.usb: Fixed dependency cycle(s) with /soc@0/bus@30800000/i2c@30a30000/tcpc@50 [ 0.065532] Modules: 2G module region forced by RANDOMIZE_MODULE_REGION_FULL [ 0.065559] Modules: 0 pages in range for non-PLT usage [ 0.065563] Modules: 515488 pages in range for PLT usage [ 0.066247] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.066253] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page [ 0.066258] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages [ 0.066263] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page [ 0.066267] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.066272] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.066276] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages [ 0.066281] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page [ 0.068214] ACPI: Interpreter disabled. [ 0.069174] iommu: Default domain type: Translated [ 0.069183] iommu: DMA domain TLB invalidation policy: strict mode [ 0.069500] SCSI subsystem initialized [ 0.069812] usbcore: registered new interface driver usbfs [ 0.069840] usbcore: registered new interface driver hub [ 0.069868] usbcore: registered new device driver usb [ 0.070979] mc: Linux media interface: v0.10 [ 0.071015] videodev: Linux video capture interface: v2.00 [ 0.071079] pps_core: LinuxPPS API ver. 1 registered [ 0.071083] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.071094] PTP clock support registered [ 0.071263] EDAC MC: Ver: 3.0.0 [ 0.071683] scmi_core: SCMI protocol bus registered [ 0.072082] FPGA manager framework [ 0.072164] Advanced Linux Sound Architecture Driver Initialized. [ 0.072861] Bluetooth: Core ver 2.22 [ 0.072903] NET: Registered PF_BLUETOOTH protocol family [ 0.072907] Bluetooth: HCI device and connection manager initialized [ 0.072915] Bluetooth: HCI socket layer initialized [ 0.072920] Bluetooth: L2CAP socket layer initialized [ 0.072931] Bluetooth: SCO socket layer initialized [ 0.073279] vgaarb: loaded [ 0.073798] clocksource: Switched to clocksource arch_sys_counter [ 0.073998] VFS: Disk quotas dquot_6.6.0 [ 0.074026] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.074186] pnp: PnP ACPI: disabled [ 0.081012] NET: Registered PF_INET protocol family [ 0.081158] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.082708] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.082737] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.082750] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.082898] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear) [ 0.083363] TCP: Hash tables configured (established 16384 bind 16384) [ 0.083457] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.083503] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.083659] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.084083] RPC: Registered named UNIX socket transport module. [ 0.084088] RPC: Registered udp transport module. [ 0.084090] RPC: Registered tcp transport module. [ 0.084093] RPC: Registered tcp-with-tls transport module. [ 0.084095] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.085136] PCI: CLS 0 bytes, default 64 [ 0.085496] kvm [1]: IPA Size Limit: 40 bits [ 0.087524] kvm [1]: GICv3: no GICV resource entry [ 0.087530] kvm [1]: disabling GICv2 emulation [ 0.087545] kvm [1]: GIC system register CPU interface enabled [ 0.087570] kvm [1]: vgic interrupt IRQ9 [ 0.087590] kvm [1]: Hyp mode initialized successfully [ 0.088771] Initialise system trusted keyrings [ 0.088945] workingset: timestamp_bits=42 max_order=19 bucket_order=0 [ 0.089216] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.089428] NFS: Registering the id_resolver key type [ 0.089449] Key type id_resolver registered [ 0.089452] Key type id_legacy registered [ 0.089470] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.089476] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.089493] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.089674] 9p: Installing v9fs 9p2000 file system support [ 0.122152] Key type asymmetric registered [ 0.122157] Asymmetric key parser 'x509' registered [ 0.122197] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) [ 0.122203] io scheduler mq-deadline registered [ 0.122207] io scheduler kyber registered [ 0.122232] io scheduler bfq registered [ 0.129175] EINJ: ACPI disabled. [ 0.139685] imx-sdma 302c0000.dma-controller: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 [ 0.139702] imx-sdma 302c0000.dma-controller: Falling back to sysfs fallback for: imx/sdma/sdma-imx7d.bin [ 0.145563] mxs-dma 33000000.dma-controller: initialized [ 0.147012] SoC: i.MX8MM revision 1.0 [ 0.147470] Bus freq driver module loaded [ 0.160101] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.163128] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 18, base_baud = 5000000) is a IMX [ 0.163256] serial serial0: tty port ttymxc0 registered [ 0.163777] 30880000.serial: ttymxc2 at MMIO 0x30880000 (irq = 19, base_baud = 5000000) is a IMX [ 0.164450] 30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 20, base_baud = 1500000) is a IMX [ 0.164476] printk: console [ttymxc1] enabled [ 1.462628] imx-drm display-subsystem: bound imx-lcdif-crtc.0 (ops lcdif_crtc_ops) [ 1.470378] imx_sec_dsim_drv 32e10000.mipi_dsi: version number is 0x1060200 [ 1.477409] [drm:drm_bridge_attach] *ERROR* failed to attach bridge /soc@0/bus@32c00000/mipi_dsi@32e10000 to encoder DSI-34: -517 [ 1.489089] imx_sec_dsim_drv 32e10000.mipi_dsi: Failed to attach bridge: 32e10000.mipi_dsi [ 1.497363] imx_sec_dsim_drv 32e10000.mipi_dsi: failed to bind sec dsim bridge: -517 [ 1.511597] loop: module loaded [ 1.516436] megasas: 07.725.01.00-rc1 [ 1.525517] spi-nor spi0.0: n25q256ax1 (32768 Kbytes) [ 1.534880] tun: Universal TUN/TAP device driver, 1.6 [ 1.540902] thunder_xcv, ver 1.0 [ 1.544175] thunder_bgx, ver 1.0 [ 1.547438] nicpf, ver 1.0 [ 1.552405] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 1.559642] hns3: Copyright (c) 2017 Huawei Corporation. [ 1.564994] hclge is initializing [ 1.568355] e1000: Intel(R) PRO/1000 Network Driver [ 1.573241] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 1.579018] e1000e: Intel(R) PRO/1000 Network Driver [ 1.583989] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.589947] igb: Intel(R) Gigabit Ethernet Network Driver [ 1.595394] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.601004] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 1.607282] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.613380] sky2: driver version 1.30 [ 1.617626] usbcore: registered new device driver r8152-cfgselector [ 1.623928] usbcore: registered new interface driver r8152 [ 1.629876] VFIO - User Level meta-driver version: 0.3 [ 1.637962] usbcore: registered new interface driver uas [ 1.643318] usbcore: registered new interface driver usb-storage [ 1.649394] usbcore: registered new interface driver usbserial_generic [ 1.655950] usbserial: USB Serial support registered for generic [ 1.661983] usbcore: registered new interface driver ftdi_sio [ 1.667756] usbserial: USB Serial support registered for FTDI USB Serial Device [ 1.675100] usbcore: registered new interface driver usb_serial_simple [ 1.681652] usbserial: USB Serial support registered for carelink [ 1.687773] usbserial: USB Serial support registered for flashloader [ 1.694152] usbserial: USB Serial support registered for funsoft [ 1.700181] usbserial: USB Serial support registered for google [ 1.706133] usbserial: USB Serial support registered for hp4x [ 1.711906] usbserial: USB Serial support registered for kaufmann [ 1.718028] usbserial: USB Serial support registered for libtransistor [ 1.724583] usbserial: USB Serial support registered for moto_modem [ 1.730874] usbserial: USB Serial support registered for motorola_tetra [ 1.737514] usbserial: USB Serial support registered for nokia [ 1.743373] usbserial: USB Serial support registered for novatel_gps [ 1.749753] usbserial: USB Serial support registered for siemens_mpi [ 1.756136] usbserial: USB Serial support registered for suunto [ 1.762088] usbserial: USB Serial support registered for vivopay [ 1.768123] usbserial: USB Serial support registered for zio [ 1.773822] usbcore: registered new interface driver usb_ehset_test [ 1.783384] input: 30370000.snvs:snvs-powerkey as /devices/platform/soc@0/30000000.bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0 [ 1.798114] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc0 [ 1.804339] snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to 2024-02-27T17:43:43 UTC (1709055823) [ 1.814333] i2c_dev: i2c /dev entries driver [ 1.820536] mx6s-csi 32e20000.csi1_bridge: initialising [ 1.826750] mxc_mipi-csi 32e30000.mipi_csi: supply mipi-phy not found, using dummy regulator [ 1.835506] mxc_mipi-csi 32e30000.mipi_csi: mipi csi v4l2 device registered [ 1.842485] CSI: Registered sensor subdevice: mxc_mipi-csi.0 [ 1.848173] mxc_mipi-csi 32e30000.mipi_csi: lanes: 2, hs_settle: 13, clk_settle: 2, wclk: 1, freq: 333000000 [ 1.862291] Bluetooth: HCI UART driver ver 2.3 [ 1.866767] Bluetooth: HCI UART protocol H4 registered [ 1.871914] Bluetooth: HCI UART protocol BCSP registered [ 1.877261] Bluetooth: HCI UART protocol LL registered [ 1.882407] Bluetooth: HCI UART protocol ATH3K registered [ 1.887837] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 1.894214] Bluetooth: HCI UART protocol Broadcom registered [ 1.899908] Bluetooth: HCI UART protocol QCA registered [ 1.906794] sdhci: Secure Digital Host Controller Interface driver [ 1.912992] sdhci: Copyright(c) Pierre Ossman [ 1.917982] Synopsys Designware Multimedia Card Interface Driver [ 1.924722] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.932866] ledtrig-cpu: registered to indicate activity on CPUs [ 1.940457] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.947373] usbcore: registered new interface driver usbhid [ 1.952961] usbhid: USB HID core driver [ 1.962472] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA [ 1.970101] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 1.981267] cs_system_cfg: CoreSight Configuration manager initialised [ 1.989034] platform soc@0: Fixed dependency cycle(s) with /soc@0/bus@30000000/efuse@30350000 [ 1.998765] optee: probing for conduit method. [ 2.003249] optee: revision 4.2 (c6be5b57) [ 2.004818] optee: dynamic shared memory is enabled [ 2.014173] optee: initialized driver [ 2.020428] hantrodec 0 : module inserted. Major = 509 [ 2.026196] hantrodec 1 : module inserted. Major = 509 [ 2.032300] hx280enc: module inserted. Major <508> [ 2.042808] NET: Registered PF_LLC protocol family [ 2.047722] u32 classifier [ 2.050484] input device check on [ 2.051735] mmc2: new HS400 Enhanced strobe MMC card at address 0001 [ 2.054154] Actions configured [ 2.054798] NET: Registered PF_INET6 protocol family [ 2.061380] mmcblk2: mmc2:0001 DG4032 29.1 GiB [ 2.065358] Segment Routing with IPv6 [ 2.071768] mmcblk2: p1 p2 [ 2.073439] In-situ OAM (IOAM) with IPv6 [ 2.078562] mmcblk2boot0: mmc2:0001 DG4032 4.00 MiB [ 2.079913] NET: Registered PF_PACKET protocol family [ 2.085402] mmcblk2boot1: mmc2:0001 DG4032 4.00 MiB [ 2.088694] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.095606] mmcblk2rpmb: mmc2:0001 DG4032 4.00 MiB, chardev (234:0) [ 2.099403] Bluetooth: RFCOMM TTY layer initialized [ 2.122751] Bluetooth: RFCOMM socket layer initialized [ 2.127904] Bluetooth: RFCOMM ver 1.11 [ 2.131668] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.136986] Bluetooth: BNEP filters: protocol multicast [ 2.142224] Bluetooth: BNEP socket layer initialized [ 2.147198] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.153126] Bluetooth: HIDP socket layer initialized [ 2.158829] 8021q: 802.1Q VLAN Support v1.8 [ 2.163047] lib80211: common routines for IEEE802.11 drivers [ 2.168762] 9pnet: Installing 9P2000 support [ 2.173204] Key type dns_resolver registered [ 2.178277] NET: Registered PF_VSOCK protocol family [ 2.204517] registered taskstats version 1 [ 2.208762] Loading compiled-in X.509 certificates [ 2.235720] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 2.246301] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 2.256856] gpio gpiochip2: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 2.267408] gpio gpiochip3: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 2.277989] gpio gpiochip4: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 2.291356] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 2.299603] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 2.308055] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 2.316257] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 2.325960] i2c i2c-0: IMX I2C adapter registered [ 2.331986] adv7511 1-003d: supply avdd not found, using dummy regulator [ 2.338819] adv7511 1-003d: supply dvdd not found, using dummy regulator [ 2.341208] nxp-pca9450 0-0025: pca9450a probed. [ 2.345590] adv7511 1-003d: supply pvdd not found, using dummy regulator [ 2.356924] adv7511 1-003d: supply a2vdd not found, using dummy regulator [ 2.363755] adv7511 1-003d: supply v3p3 not found, using dummy regulator [ 2.370497] adv7511 1-003d: supply v1p2 not found, using dummy regulator [ 2.378346] adv7511 1-003d: Probe failed. Remote port 'mipi_dsi@32e10000' disabled [ 2.386155] platform 32e40000.usb: Fixed dependency cycle(s) with /soc@0/bus@30800000/i2c@30a30000/tcpc@50 [ 2.395949] i2c 1-0050: Fixed dependency cycle(s) with /soc@0/bus@32c00000/usb@32e40000 [ 2.408675] i2c i2c-1: IMX I2C adapter registered [ 2.419231] pca953x 2-0020: using no AI [ 2.431487] ov5640_mipi 2-003c: No sensor reset pin available [ 2.437308] ov5640_mipi 2-003c: supply DOVDD not found, using dummy regulator [ 2.444580] ov5640_mipi 2-003c: supply DVDD not found, using dummy regulator [ 2.451676] ov5640_mipi 2-003c: supply AVDD not found, using dummy regulator [ 2.471051] ov5640_mipi 2-003c: Read reg error: reg=300a [ 2.476381] ov5640_mipi 2-003c: Camera is not found [ 2.481536] i2c i2c-2: IMX I2C adapter registered [ 2.489433] imx6q-pcie 33800000.pcie: host bridge /soc@0/pcie@33800000 ranges: [ 2.492273] imx-drm display-subsystem: bound imx-lcdif-crtc.0 (ops lcdif_crtc_ops) [ 2.496786] imx6q-pcie 33800000.pcie: IO 0x001ff80000..0x001ff8ffff -> 0x0000000000 [ 2.504460] imx_sec_dsim_drv 32e10000.mipi_dsi: version number is 0x1060200 [ 2.512483] imx6q-pcie 33800000.pcie: MEM 0x0018000000..0x001fefffff -> 0x0018000000 [ 2.527680] [drm:drm_bridge_attach] *ERROR* failed to attach bridge /soc@0/bus@32c00000/mipi_dsi@32e10000 to encoder DSI-34: -19 [ 2.539280] imx_sec_dsim_drv 32e10000.mipi_dsi: Failed to attach bridge: 32e10000.mipi_dsi [ 2.547560] imx_sec_dsim_drv 32e10000.mipi_dsi: failed to bind sec dsim bridge: -19 [ 2.555232] imx-drm display-subsystem: bound 32e10000.mipi_dsi (ops imx_sec_dsim_ops) [ 2.563997] [drm] Initialized imx-drm 1.0.0 20120507 for display-subsystem on minor 0 [ 2.571857] imx-drm display-subsystem: [drm] Cannot find any crtc or sizes [ 2.582794] pps pps0: new PPS source ptp0 [ 2.698251] mdio_bus 30be0000.ethernet-1:00: Fixed dependency cycle(s) with /soc@0/bus@30800000/ethernet@30be0000/mdio/ethernet-phy@0/vddio-regulator [ 2.730298] imx6q-pcie 33800000.pcie: iATU: unroll T, 4 ob, 4 ib, align 64K, limit 4G [ 2.799666] fec 30be0000.ethernet eth0: registered PHC device 0 [ 2.812701] imx-cpufreq-dt imx-cpufreq-dt: cpu speed grade 3 mkt segment 0 supported-hw 0x8 0x1 [ 2.826685] galcore: clk_get vg clock failed, disable vg! [ 2.826862] sdhci-esdhc-imx 30b50000.mmc: Got CD GPIO [ 2.832671] Galcore version 6.4.11.p2.745085 [ 2.857422] mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA [ 2.871400] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA [ 2.886755] [drm] Initialized vivante 1.0.0 20170808 for 38000000.gpu on minor 1 [ 2.901341] OF: graph: no port node found in /soc@0/bus@30800000/i2c@30a30000/tcpc@50/connector [ 2.910083] OF: graph: no port node found in /soc@0/bus@30800000/i2c@30a30000/tcpc@50/connector [ 2.918805] OF: graph: no port node found in /soc@0/bus@30800000/i2c@30a30000/tcpc@50/connector [ 2.936641] mmc0: new ultra high speed SDR104 SDIO card at address 0001 [ 2.942848] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 2.952867] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 2.959145] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 2.966430] clk: Disabling unused clocks [ 2.970415] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 2.976059] ALSA device list: [ 2.979042] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db [ 2.982046] No soundcards found. [ 3.554679] mmc1: host does not support reading read-only switch, assuming write-enable [ 3.585284] mmc1: new ultra high speed SDR104 SDXC card at address 59b4 [ 3.592890] mmcblk1: mmc1:59b4 118 GiB [ 3.598936] mmcblk1: p1 p2 [ 3.722317] imx6q-pcie 33800000.pcie: Phy link never came up [ 4.731451] imx6q-pcie 33800000.pcie: Phy link never came up [ 4.737458] imx6q-pcie 33800000.pcie: PCI host bridge to bus 0000:00 [ 4.743909] pci_bus 0000:00: root bus resource [bus 00-ff] [ 4.749424] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 4.755630] pci_bus 0000:00: root bus resource [mem 0x18000000-0x1fefffff] [ 4.762554] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400 [ 4.768913] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 4.775205] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref] [ 4.782038] pci 0000:00:00.0: supports D1 [ 4.786068] pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold [ 4.794201] pci 0000:00:00.0: BAR 0: assigned [mem 0x18000000-0x180fffff] [ 4.801008] pci 0000:00:00.0: BAR 6: assigned [mem 0x18100000-0x1810ffff pref] [ 4.808252] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 4.813910] pcieport 0000:00:00.0: PME: Signaling with IRQ 221 [ 5.990876] EXT4-fs (mmcblk1p2): recovery complete [ 6.012321] EXT4-fs (mmcblk1p2): mounted filesystem eff003a1-0ece-4ce4-b9fc-a830febd501b r/w with ordered data mode. Quota mode: none. [ 6.024524] VFS: Mounted root (ext4 filesystem) on device 179:98. [ 6.032790] devtmpfs: mounted [ 6.036670] Freeing unused kernel memory: 3968K [ 6.041544] Run /sbin/init as init process [ 6.392325] systemd[1]: systemd 255.4^ running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA -SMACK +SECCOMP -GCRYPT -GNUTLS -OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 -LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK +XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) [ 6.424223] systemd[1]: Detected architecture arm64. Welcome to NXP i.MX Release Distro 6.6-scarthgap (scarthgap)! [ 6.452135] systemd[1]: Hostname set to . [ 6.965035] systemd[1]: Queued start job for default target Graphical Interface. [ 6.999997] systemd[1]: Created slice Slice /system/getty. [ OK ] Created slice Slice /system/getty. [ 7.024223] systemd[1]: Created slice Slice /system/modprobe. [ OK ] Created slice Slice /system/modprobe. [ 7.048209] systemd[1]: Created slice Slice /system/serial-getty. [ OK ] Created slice Slice /system/serial-getty. [ 7.071674] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 7.094257] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 7.118204] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 7.142111] systemd[1]: Reached target Host and Network Name Lookups. [ OK ] Reached target Host and Network Name Lookups. [ 7.166251] systemd[1]: Reached target Path Units. [ OK ] Reached target Path Units. [ 7.185984] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 7.209984] systemd[1]: Reached target Slice Units. [ OK ] Reached target Slice Units. [ 7.229986] systemd[1]: Reached target Swaps. [ OK ] Reached target Swaps. [ 7.283916] systemd[1]: Listening on RPCbind Server Activation Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ 7.310070] systemd[1]: Reached target RPC Port Mapper. [ OK ] Reached target RPC Port Mapper. [ 7.330522] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 7.350335] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 7.375878] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 7.398501] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 7.422740] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 7.443037] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 7.467516] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 7.490770] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 7.514916] systemd[1]: Listening on User Database Manager Socket. [ OK ] Listening on User Database Manager Socket. [ 7.562056] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System... [ 7.585460] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 7.609166] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 7.630470] systemd[1]: Kernel Trace File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing). [ 7.648779] systemd[1]: Mounting Temporary Directory /tmp... Mounting Temporary Directory /tmp... [ 7.670744] systemd[1]: Starting Create List of Static Device Nodes... Starting Create List of Static Device Nodes... [ 7.718976] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 7.742112] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 7.790920] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 7.810125] fuse: init (API version 7.39) [ 7.816610] systemd[1]: Starting RPC Bind... Starting RPC Bind... [ 7.838121] systemd[1]: File System Check on Root Device was skipped because of an unmet condition check (ConditionPathIsReadWrite=!/). [ 7.857505] systemd[1]: Starting Journal Service... Starting Journal Service... [ 7.899002] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 7.921528] systemd[1]: Starting Generate network units from Kernel command line... Starting Generate network units from Kernel command line... [ 7.949939] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems systemd-journald[151]: Collecting audit messages is enabled. [0m... [ 7.982135] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 8.010944] systemd[1]: Starting Virtual Console Setup... Starting Virtual Console Setup... [ 8.035129] systemd[1]: Started RPC Bind. [ 8.042774] EXT4-fs (mmcblk1p2): re-mounted eff003a1-0ece-4ce4-b9fc-a830febd501b r/w. Quota mode: none. [ OK ] Started RPC Bind. [ 8.067808] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted Temporary Directory /tmp. [ OK ] Finished Create List of Static Device Nodes. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Generate network units from Kernel command line. [ OK ] Finished Remount Root and Kernel File Systems. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Apply Kernel Variables... Starting Create Static Device Nodes in /dev gracefully... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configur[ 8.187854] systemd-journald[151]: Received client request to flush runtime journal. ation File System. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Virtual Console Setup. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create Static Device Nodes in /dev gracefully. Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Preparation for Local File Systems. Mounting /var/volatile... [ 8.423973] audit: type=1334 audit(1709055830.116:2): prog-id=6 op=LOAD [ 8.430860] audit: type=1334 audit(1709055830.124:3): prog-id=7 op=LOAD Starting Rule-based Manager for Device Events and Files... [ OK ] Mounted /var/volatile. Starting Load/Save OS Random Seed... [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Finished Create Volatile Files and Directories. [ 8.608197] audit: type=1334 audit(1709055830.300:4): prog-id=8 op=LOAD Starting Network Time Synchronization... Starting Record System Boot/Shutdown in UTMP... [ 8.669609] audit: type=1334 audit(1709055830.360:5): prog-id=9 op=LOAD [ 8.677095] audit: type=1334 audit(1709055830.360:6): prog-id=10 op=LOAD Starting User D[ 8.685709] audit: type=1334 audit(1709055830.360:7): prog-id=11 op=LOAD atabase Manager... [ OK ] Finished Record System Boot/Shutdown in UTMP. [ OK ] Started User Database Manager. [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Start Psplash Boot Screen... [ OK ] Started Start Psplash Boot Screen. [ OK ] Started Start psplash-systemd progress communication helper. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Started Daily rotation of log files. [ OK ] Reached target Timer Units. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. Starting Docker Socket for the API... Starting sshd.socket... Starting Weston socket... [ OK ] Listening on Docker Socket for the API. [ OK ] Listening on sshd.socket. [ OK ] Listening on Weston socket. [ OK ] Reached target Socket Units. [ OK ] Reached target Basic System. [ OK ] Started Job spooling tools. [ OK ] Started Periodic Command Scheduler. Starting D-Bus System Message Bus... [ OK ] Started Linux Firmware Loader Daemon. [ OK ] Started Configuration for i.MX GPU (Former rc_gpu.S). Starting IPv6 Packet Filtering Framework... Starting IPv4 P[ 9.703805] imx-sdma 30bd0000.dma-controller: firmware found. [ 9.703805] imx-sdma 302b0000.dma-controller: firmware found. [ 9.703981] imx-sdma 30bd0000.dma-controller: loaded firmware 4.6 [ 9.726563] imx-sdma 302c0000.dma-controller: firmware found. Starting Telephony service... [ OK ] Started Parsec Service. [ OK ] Started Updates psplash to basic. [ OK ] Started System Logging Service. [ 9.800500] audit: type=1334 audit(1709055831.492:8): prog-id=12 op=LOAD [ 9.809226] audit: type=1334 audit(1709055831.500:9): prog-id=13 op=LOAD [ 9.818737] audit: type=1334 audit(1709055831.512:10): prog-id=14 op=LOAD Starting User Login Management... Starting OpenSSH Key Generation... [ OK ] Finished IPv6 Packet Filtering Framework. [ OK ] Finished IPv4 Packet Filtering Framework. [ OK ] Reached target Preparation for Network. Starting Network Configuration... [ OK ] Started User Login Management. [ OK ] Started Network Configuration. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Finished OpenSSH Key Generation. [ OK ] Finished Load/Save OS Random Seed. [ OK ] Created slice Slice /system/systemd-fsck. [ OK ] Created slice Slice /system/tee-supplicant. Starting File System Check on /dev/mmcblk2p2... [ OK ] Started TEE Supplicant on teepriv0. [ OK ] Stopped Virtual Console Setup. Stopping Virtual Console Setup... Starting Virtual Console Setup... Expecting device /dev/mmcblk2p1... [ OK ] Started D-Bus System Message Bus. [ OK ] Found device /dev/mmcblk2p1. [ OK ] Started Telephony service. Expecting device /dev/mmcblk1p1... Starting Connection service... Starting File System Check on /dev/mmcblk2p1... [ OK ] Finished Virtual Console Setup. [ OK ] Found device /dev/mmcblk1p1. Starting Save/Restore Sound Card State... Starting File System Check on /dev/mmcblk1p1... [ OK ] Finished File System Check on /dev/mmcblk2p1. Mounting /run/media/boot-mmcblk2p1... [ OK ] Finished Save/Restore Sound Card State. [ OK ] Reached target Sound Card. [ OK ] Started Connection service. [ OK ] Reached target Network. Starting Avahi mDNS/DNS-SD Stack... Starting containerd container runtime... [ OK ] Started Network Time Service. [ OK ] Started Update psplash to network. Starting Terminate Psplash Boot Screen... Starting Permit User Sessions... [ OK ] Mounted /run/media/boot-mmcblk2p1. [FAILED] Failed to start Terminate Psplash Boot Screen. See 'systemctl status psplash-quit.service' for details. [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. Starting Weston, a Wayland compositor, as a system service... Starting WPA supplicant... Starting Hostname Service... [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Finished File System Check on /dev/mmcblk1p1. Mounting /run/media/boot-mmcblk1p1... [ OK ] Started Hostname Service. [ OK ] Started WPA supplicant. [ OK ] Mounted /run/media/boot-mmcblk1p1. [ OK ] Finished File System Check on /dev/mmcblk2p2. Mounting /run/media/root-mmcblk2p2... [ OK ] Mounted /run/media/root-mmcblk2p2. [ OK ] Created slice User Slice of UID 0. Starting User Runtime Directory /run/user/0... [ OK ] Finished User Runtime Directory /run/user/0. Starting User Manager for UID 0... [ OK ] Started User Manager for UID 0. [ OK ] Started Session c1 of User root. [ OK ] Started containerd container runtime. [ OK ] Reached target Multi-User System. [FAILED] Failed to start Weston, a Wayland compositor, as a system service. See 'systemctl status weston.service' for details. [ OK ] Reached target Graphical Interface. Starting Record Runlevel Change in UTMP... [ OK ] Finished Record Runlevel Change in UTMP. NXP i.MX Release Distro 6.6-scarthgap imx8mmevk ttymxc1 imx8mmevk login: root Re:SDCard上のLinuxイメージからの起動後にIMX 8m Mini EVK wifi(WLAN)が表示されない 私はそれを理解しました。ガイド「i.MX LinuxユーザーガイドLF6.1.36_2.1.0」にあります109/123ページ(PDF添付) # For all the Wi-Fi modules: modprobe moal mod_para=nxp/wifi_mod_para.conf $connmanctl connmanctl> enable wifi connmanctl> scan wifi connmanctl> services /* This should list of the network. For example imiM wifi_eafb1cb95e57_696d694d_managed_psk*/ connmanctl> agent on connmanctl> connect wifi_eafb1cb95e57_696d694d_managed_psk /* Enter Passphrase */ Agent RequestInput wifi_c0e4347f5053_4a62726f_managed_psk Passphrase = [ Type=psk, Requirement=mandatory ] Passphrase?123456 connmanctl> quit ifconfig が現在表示中 wfd0: flags=-28605 mtu 1500 inet 192.168.45.111 netmask 255.255.255.0 broadcast 192.168.45.255 inet6 fe80::e8fb:1cff:feb9:5e57 prefixlen 64 scopeid 0x20 ether ea:fb:1c:b9:5e:57 txqueuelen 1000 (Ethernet) RX packets 14 bytes 1544 (1.5 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 47 bytes 6601 (6.4 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 root@imx8mmevk:~# ping www.google.com PING www.google.com (142.251.32.68) 56(84) bytes of data. 64 bytes from yyz12s07-in-f4.1e100.net (142.251.32.68): icmp_seq=1 ttl=106 time=402 ms 64 bytes from yyz12s07-in-f4.1e100.net (142.251.32.68): icmp_seq=2 ttl=106 time=219 ms 64 bytes from yyz12s07-in-f4.1e100.net (142.251.32.68): icmp_seq=3 ttl=106 time=243 ms Re:SDCard上のLinuxイメージからの起動後にIMX 8m Mini EVK wifi(WLAN)が表示されない 誰かがそれが機能しない理由を知っていますか? どんな種類の助けもいただければ幸いです。感謝

从 SDCard 上的 Linux 映像启动后，IMX 8m Mini EVK wifi（WLAN）不显示 我正在尝试启动 IMX 8M Mini LPDDR4 EVK。我从 NXP 网站 (LF_v6.6.23-2.0.0_images_IMX8MMEVK) 加载了图像。启动后，我通过命令 ifconfig 检查了 wifi，但没有找到 wlan。 没有 WLAN 来连接 wifi 可能会出现什么问题？ ifconfig 的输出如下 root@imx8mmevk:~# ifconfig eth0: flags=-28669 mtu 1500 ether 00:04:9f:08:97:37 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lo: flags=73 mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10 loop txqueuelen 1000 (Local Loopback) RX packets 91 bytes 7727 (7.5 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 91 bytes 7727 (7.5 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 boot 的输出如下 U-Boot SPL 2024.04+g674440bc73e+p0 (Jun 06 2024 - 10:05:34 +0000) DDRINFO: start DRAM init DDRINFO: DRAM rate 3000MTS DDRINFO:ddrphy calibration done DDRINFO: ddrmix config done SEC0: RNG instantiated Normal Boot Trying to boot from MMC1 NOTICE: Do not release JR0 to NS as it can be used by HAB NOTICE: BL31: v2.10.0 (release):android-14.0.0_2.0.0-rc1-1-g49143a170 NOTICE: BL31: Built : 10:04:22, May 29 2024 U-Boot 2024.04+g674440bc73e+p0 (Jun 06 2024 - 10:05:34 +0000) CPU: i.MX8MMQ rev1.0 1800 MHz (running at 1200 MHz) CPU: Commercial temperature grade (0C to 95C) at 46C Reset cause: POR Model: NXP i.MX8MM EVK board DRAM: 2 GiB TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C1 0x52] Power supply on USB2 TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C1 0x50] Core: 220 devices, 35 uclasses, devicetree: separate MMC: FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... *** Warning - bad CRC, using default environment [*]-Video Link 0adv7535_mipi2hdmi adv7535@3d: Can't find cec device id=0x3c fail to probe panel device adv7535@3d mxs_video lcdif@32e00000: failed to get any video link display timings probe video device failed, ret -22 [0] lcdif@32e00000, video [1] mipi_dsi@32e10000, video_bridge [2] adv7535@3d, panel adv7535_mipi2hdmi adv7535@3d: Can't find cec device id=0x3c fail to probe panel device adv7535@3d mxs_video lcdif@32e00000: failed to get any video link display timings probe video device failed, ret -22 In: serial Out: serial Err: serial SEC0: RNG instantiated switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Net: eth0: ethernet@30be0000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 0 Working FDT set to 43000000 libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND starting USB... Bus usb@32e40000: Port not available. USB is stopped. Please issue 'usb start' first. switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... 48263 bytes read in 5 ms (9.2 MiB/s) Unable to open OP-TEE session (err=-5) mm_communicate failed! Error: Cannot initialize UEFI sub-system, r = 3 switch to partitions #0, OK mmc2(part 0) is current device Scanning mmc 2:1... 47924 bytes read in 14 ms (3.3 MiB/s) Error: Cannot initialize UEFI sub-system, r = 3 Running BSP bootcmd ... switch to partitions #0, OK mmc1 is current device Failed to load 'boot.scr' 35355136 bytes read in 598 ms (56.4 MiB/s) Booting from mmc ... 48263 bytes read in 4 ms (11.5 MiB/s) ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Working FDT set to 43000000 Using Device Tree in place at 0000000043000000, end 000000004300ec86 Working FDT set to 43000000 adv7535_mipi2hdmi adv7535@3d: Can't find cec device id=0x3c fail to probe panel device adv7535@3d mxs_video lcdif@32e00000: failed to get any video link display timings probe video device failed, ret -22 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.6.23-lts-next-06236-gb586a521770e (oe-user@oe-host) (aarch64-poky-linux-gcc (GCC) 13.2.0, GNU ld (GNU Binutils) 2.42.0.20240216) #1 SMP PREEMPT Fri Jun 7 13:15:57 UTC 2024 [ 0.000000] KASLR enabled [ 0.000000] Machine model: FSL i.MX8MM EVK board [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000096000000, size 640 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] OF: reserved mem: 0x0000000096000000..0x00000000bdffffff (655360 KiB) map reusable linux,cma [ 0.000000] OF: reserved mem: 0x00000000be000000..0x00000000bfdfffff (30720 KiB) nomap non-reusable optee_core@be000000 [ 0.000000] OF: reserved mem: 0x00000000bfe00000..0x00000000bfffffff (2048 KiB) nomap non-reusable optee_shm@bfe00000 [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x00000000bdffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x95bce6c0-0x95bd0fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x00000000bdffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000bdffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bdffffff] [ 0.000000] On node 0, zone DMA: 8192 pages in unavailable ranges [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.4 [ 0.000000] percpu: Embedded 22 pages/cpu s50536 r8192 d31384 u90112 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: console=ttymxc1,115200 root=/dev/mmcblk1p2 rootwait rw [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 508032 [ 0.000000] Policy zone: DMA [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: mapped [mem 0x000000008f800000-0x0000000093800000] (64MB) [ 0.000000] Memory: 1266988K/2064384K available (20992K kernel code, 1630K rwdata, 7756K rodata, 3968K init, 643K bss, 142036K reserved, 655360K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 128 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000038880000 [ 0.000000] ITS: No ITS available, not enabling LPIs [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns [ 0.000001] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns [ 0.000442] Console: colour dummy device 80x25 [ 0.000506] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=32000) [ 0.000517] pid_max: default: 32768 minimum: 301 [ 0.000585] LSM: initializing lsm=capability,integrity [ 0.000674] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.000686] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.002219] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.002300] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.002469] rcu: Hierarchical SRCU implementation. [ 0.002473] rcu: Max phase no-delay instances is 1000. [ 0.003659] EFI services will not be available. [ 0.003871] smp: Bringing up secondary CPUs ... [ 0.004414] Detected VIPT I-cache on CPU1 [ 0.004482] GICv3: CPU1: found redistributor 1 region 0:0x00000000388a0000 [ 0.004524] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.005069] Detected VIPT I-cache on CPU2 [ 0.005116] GICv3: CPU2: found redistributor 2 region 0:0x00000000388c0000 [ 0.005140] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.005610] Detected VIPT I-cache on CPU3 [ 0.005653] GICv3: CPU3: found redistributor 3 region 0:0x00000000388e0000 [ 0.005675] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.005746] smp: Brought up 1 node, 4 CPUs [ 0.005752] SMP: Total of 4 processors activated. [ 0.005756] CPU features: detected: 32-bit EL0 Support [ 0.005759] CPU features: detected: 32-bit EL1 Support [ 0.005763] CPU features: detected: CRC32 instructions [ 0.005826] CPU: All CPU(s) started at EL2 [ 0.005848] alternatives: applying system-wide alternatives [ 0.007703] devtmpfs: initialized [ 0.014982] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.015006] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.033615] pinctrl core: initialized pinctrl subsystem [ 0.035721] DMI not present or invalid. [ 0.036350] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.037377] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations [ 0.037496] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.037611] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.037681] audit: initializing netlink subsys (disabled) [ 0.037803] audit: type=2000 audit(0.036:1): state=initialized audit_enabled=0 res=1 [ 0.038327] thermal_sys: Registered thermal governor 'step_wise' [ 0.038331] thermal_sys: Registered thermal governor 'power_allocator' [ 0.038366] cpuidle: using governor menu [ 0.038569] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.038655] ASID allocator initialised with 32768 entries [ 0.039578] Serial: AMBA PL011 UART driver [ 0.039648] imx mu driver is registered. [ 0.039668] imx rpmsg driver is registered. [ 0.046274] platform soc@0: Fixed dependency cycle(s) with /soc@0/bus@30000000/efuse@30350000/unique-id@4 [ 0.049866] imx8mm-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver [ 0.050553] platform 30350000.efuse: Fixed dependency cycle(s) with /soc@0/bus@30000000/clock-controller@30380000 [ 0.051707] platform 30350000.efuse: Fixed dependency cycle(s) with /soc@0/bus@30000000/clock-controller@30380000 [ 0.058201] platform 32e00000.lcdif: Fixed dependency cycle(s) with /soc@0/bus@32c00000/mipi_dsi@32e10000 [ 0.058428] platform 32e00000.lcdif: Fixed dependency cycle(s) with /soc@0/bus@32c00000/mipi_dsi@32e10000 [ 0.058537] platform 32e10000.mipi_dsi: Fixed dependency cycle(s) with /soc@0/bus@30800000/i2c@30a30000/adv7535@3d [ 0.058566] platform 32e10000.mipi_dsi: Fixed dependency cycle(s) with /soc@0/bus@32c00000/lcdif@32e00000 [ 0.058836] platform 32e20000.csi1_bridge: Fixed dependency cycle(s) with /soc@0/bus@32c00000/mipi_csi@32e30000 [ 0.059069] platform 32e20000.csi1_bridge: Fixed dependency cycle(s) with /soc@0/bus@32c00000/mipi_csi@32e30000 [ 0.059186] platform 32e30000.mipi_csi: Fixed dependency cycle(s) with /soc@0/bus@32c00000/csi1_bridge@32e20000 [ 0.059262] platform 32e30000.mipi_csi: Fixed dependency cycle(s) with /soc@0/bus@30800000/i2c@30a40000/ov5640_mipi@3c [ 0.059912] platform 32e40000.usb: Fixed dependency cycle(s) with /soc@0/bus@30800000/i2c@30a30000/tcpc@50 [ 0.065532] Modules: 2G module region forced by RANDOMIZE_MODULE_REGION_FULL [ 0.065559] Modules: 0 pages in range for non-PLT usage [ 0.065563] Modules: 515488 pages in range for PLT usage [ 0.066247] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.066253] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page [ 0.066258] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages [ 0.066263] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page [ 0.066267] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.066272] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.066276] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages [ 0.066281] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page [ 0.068214] ACPI: Interpreter disabled. [ 0.069174] iommu: Default domain type: Translated [ 0.069183] iommu: DMA domain TLB invalidation policy: strict mode [ 0.069500] SCSI subsystem initialized [ 0.069812] usbcore: registered new interface driver usbfs [ 0.069840] usbcore: registered new interface driver hub [ 0.069868] usbcore: registered new device driver usb [ 0.070979] mc: Linux media interface: v0.10 [ 0.071015] videodev: Linux video capture interface: v2.00 [ 0.071079] pps_core: LinuxPPS API ver. 1 registered [ 0.071083] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.071094] PTP clock support registered [ 0.071263] EDAC MC: Ver: 3.0.0 [ 0.071683] scmi_core: SCMI protocol bus registered [ 0.072082] FPGA manager framework [ 0.072164] Advanced Linux Sound Architecture Driver Initialized. [ 0.072861] Bluetooth: Core ver 2.22 [ 0.072903] NET: Registered PF_BLUETOOTH protocol family [ 0.072907] Bluetooth: HCI device and connection manager initialized [ 0.072915] Bluetooth: HCI socket layer initialized [ 0.072920] Bluetooth: L2CAP socket layer initialized [ 0.072931] Bluetooth: SCO socket layer initialized [ 0.073279] vgaarb: loaded [ 0.073798] clocksource: Switched to clocksource arch_sys_counter [ 0.073998] VFS: Disk quotas dquot_6.6.0 [ 0.074026] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.074186] pnp: PnP ACPI: disabled [ 0.081012] NET: Registered PF_INET protocol family [ 0.081158] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.082708] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.082737] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.082750] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.082898] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear) [ 0.083363] TCP: Hash tables configured (established 16384 bind 16384) [ 0.083457] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.083503] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.083659] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.084083] RPC: Registered named UNIX socket transport module. [ 0.084088] RPC: Registered udp transport module. [ 0.084090] RPC: Registered tcp transport module. [ 0.084093] RPC: Registered tcp-with-tls transport module. [ 0.084095] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.085136] PCI: CLS 0 bytes, default 64 [ 0.085496] kvm [1]: IPA Size Limit: 40 bits [ 0.087524] kvm [1]: GICv3: no GICV resource entry [ 0.087530] kvm [1]: disabling GICv2 emulation [ 0.087545] kvm [1]: GIC system register CPU interface enabled [ 0.087570] kvm [1]: vgic interrupt IRQ9 [ 0.087590] kvm [1]: Hyp mode initialized successfully [ 0.088771] Initialise system trusted keyrings [ 0.088945] workingset: timestamp_bits=42 max_order=19 bucket_order=0 [ 0.089216] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.089428] NFS: Registering the id_resolver key type [ 0.089449] Key type id_resolver registered [ 0.089452] Key type id_legacy registered [ 0.089470] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.089476] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.089493] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.089674] 9p: Installing v9fs 9p2000 file system support [ 0.122152] Key type asymmetric registered [ 0.122157] Asymmetric key parser 'x509' registered [ 0.122197] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) [ 0.122203] io scheduler mq-deadline registered [ 0.122207] io scheduler kyber registered [ 0.122232] io scheduler bfq registered [ 0.129175] EINJ: ACPI disabled. [ 0.139685] imx-sdma 302c0000.dma-controller: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 [ 0.139702] imx-sdma 302c0000.dma-controller: Falling back to sysfs fallback for: imx/sdma/sdma-imx7d.bin [ 0.145563] mxs-dma 33000000.dma-controller: initialized [ 0.147012] SoC: i.MX8MM revision 1.0 [ 0.147470] Bus freq driver module loaded [ 0.160101] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.163128] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 18, base_baud = 5000000) is a IMX [ 0.163256] serial serial0: tty port ttymxc0 registered [ 0.163777] 30880000.serial: ttymxc2 at MMIO 0x30880000 (irq = 19, base_baud = 5000000) is a IMX [ 0.164450] 30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 20, base_baud = 1500000) is a IMX [ 0.164476] printk: console [ttymxc1] enabled [ 1.462628] imx-drm display-subsystem: bound imx-lcdif-crtc.0 (ops lcdif_crtc_ops) [ 1.470378] imx_sec_dsim_drv 32e10000.mipi_dsi: version number is 0x1060200 [ 1.477409] [drm:drm_bridge_attach] *ERROR* failed to attach bridge /soc@0/bus@32c00000/mipi_dsi@32e10000 to encoder DSI-34: -517 [ 1.489089] imx_sec_dsim_drv 32e10000.mipi_dsi: Failed to attach bridge: 32e10000.mipi_dsi [ 1.497363] imx_sec_dsim_drv 32e10000.mipi_dsi: failed to bind sec dsim bridge: -517 [ 1.511597] loop: module loaded [ 1.516436] megasas: 07.725.01.00-rc1 [ 1.525517] spi-nor spi0.0: n25q256ax1 (32768 Kbytes) [ 1.534880] tun: Universal TUN/TAP device driver, 1.6 [ 1.540902] thunder_xcv, ver 1.0 [ 1.544175] thunder_bgx, ver 1.0 [ 1.547438] nicpf, ver 1.0 [ 1.552405] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 1.559642] hns3: Copyright (c) 2017 Huawei Corporation. [ 1.564994] hclge is initializing [ 1.568355] e1000: Intel(R) PRO/1000 Network Driver [ 1.573241] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 1.579018] e1000e: Intel(R) PRO/1000 Network Driver [ 1.583989] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.589947] igb: Intel(R) Gigabit Ethernet Network Driver [ 1.595394] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.601004] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 1.607282] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.613380] sky2: driver version 1.30 [ 1.617626] usbcore: registered new device driver r8152-cfgselector [ 1.623928] usbcore: registered new interface driver r8152 [ 1.629876] VFIO - User Level meta-driver version: 0.3 [ 1.637962] usbcore: registered new interface driver uas [ 1.643318] usbcore: registered new interface driver usb-storage [ 1.649394] usbcore: registered new interface driver usbserial_generic [ 1.655950] usbserial: USB Serial support registered for generic [ 1.661983] usbcore: registered new interface driver ftdi_sio [ 1.667756] usbserial: USB Serial support registered for FTDI USB Serial Device [ 1.675100] usbcore: registered new interface driver usb_serial_simple [ 1.681652] usbserial: USB Serial support registered for carelink [ 1.687773] usbserial: USB Serial support registered for flashloader [ 1.694152] usbserial: USB Serial support registered for funsoft [ 1.700181] usbserial: USB Serial support registered for google [ 1.706133] usbserial: USB Serial support registered for hp4x [ 1.711906] usbserial: USB Serial support registered for kaufmann [ 1.718028] usbserial: USB Serial support registered for libtransistor [ 1.724583] usbserial: USB Serial support registered for moto_modem [ 1.730874] usbserial: USB Serial support registered for motorola_tetra [ 1.737514] usbserial: USB Serial support registered for nokia [ 1.743373] usbserial: USB Serial support registered for novatel_gps [ 1.749753] usbserial: USB Serial support registered for siemens_mpi [ 1.756136] usbserial: USB Serial support registered for suunto [ 1.762088] usbserial: USB Serial support registered for vivopay [ 1.768123] usbserial: USB Serial support registered for zio [ 1.773822] usbcore: registered new interface driver usb_ehset_test [ 1.783384] input: 30370000.snvs:snvs-powerkey as /devices/platform/soc@0/30000000.bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0 [ 1.798114] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc0 [ 1.804339] snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to 2024-02-27T17:43:43 UTC (1709055823) [ 1.814333] i2c_dev: i2c /dev entries driver [ 1.820536] mx6s-csi 32e20000.csi1_bridge: initialising [ 1.826750] mxc_mipi-csi 32e30000.mipi_csi: supply mipi-phy not found, using dummy regulator [ 1.835506] mxc_mipi-csi 32e30000.mipi_csi: mipi csi v4l2 device registered [ 1.842485] CSI: Registered sensor subdevice: mxc_mipi-csi.0 [ 1.848173] mxc_mipi-csi 32e30000.mipi_csi: lanes: 2, hs_settle: 13, clk_settle: 2, wclk: 1, freq: 333000000 [ 1.862291] Bluetooth: HCI UART driver ver 2.3 [ 1.866767] Bluetooth: HCI UART protocol H4 registered [ 1.871914] Bluetooth: HCI UART protocol BCSP registered [ 1.877261] Bluetooth: HCI UART protocol LL registered [ 1.882407] Bluetooth: HCI UART protocol ATH3K registered [ 1.887837] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 1.894214] Bluetooth: HCI UART protocol Broadcom registered [ 1.899908] Bluetooth: HCI UART protocol QCA registered [ 1.906794] sdhci: Secure Digital Host Controller Interface driver [ 1.912992] sdhci: Copyright(c) Pierre Ossman [ 1.917982] Synopsys Designware Multimedia Card Interface Driver [ 1.924722] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.932866] ledtrig-cpu: registered to indicate activity on CPUs [ 1.940457] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 1.947373] usbcore: registered new interface driver usbhid [ 1.952961] usbhid: USB HID core driver [ 1.962472] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA [ 1.970101] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 1.981267] cs_system_cfg: CoreSight Configuration manager initialised [ 1.989034] platform soc@0: Fixed dependency cycle(s) with /soc@0/bus@30000000/efuse@30350000 [ 1.998765] optee: probing for conduit method. [ 2.003249] optee: revision 4.2 (c6be5b57) [ 2.004818] optee: dynamic shared memory is enabled [ 2.014173] optee: initialized driver [ 2.020428] hantrodec 0 : module inserted. Major = 509 [ 2.026196] hantrodec 1 : module inserted. Major = 509 [ 2.032300] hx280enc: module inserted. Major <508> [ 2.042808] NET: Registered PF_LLC protocol family [ 2.047722] u32 classifier [ 2.050484] input device check on [ 2.051735] mmc2: new HS400 Enhanced strobe MMC card at address 0001 [ 2.054154] Actions configured [ 2.054798] NET: Registered PF_INET6 protocol family [ 2.061380] mmcblk2: mmc2:0001 DG4032 29.1 GiB [ 2.065358] Segment Routing with IPv6 [ 2.071768] mmcblk2: p1 p2 [ 2.073439] In-situ OAM (IOAM) with IPv6 [ 2.078562] mmcblk2boot0: mmc2:0001 DG4032 4.00 MiB [ 2.079913] NET: Registered PF_PACKET protocol family [ 2.085402] mmcblk2boot1: mmc2:0001 DG4032 4.00 MiB [ 2.088694] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.095606] mmcblk2rpmb: mmc2:0001 DG4032 4.00 MiB, chardev (234:0) [ 2.099403] Bluetooth: RFCOMM TTY layer initialized [ 2.122751] Bluetooth: RFCOMM socket layer initialized [ 2.127904] Bluetooth: RFCOMM ver 1.11 [ 2.131668] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.136986] Bluetooth: BNEP filters: protocol multicast [ 2.142224] Bluetooth: BNEP socket layer initialized [ 2.147198] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.153126] Bluetooth: HIDP socket layer initialized [ 2.158829] 8021q: 802.1Q VLAN Support v1.8 [ 2.163047] lib80211: common routines for IEEE802.11 drivers [ 2.168762] 9pnet: Installing 9P2000 support [ 2.173204] Key type dns_resolver registered [ 2.178277] NET: Registered PF_VSOCK protocol family [ 2.204517] registered taskstats version 1 [ 2.208762] Loading compiled-in X.509 certificates [ 2.235720] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 2.246301] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 2.256856] gpio gpiochip2: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 2.267408] gpio gpiochip3: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 2.277989] gpio gpiochip4: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 2.291356] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 2.299603] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 2.308055] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 2.316257] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 2.325960] i2c i2c-0: IMX I2C adapter registered [ 2.331986] adv7511 1-003d: supply avdd not found, using dummy regulator [ 2.338819] adv7511 1-003d: supply dvdd not found, using dummy regulator [ 2.341208] nxp-pca9450 0-0025: pca9450a probed. [ 2.345590] adv7511 1-003d: supply pvdd not found, using dummy regulator [ 2.356924] adv7511 1-003d: supply a2vdd not found, using dummy regulator [ 2.363755] adv7511 1-003d: supply v3p3 not found, using dummy regulator [ 2.370497] adv7511 1-003d: supply v1p2 not found, using dummy regulator [ 2.378346] adv7511 1-003d: Probe failed. Remote port 'mipi_dsi@32e10000' disabled [ 2.386155] platform 32e40000.usb: Fixed dependency cycle(s) with /soc@0/bus@30800000/i2c@30a30000/tcpc@50 [ 2.395949] i2c 1-0050: Fixed dependency cycle(s) with /soc@0/bus@32c00000/usb@32e40000 [ 2.408675] i2c i2c-1: IMX I2C adapter registered [ 2.419231] pca953x 2-0020: using no AI [ 2.431487] ov5640_mipi 2-003c: No sensor reset pin available [ 2.437308] ov5640_mipi 2-003c: supply DOVDD not found, using dummy regulator [ 2.444580] ov5640_mipi 2-003c: supply DVDD not found, using dummy regulator [ 2.451676] ov5640_mipi 2-003c: supply AVDD not found, using dummy regulator [ 2.471051] ov5640_mipi 2-003c: Read reg error: reg=300a [ 2.476381] ov5640_mipi 2-003c: Camera is not found [ 2.481536] i2c i2c-2: IMX I2C adapter registered [ 2.489433] imx6q-pcie 33800000.pcie: host bridge /soc@0/pcie@33800000 ranges: [ 2.492273] imx-drm display-subsystem: bound imx-lcdif-crtc.0 (ops lcdif_crtc_ops) [ 2.496786] imx6q-pcie 33800000.pcie: IO 0x001ff80000..0x001ff8ffff -> 0x0000000000 [ 2.504460] imx_sec_dsim_drv 32e10000.mipi_dsi: version number is 0x1060200 [ 2.512483] imx6q-pcie 33800000.pcie: MEM 0x0018000000..0x001fefffff -> 0x0018000000 [ 2.527680] [drm:drm_bridge_attach] *ERROR* failed to attach bridge /soc@0/bus@32c00000/mipi_dsi@32e10000 to encoder DSI-34: -19 [ 2.539280] imx_sec_dsim_drv 32e10000.mipi_dsi: Failed to attach bridge: 32e10000.mipi_dsi [ 2.547560] imx_sec_dsim_drv 32e10000.mipi_dsi: failed to bind sec dsim bridge: -19 [ 2.555232] imx-drm display-subsystem: bound 32e10000.mipi_dsi (ops imx_sec_dsim_ops) [ 2.563997] [drm] Initialized imx-drm 1.0.0 20120507 for display-subsystem on minor 0 [ 2.571857] imx-drm display-subsystem: [drm] Cannot find any crtc or sizes [ 2.582794] pps pps0: new PPS source ptp0 [ 2.698251] mdio_bus 30be0000.ethernet-1:00: Fixed dependency cycle(s) with /soc@0/bus@30800000/ethernet@30be0000/mdio/ethernet-phy@0/vddio-regulator [ 2.730298] imx6q-pcie 33800000.pcie: iATU: unroll T, 4 ob, 4 ib, align 64K, limit 4G [ 2.799666] fec 30be0000.ethernet eth0: registered PHC device 0 [ 2.812701] imx-cpufreq-dt imx-cpufreq-dt: cpu speed grade 3 mkt segment 0 supported-hw 0x8 0x1 [ 2.826685] galcore: clk_get vg clock failed, disable vg! [ 2.826862] sdhci-esdhc-imx 30b50000.mmc: Got CD GPIO [ 2.832671] Galcore version 6.4.11.p2.745085 [ 2.857422] mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA [ 2.871400] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA [ 2.886755] [drm] Initialized vivante 1.0.0 20170808 for 38000000.gpu on minor 1 [ 2.901341] OF: graph: no port node found in /soc@0/bus@30800000/i2c@30a30000/tcpc@50/connector [ 2.910083] OF: graph: no port node found in /soc@0/bus@30800000/i2c@30a30000/tcpc@50/connector [ 2.918805] OF: graph: no port node found in /soc@0/bus@30800000/i2c@30a30000/tcpc@50/connector [ 2.936641] mmc0: new ultra high speed SDR104 SDIO card at address 0001 [ 2.942848] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 2.952867] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 2.959145] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 2.966430] clk: Disabling unused clocks [ 2.970415] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 2.976059] ALSA device list: [ 2.979042] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db [ 2.982046] No soundcards found. [ 3.554679] mmc1: host does not support reading read-only switch, assuming write-enable [ 3.585284] mmc1: new ultra high speed SDR104 SDXC card at address 59b4 [ 3.592890] mmcblk1: mmc1:59b4 118 GiB [ 3.598936] mmcblk1: p1 p2 [ 3.722317] imx6q-pcie 33800000.pcie: Phy link never came up [ 4.731451] imx6q-pcie 33800000.pcie: Phy link never came up [ 4.737458] imx6q-pcie 33800000.pcie: PCI host bridge to bus 0000:00 [ 4.743909] pci_bus 0000:00: root bus resource [bus 00-ff] [ 4.749424] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 4.755630] pci_bus 0000:00: root bus resource [mem 0x18000000-0x1fefffff] [ 4.762554] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400 [ 4.768913] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 4.775205] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref] [ 4.782038] pci 0000:00:00.0: supports D1 [ 4.786068] pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold [ 4.794201] pci 0000:00:00.0: BAR 0: assigned [mem 0x18000000-0x180fffff] [ 4.801008] pci 0000:00:00.0: BAR 6: assigned [mem 0x18100000-0x1810ffff pref] [ 4.808252] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 4.813910] pcieport 0000:00:00.0: PME: Signaling with IRQ 221 [ 5.990876] EXT4-fs (mmcblk1p2): recovery complete [ 6.012321] EXT4-fs (mmcblk1p2): mounted filesystem eff003a1-0ece-4ce4-b9fc-a830febd501b r/w with ordered data mode. Quota mode: none. [ 6.024524] VFS: Mounted root (ext4 filesystem) on device 179:98. [ 6.032790] devtmpfs: mounted [ 6.036670] Freeing unused kernel memory: 3968K [ 6.041544] Run /sbin/init as init process [ 6.392325] systemd[1]: systemd 255.4^ running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA -SMACK +SECCOMP -GCRYPT -GNUTLS -OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 -LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK +XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) [ 6.424223] systemd[1]: Detected architecture arm64. Welcome to NXP i.MX Release Distro 6.6-scarthgap (scarthgap)! [ 6.452135] systemd[1]: Hostname set to . [ 6.965035] systemd[1]: Queued start job for default target Graphical Interface. [ 6.999997] systemd[1]: Created slice Slice /system/getty. [ OK ] Created slice Slice /system/getty. [ 7.024223] systemd[1]: Created slice Slice /system/modprobe. [ OK ] Created slice Slice /system/modprobe. [ 7.048209] systemd[1]: Created slice Slice /system/serial-getty. [ OK ] Created slice Slice /system/serial-getty. [ 7.071674] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 7.094257] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 7.118204] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 7.142111] systemd[1]: Reached target Host and Network Name Lookups. [ OK ] Reached target Host and Network Name Lookups. [ 7.166251] systemd[1]: Reached target Path Units. [ OK ] Reached target Path Units. [ 7.185984] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 7.209984] systemd[1]: Reached target Slice Units. [ OK ] Reached target Slice Units. [ 7.229986] systemd[1]: Reached target Swaps. [ OK ] Reached target Swaps. [ 7.283916] systemd[1]: Listening on RPCbind Server Activation Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ 7.310070] systemd[1]: Reached target RPC Port Mapper. [ OK ] Reached target RPC Port Mapper. [ 7.330522] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 7.350335] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 7.375878] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 7.398501] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 7.422740] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 7.443037] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 7.467516] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 7.490770] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 7.514916] systemd[1]: Listening on User Database Manager Socket. [ OK ] Listening on User Database Manager Socket. [ 7.562056] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System... [ 7.585460] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 7.609166] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 7.630470] systemd[1]: Kernel Trace File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing). [ 7.648779] systemd[1]: Mounting Temporary Directory /tmp... Mounting Temporary Directory /tmp... [ 7.670744] systemd[1]: Starting Create List of Static Device Nodes... Starting Create List of Static Device Nodes... [ 7.718976] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 7.742112] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 7.790920] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 7.810125] fuse: init (API version 7.39) [ 7.816610] systemd[1]: Starting RPC Bind... Starting RPC Bind... [ 7.838121] systemd[1]: File System Check on Root Device was skipped because of an unmet condition check (ConditionPathIsReadWrite=!/). [ 7.857505] systemd[1]: Starting Journal Service... Starting Journal Service... [ 7.899002] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 7.921528] systemd[1]: Starting Generate network units from Kernel command line... Starting Generate network units from Kernel command line... [ 7.949939] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems systemd-journald[151]: Collecting audit messages is enabled. [0m... [ 7.982135] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 8.010944] systemd[1]: Starting Virtual Console Setup... Starting Virtual Console Setup... [ 8.035129] systemd[1]: Started RPC Bind. [ 8.042774] EXT4-fs (mmcblk1p2): re-mounted eff003a1-0ece-4ce4-b9fc-a830febd501b r/w. Quota mode: none. [ OK ] Started RPC Bind. [ 8.067808] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted Temporary Directory /tmp. [ OK ] Finished Create List of Static Device Nodes. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Generate network units from Kernel command line. [ OK ] Finished Remount Root and Kernel File Systems. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Apply Kernel Variables... Starting Create Static Device Nodes in /dev gracefully... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configur[ 8.187854] systemd-journald[151]: Received client request to flush runtime journal. ation File System. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Virtual Console Setup. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create Static Device Nodes in /dev gracefully. Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Preparation for Local File Systems. Mounting /var/volatile... [ 8.423973] audit: type=1334 audit(1709055830.116:2): prog-id=6 op=LOAD [ 8.430860] audit: type=1334 audit(1709055830.124:3): prog-id=7 op=LOAD Starting Rule-based Manager for Device Events and Files... [ OK ] Mounted /var/volatile. Starting Load/Save OS Random Seed... [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Finished Create Volatile Files and Directories. [ 8.608197] audit: type=1334 audit(1709055830.300:4): prog-id=8 op=LOAD Starting Network Time Synchronization... Starting Record System Boot/Shutdown in UTMP... [ 8.669609] audit: type=1334 audit(1709055830.360:5): prog-id=9 op=LOAD [ 8.677095] audit: type=1334 audit(1709055830.360:6): prog-id=10 op=LOAD Starting User D[ 8.685709] audit: type=1334 audit(1709055830.360:7): prog-id=11 op=LOAD atabase Manager... [ OK ] Finished Record System Boot/Shutdown in UTMP. [ OK ] Started User Database Manager. [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Start Psplash Boot Screen... [ OK ] Started Start Psplash Boot Screen. [ OK ] Started Start psplash-systemd progress communication helper. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Started Daily rotation of log files. [ OK ] Reached target Timer Units. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. Starting Docker Socket for the API... Starting sshd.socket... Starting Weston socket... [ OK ] Listening on Docker Socket for the API. [ OK ] Listening on sshd.socket. [ OK ] Listening on Weston socket. [ OK ] Reached target Socket Units. [ OK ] Reached target Basic System. [ OK ] Started Job spooling tools. [ OK ] Started Periodic Command Scheduler. Starting D-Bus System Message Bus... [ OK ] Started Linux Firmware Loader Daemon. [ OK ] Started Configuration for i.MX GPU (Former rc_gpu.S). Starting IPv6 Packet Filtering Framework... Starting IPv4 P[ 9.703805] imx-sdma 30bd0000.dma-controller: firmware found. [ 9.703805] imx-sdma 302b0000.dma-controller: firmware found. [ 9.703981] imx-sdma 30bd0000.dma-controller: loaded firmware 4.6 [ 9.726563] imx-sdma 302c0000.dma-controller: firmware found. Starting Telephony service... [ OK ] Started Parsec Service. [ OK ] Started Updates psplash to basic. [ OK ] Started System Logging Service. [ 9.800500] audit: type=1334 audit(1709055831.492:8): prog-id=12 op=LOAD [ 9.809226] audit: type=1334 audit(1709055831.500:9): prog-id=13 op=LOAD [ 9.818737] audit: type=1334 audit(1709055831.512:10): prog-id=14 op=LOAD Starting User Login Management... Starting OpenSSH Key Generation... [ OK ] Finished IPv6 Packet Filtering Framework. [ OK ] Finished IPv4 Packet Filtering Framework. [ OK ] Reached target Preparation for Network. Starting Network Configuration... [ OK ] Started User Login Management. [ OK ] Started Network Configuration. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Finished OpenSSH Key Generation. [ OK ] Finished Load/Save OS Random Seed. [ OK ] Created slice Slice /system/systemd-fsck. [ OK ] Created slice Slice /system/tee-supplicant. Starting File System Check on /dev/mmcblk2p2... [ OK ] Started TEE Supplicant on teepriv0. [ OK ] Stopped Virtual Console Setup. Stopping Virtual Console Setup... Starting Virtual Console Setup... Expecting device /dev/mmcblk2p1... [ OK ] Started D-Bus System Message Bus. [ OK ] Found device /dev/mmcblk2p1. [ OK ] Started Telephony service. Expecting device /dev/mmcblk1p1... Starting Connection service... Starting File System Check on /dev/mmcblk2p1... [ OK ] Finished Virtual Console Setup. [ OK ] Found device /dev/mmcblk1p1. Starting Save/Restore Sound Card State... Starting File System Check on /dev/mmcblk1p1... [ OK ] Finished File System Check on /dev/mmcblk2p1. Mounting /run/media/boot-mmcblk2p1... [ OK ] Finished Save/Restore Sound Card State. [ OK ] Reached target Sound Card. [ OK ] Started Connection service. [ OK ] Reached target Network. Starting Avahi mDNS/DNS-SD Stack... Starting containerd container runtime... [ OK ] Started Network Time Service. [ OK ] Started Update psplash to network. Starting Terminate Psplash Boot Screen... Starting Permit User Sessions... [ OK ] Mounted /run/media/boot-mmcblk2p1. [FAILED] Failed to start Terminate Psplash Boot Screen. See 'systemctl status psplash-quit.service' for details. [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. Starting Weston, a Wayland compositor, as a system service... Starting WPA supplicant... Starting Hostname Service... [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Finished File System Check on /dev/mmcblk1p1. Mounting /run/media/boot-mmcblk1p1... [ OK ] Started Hostname Service. [ OK ] Started WPA supplicant. [ OK ] Mounted /run/media/boot-mmcblk1p1. [ OK ] Finished File System Check on /dev/mmcblk2p2. Mounting /run/media/root-mmcblk2p2... [ OK ] Mounted /run/media/root-mmcblk2p2. [ OK ] Created slice User Slice of UID 0. Starting User Runtime Directory /run/user/0... [ OK ] Finished User Runtime Directory /run/user/0. Starting User Manager for UID 0... [ OK ] Started User Manager for UID 0. [ OK ] Started Session c1 of User root. [ OK ] Started containerd container runtime. [ OK ] Reached target Multi-User System. [FAILED] Failed to start Weston, a Wayland compositor, as a system service. See 'systemctl status weston.service' for details. [ OK ] Reached target Graphical Interface. Starting Record Runlevel Change in UTMP... [ OK ] Finished Record Runlevel Change in UTMP. NXP i.MX Release Distro 6.6-scarthgap imx8mmevk ttymxc1 imx8mmevk login: root 回复：从 SDCard 上的 Linux 映像启动后，IMX 8m Mini EVK wifi（WLAN）不显示 我明白了。它在指南“ i.MX Linux用户指南LF6.1.36_2.1.0 ”中第 109/123 页（附 PDF） # For all the Wi-Fi modules: modprobe moal mod_para=nxp/wifi_mod_para.conf $connmanctl connmanctl> enable wifi connmanctl> scan wifi connmanctl> services /* This should list of the network. For example imiM wifi_eafb1cb95e57_696d694d_managed_psk*/ connmanctl> agent on connmanctl> connect wifi_eafb1cb95e57_696d694d_managed_psk /* Enter Passphrase */ Agent RequestInput wifi_c0e4347f5053_4a62726f_managed_psk Passphrase = [ Type=psk, Requirement=mandatory ] Passphrase?123456 connmanctl> quit ifconfig 显示现在 wfd0: flags=-28605 mtu 1500 inet 192.168.45.111 netmask 255.255.255.0 broadcast 192.168.45.255 inet6 fe80::e8fb:1cff:feb9:5e57 prefixlen 64 scopeid 0x20 ether ea:fb:1c:b9:5e:57 txqueuelen 1000 (Ethernet) RX packets 14 bytes 1544 (1.5 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 47 bytes 6601 (6.4 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 root@imx8mmevk:~# ping www.google.com PING www.google.com (142.251.32.68) 56(84) bytes of data. 64 bytes from yyz12s07-in-f4.1e100.net (142.251.32.68): icmp_seq=1 ttl=106 time=402 ms 64 bytes from yyz12s07-in-f4.1e100.net (142.251.32.68): icmp_seq=2 ttl=106 time=219 ms 64 bytes from yyz12s07-in-f4.1e100.net (142.251.32.68): icmp_seq=3 ttl=106 time=243 ms 回复：从 SDCard 上的 Linux 映像启动后，IMX 8m Mini EVK wifi（WLAN）不显示 有谁知道为什么它不起作用吗？ 任何形式的帮助都将受到赞赏。谢谢

How to turn off the spread spectrum of MIPI CLK and the EOTP of MIPI data on the imx8mini platform Hi： Recently, I have been porting the mipi to lvds chip driver to the 8mini platform. However, the mipi to lvds chip manufacturer has provided feedback that it need to disable the mipi dsi spreading function and the EOTP function in mipi data. How can I disable these functions? Re: How to turn off the spread spectrum of MIPI CLK and the EOTP of MIPI data on the imx8mini platfo Hello @Eddy1  You can refer to this thread. Best regards. Salas.

PCA9420 Charger I am developing a wearable device using the PC9420 and RT6 series. It runs on a battery, so I need to charge it. Question 1.After switching from MODE0 to standby with PWR_DN_EN=1, is it possible to charge it by inputting 5V to VIN? 2.After switching to standby with PWR_DN_EN=1, I would like to turn on the LED when charging is complete. Is this possible if I use the INT pin? I would like the LED to light only when charging is complete. Thank you in advance. Re: PCA9420 Charger   Hi Teruteru Exactly we often recommend to use ship mode getting the charger active. condition: SHIP_EN=1 AND VIN present AND ON=1 AND OPERATION_SEL_FROM_SHIPMODE=1                 Re: PCA9420 Charger Thank you. I checked the data sheet and understood that it can be charged using ShipMode. Do you generally use ShipMode to turn the power off (to save power)? If so, I will use ShipMode. Re: PCA9420 Charger Hi  I will test it next this function and give you feedback ASAP! Re: PCA9420 Charger Thank you for your reply. Yes, that's right. I would like to be able to charge the device even when it's turned off. I understand that the device is turned off when it detects that it's ON and sets PWR_DN_EN=1, but is this done incorrectly? Re: PCA9420 Charger Hi teruteru5678 Question 1.After switching from MODE0 to standby with PWR_DN_EN=1, is it possible to charge it by inputting 5V to VIN? [gw]do you mean enable charger function under power down status? Thanks! BR

複数の EMIOS インスタンスの同期 複数のEMIOSインスタンスを一緒に同期することは可能ですか?現在、EMIOS 1とEMIOS 0を一緒に実行して一部のPWMを生成していますが、位相差があり、これは可変であり、取り除くことはできません。 次の答えから: https://community.nxp.com/t5/S32K/Synchronizing-eMIOS-instances/td-p/1423858、GTBEビットが1つのemisインスタンスに設定されているのがわかりますが、これは私が行ってうまく機能しています。これを複数のインスタンスで何らかの方法で実行できますか?

S32M244 erase/write pflash in ram failed run flash erase/write code in ram is easily failed ，picture below is SDK version，in the project Cache is disabled，and i debug with PE here i want to erase 0x9000,length is 8，but erase failed the project source is in attach file Re: S32M244 erase/write pflash in ram failed the problem also disappeard after I used another board to test the code when I tried to read the FSTAT in the error board，I found the MCU was locked by mistake because the CSEC was enabled and i erased the sector0 without write 0x40d  So it hard to reaappear Re: S32M244 erase/write pflash in ram failed Hi@Helloyt I tested your code several times on my S32M244EVB and did not encounter your problem, which bothered me. You can look at the FSTAT register.

declaration of a LCU function I am trying to generate complimentry PWM using eMIOS and LCU. but upon building the project, the implicit declaration of a function error is coming when using the Lcu_Ip_SetSyncOutputEnable() although i have properly included the Lcu_Ip header file. No erro is coming when using the Lcu_Ip_Init() function. What is the cause of this error and how can it be solved ?? I have attached the project for reference, I am working on S32K3x4 - T172 board. Re: declaration of a LCU function Hi @sagar991  To be able to use the function Lcu_Ip_SetSyncOutputEnable() is required to enable the LCU SYNC functions in Config Tools.  B.R. VaneB

PWM module does not want to access the custom interrupt routine but always jumps to the default rout Hi there, I am working with the FRDM-MCXA153 board. I´m trying to get an interruot on every rising edge using the standart PWM example portet to c++. So far so simpe, bit unfortunately the interrupt always wants to jump tot the standart interrupt routine (declared as WEAK) and ignores my self-written one. The PWM module is configured via ConfigTools -> Peripherals -> FLEXPWM0 and should generate an interrupt at VAL2. Thanks in advance for your help. MCXA Re: PWM module does not want to access the custom interrupt routine but always jumps to the default Hi, if your main-file is written in c++, you need to add extern "C" before your ISR. Following is a short text I found in the startup file: //***************************************************************************** // Forward declaration of the core exception handlers. // When the application defines a handler (with the same name), this will // automatically take precedence over these weak definitions. // If your application is a C++ one, then any interrupt handlers defined // in C++ files within in your main application will need to have C linkage // rather than C++ linkage. To do this, make sure that you are using extern "C" // { .... } around the interrupt handler within your main application code. //*****************************************************************************

Want to isolate LPC55S36 on EVSE-SIG-BRD2X board and work on Lumissil CG5317 Hi team, I am working on EVSE-SIG-BRD2X board, where I want to isolate LPC55S36 chip on the board and work only on Lumissil CG5317. I have two EVSE-SIG-BRD2X boards, one I use it as EVSE and the other one as EV I actually want to test EV - EVSE high level communication between the two boards via Ethernet - PLC bridge So, I have my ISO 15118-2 software stack for both EVSE and EV I will run my EVSE software on one side on a Linux platform and EV software the other side on a Linux software This will establish a client(EV) - server(EVSE) High level communication My circuit is like the below one: PC <---> Ethernet <---> EVSE-SIG-BRD2X( EVSE ) <----> CP,PP <---> EVSE-SIG-BRD2X( EV )<--->Ethernet <---> PC The CP and PP pins facilitate communication between EV and EVSE via power line communication (PLC) I have gone through the below documents to understand and implement 1. UG10140 - EVSE-SIG-BRD2X Board User Guide 2. UM12128 - EVSE-SIG-BRD2X User Manual 3. X-EVSE-SIG-BRD2X Please let me know if any further information is required. Looking forward for your kind response and support Thanks in advance Regards, Somesh Re: EVSE-SIG-BRD2X board bring-up Hi team, I am working on  EasyEVSE EV Charging Signal Board (EVSE-SIG-BRD) with imx93 FRDM dev board  I have followed GitHub - nxp-imx-support/meta-imx-frdm: Yocto layer for i.MX FRDM boards to build the yocto image for imx93 frdm I added meta-nxp-easyevse-mpu (GitHub - nxp-imx-support/meta-nxp-easyevse-mpu: Easy EVSE MPU Yocto Layers)in the directory imx93_yocto_bsp/sources/ and also added in bblayers.conf  now I am facing issue of patch error (below): psti_ubuntu@pstiubuntu-Precision-Tower-7810:/media/psti_ubuntu/VolumeE/imx93_yocto_bsp/frdm-imx93/conf$ bitbake imx-image-full Loading cache: 100% |#################################################################################################| Time: 0:00:04 Loaded 8389 entries from dependency cache. Parsing recipes: 100% |###############################################################################################| Time: 0:00:02 Parsing of 5792 .bb files complete (5788 cached, 4 parsed). 8393 targets, 520 skipped, 18 masked, 0 errors. NOTE: Resolving any missing task queue dependencies Build Configuration: BB_VERSION = "2.8.0" BUILD_SYS = "x86_64-linux" NATIVELSBSTRING = "universal" TARGET_SYS = "aarch64-poky-linux" MACHINE = "imx93frdm" DISTRO = "fsl-imx-xwayland" DISTRO_VERSION = "6.6-scarthgap" TUNE_FEATURES = "aarch64 armv8a crc crypto" TARGET_FPU = "" DISTRO_NAME = "NXP i.MX Release Distro" ROS_DISTRO = "humble" ROS_VERSION = "2" ROS_PYTHON_VERSION = "3" meta meta-poky = "HEAD:f43f393ef0246b7bee6eed8bcf8271cf2b8cdf40" meta-oe meta-multimedia meta-python = "HEAD:80e01188fa822d87d301ee71973c462d7a865493" meta-freescale = "HEAD:0f8091c63dd8805610c09b08409bc58492a3b16f" meta-freescale-3rdparty = "HEAD:6c063450d464eb2f380443c7d9af1b94ce9b9d75" meta-freescale-distro = "HEAD:b9d6a5d9931922558046d230c1f5f4ef6ee72345" meta-imx-bsp meta-imx-sdk meta-imx-ml meta-imx-v2x = "HEAD:7c10a9c047ce8c1fde05c14ec4baf275bc232a57" meta-nxp-demo-experience = "HEAD:8fd7154c05b716e9635279047f65785399432d88" meta-nxp-matter-baseline meta-nxp-openthread = "HEAD:783becb4b5716d989f50db95b7133d38eae5b47b" meta-arm meta-arm-toolchain = "HEAD:1b85bbb4cab9658da3cd926c62038b8559c5c64e" meta-clang = "HEAD:fe561f41aef0cff9e6f96730ab59f28dca2eb682" meta-gnome meta-networking meta-filesystems = "HEAD:80e01188fa822d87d301ee71973c462d7a865493" meta-qt6 = "HEAD:dc13e1bfda4a4757a08c2d6673bc4bac012c4a80" meta-parsec meta-tpm = "HEAD:11ea91192d43d7c2b0b95a93aa63ca7e73e38034" meta-virtualization = "HEAD:6a80f140e387621f62964209a2e07d3bcfb125ce" meta-nxp-easyevse-mpu = "release/easyevse-mpu-2.0:7a106473ee10383b1fcd8d8491d8237ede6c2f38" meta-ros2-humble meta-ros-common meta-ros2 = "master:5fefe7f3c9e733321cb1786539a8c9c7571294cf" meta-imx-bsp meta-nxp-demo-experience = "lf-6.6.36-2.1.0:1377d9d8c658fd78f2a7362e09a75f5c929ff5ce" Sstate summary: Wanted 3675 Local 15 Mirrors 0 Missed 3660 Current 3706 (0% match, 50% complete)############ | ETA: 0:00:01 Removing 683 stale sstate objects for arch imx93frdm: 100% |##########################################################| Time: 0:00:11 Removing 5 stale sstate objects for arch x86_64: 100% |###############################################################| Time: 0:00:00 Removing 2165 stale sstate objects for arch armv8a: 100% |############################################################| Time: 0:00:15 NOTE: Executing Tasks ERROR: linux-imx-6.6.36+git-r0 do_patch: Could not apply patches for imx93frdm. ERROR: linux-imx-6.6.36+git-r0 do_patch: Patch failures can be resolved in the linux source directory /media/psti_ubuntu/VolumeE/imx93_yocto_bsp/frdm-imx93/tmp/work/imx93frdm-poky-linux/linux-imx/6.6.36+git/git) ERROR: linux-imx-6.6.36+git-r0 do_patch: ExecutionError('/media/psti_ubuntu/VolumeE/imx93_yocto_bsp/frdm-imx93/tmp/work/imx93frdm-poky-linux/linux-imx/6.6.36+git/temp/run.do_patch.128119', 1, None, None) ERROR: Logfile of failure stored in: /media/psti_ubuntu/VolumeE/imx93_yocto_bsp/frdm-imx93/tmp/work/imx93frdm-poky-linux/linux-imx/6.6.36+git/temp/log.do_patch.128119 Log data follows: | DEBUG: Executing python function extend_recipe_sysroot | NOTE: Direct dependencies are ['/media/psti_ubuntu/VolumeE/imx93_yocto_bsp/sources/poky/meta/recipes-devtools/quilt/quilt-native_0.67.bb:do_populate_sysroot', '/media/psti_ubuntu/VolumeE/imx93_yocto_bsp/sources/poky/meta/recipes-kernel/kern-tools/kern-tools-native_git.bb:do_populate_sysroot', 'virtual:native:/media/psti_ubuntu/VolumeE/imx93_yocto_bsp/sources/poky/meta/recipes-devtools/patch/patch_2.7.6.bb:do_populate_sysroot'] | NOTE: Installed into sysroot: [] | NOTE: Skipping as already exists in sysroot: ['gettext-minimal-native', 'cmake-native', 'libtool-native', 'quilt-native', 'texinfo-dummy-native', 'kern-tools-native', 'openssl-native', 'expat-native', 'ncurses-native', 'zlib-native', 'git-native', 'make-native', 'patch-native', 'perl-native', 'bzip2-native', 'xz-native', 'zstd-native', 'attr-native', 'ca-certificates-native', 'curl-native', 'gdbm-native'] | DEBUG: Python function extend_recipe_sysroot finished | DEBUG: Executing shell function do_patch | (1/45) 0001-gpio-pca953x-fix-pca953x_irq_bus_sync_unlock-race.patch | (2/45) 0002-arm64-dts-add-i.MX93-11x11-FRDM-basic-support.patch | (3/45) 0003-arm64-dts-add-imx93-11x11-frdm-mt9m114-dts.patch | (4/45) 0004-Add-DSI-Panel-for-imx93.patch | (5/45) 0005-Add-CTP-support-for-waveshare-panel.patch | (6/45) 0006-arm64-dts-add-imx93-11x11-frdm-tianma-wvga-panel-dts.patch | (7/45) 0007-arm64-dts-add-imx93-11x11-frdm-aud-hat-dts.patch | (8/45) 0008-arm64-dts-add-button-support.patch | (9/45) 0009-arm64-dts-add-imx93-11x11-frdm-ov5640-dts.patch | (10/45) 0010-arm64-dts-add-imx93-11x11-frdm-ld.dts-for-lpm.patch | (11/45) 0011-arm64-dts-add-pwm-function-of-the-LED.patch | (12/45) 0012-arm64-dts-add-imx93-11x11-frdm-8mic.dts.patch | (13/45) 0013-arm64-dts-add-imx93-11x11-frdm-lpuart.dts.patch | (14/45) 0014-arm64-dts-add-imx91-frdm-dts-files.patch | (15/45) 0015-arm64-dts-add-imx91-11x11-frdm-tianma-wvga-panel-dts.patch | (16/45) 0016-arm64-dts-add-imx91-11x11-frdm-mt9m114.dts.patch | (17/45) 0017-arm64-dts-add-imx91-11x11-frdm-aud-hat-dts.patch | (18/45) 0018-arm64-dts-add-imx91-11x11-frdm-8mic.dts-and-fix-imx9.patch | (19/45) 0019-arm64-dts-add-imx91-11x11-frdm-lpuart.dts.patch | (20/45) 0020-LF-13459-clk-imx-Fix-the-pll-power-up-flow.patch | (21/45) 0021-thermal-imx91-bug-fix-Temperature-read-returns-Resou.patch | (22/45) 0022-LF-14498-arm64-dts-imx91-Correct-ENET1_TD3-and-I2C2_.patch | (23/45) 0023-arm64-dts-Add-i.MX8MP-FRDM-board-support.patch | (24/45) 0024-arm64-dts-add-os08a20-device-node-for-i.MX8MP-FRDM-b.patch | (25/45) 0025-arm64-dts-add-dual-BOE-EV121WXM-N10-1850-LVDS-panel-.patch | (26/45) 0026-arm64-dts-imx8mp-frdm-add-dual-os08a20-sensors-for-i.patch | (27/45) 0027-arm64-dts-imx8mp-frdm-add-AP1302-support.patch | (28/45) 0028-arm64-dts-imx8mp-frdm-add-dual-AP1302-support.patch | (29/45) 0029-arm64-dts-imx8mp-frdm-add-imx8mp-frdm-8mic.dts.patch | (30/45) 0030-arm64-dts-imx8mp-frdm-enable-7inch-waveshare-panel.patch | (31/45) 0031-arm64-dts-imx8mp-frdm-add-imx8mp-frdm-rpmsg.dts.patch | (32/45) 0032-arm64-dts-imx8mp-frdm-using-green-led-instead-of-blu.patch | (33/45) 0033-arm64-dts-imx8mp-frdm-fix-wifi-reset-pin.patch | (34/45) 0034-arm64-dts-imx8mp-frdm-clean-imx8mp-frdm.dts.patch | (35/45) 0035-arm64-dts-imx8mp-frdm-fix-interrupt-pin-in-imx8mp-fr.patch | (36/45) 0036-Revert-commit-e85faa36ec41d8304a4f0123d6152274595f1e.patch | (37/45) 0037-arm64-dts-imx8mp-frdm-add-AP1302-support-instead-of-.patch | (38/45) 0038-arm64-dts-imx8mp-frdm-add-rpmsg-audio-support.patch | (39/45) 0039-drm-panel-panel-waveshare-dsi-Add-bridge-and-connect.patch | (40/45) 0040-arm64-dts-imx8mp-frdm-update-waveshare-panel-node.patch | (41/45) 0041-drm-panel-remove-wavesahre-node-in-simple-panel.patch | (42/45) 0042-arm64-dts-imx8mp-frdm-add-imx8mp-frdm-iw612-otbr-dts.patch | (43/45) 0001-EasyEVSE-LF6.1.36-DTS-support-for-i.MX8MNLPDDR4-and-.patch | [INFO]: check of .kernel-meta//patches//./0001-EasyEVSE-LF6.1.36-DTS-support-for-i.MX8MNLPDDR4-and-.patch with "git am" did not pass, trying reduced context. | [INFO]: Context reduced git-am of .kernel-meta//patches//./0001-EasyEVSE-LF6.1.36-DTS-support-for-i.MX8MNLPDDR4-and-.patch with "git am" did not work, trying "apply". | /media/psti_ubuntu/VolumeE/imx93_yocto_bsp/frdm-imx93/tmp/work/imx93frdm-poky-linux/linux-imx/6.6.36+git/git/.git/rebase-apply/patch:52: trailing whitespace. | pinctrl-2 = <&pinctrl_cg5317>; | /media/psti_ubuntu/VolumeE/imx93_yocto_bsp/frdm-imx93/tmp/work/imx93frdm-poky-linux/linux-imx/6.6.36+git/git/.git/rebase-apply/patch:328: trailing whitespace. | }; | error: patch failed: arch/arm64/boot/dts/freescale/Makefile:377 | error: arch/arm64/boot/dts/freescale/Makefile: patch does not apply | [ERROR]: Application of .kernel-meta//patches//./0001-EasyEVSE-LF6.1.36-DTS-support-for-i.MX8MNLPDDR4-and-.patch failed. | Patch needs to be refreshed. Sample resolution script: | .git/rebase-apply/resolve_rejects | ERROR: Could not apply patches for imx93frdm. | ERROR: Patch failures can be resolved in the linux source directory /media/psti_ubuntu/VolumeE/imx93_yocto_bsp/frdm-imx93/tmp/work/imx93frdm-poky-linux/linux-imx/6.6.36+git/git) | WARNING: exit code 1 from a shell command. ERROR: Task (/media/psti_ubuntu/VolumeE/imx93_yocto_bsp/sources/meta-imx/meta-imx-bsp/recipes-kernel/linux/linux-imx_6.6.bb:do_patch) failed with exit code '1' NOTE: Tasks Summary: Attempted 7863 tasks of which 7842 didn't need to be rerun and 1 failed. Summary: 1 task failed: /media/psti_ubuntu/VolumeE/imx93_yocto_bsp/sources/meta-imx/meta-imx-bsp/recipes-kernel/linux/linux-imx_6.6.bb:do_patch Summary: There were 3 ERROR messages, returning a non-zero exit code. Looking forward for your kind response and help Thanks in advance. Regards, somesh Re: EVSE-SIG-BRD2X board bring-up Hello, The EVSE Kit for MPU is using i.MX93. You can refer the documents in EVSE page. https://www.nxp.com/design/design-center/development-boards-and-designs/EV-CHRG-STN-MPU If you want to verify it on i.MX8MM, i think you need modify lots of source code to make it work on i.MX8MM based on the Getting Started with the EasyEVSE Development Platform here. https://www.nxp.com/document/guide/getting-started-with-the-easyevse-development-platform-linux-os-wi-fi-6:GS-EV-CHRG-STN-MPU?section=get-software Best Regards, Zhiming EVSE-SIG-BRD2X board bring-up Hi Hope you are doing well! I want to use MII host interface of CG5317 for connection with host MPU (nxp i.MX 8M Mini) my question is 1. How can I achieve this communication using MII host interface? 2. Does the CG5317 chip on EVSE-SIG-BRD2X has firmware already flashed in it? 3. I connected RJ45 port to my host MPU (nxp i.MX 8M Mini) with ethernet but not able to detect the mac address or ip address from my host terminal I have attached screenshots and images of my circuit for your kind reference Regards, somesh Re: Want to isolate LPC55S36 on EVSE-SIG-BRD2X board and work on Lumissil CG5317 Hello, If you only want to test Lumissil CG5317, please use Lumissil CG5317 official board. If you want to only test CG5317 on EVSE-SIG-BRD2X board, you need to do hardware rework and we can't make sure that you can control CG5317 after rework. Best Regards, Zhiming

Difference between MPL3115A2 and MPL3115A2S Hello, I am wondering what is the difference between MPL3115A2 and MPL3115A2S I can't tell why there is a change in reference as the datasheet seems identical. Thanks in advance, Re: Difference between MPL3115A2 and MPL3115A2S Dear CL_ENVEA, yes, this is correct. It is the same component. Thank you for posting the answer here, for other customer's convinience. With Best Regards, Jozef Re: Difference between MPL3115A2 and MPL3115A2S I got a quick reply from the tech support: 100% compatible, just a new fab

siul2_port configuration and functional Group setting in s32ds 3.6 i wanna make each port container(adc, pwm, can, uart and so on) but i got a error about functional Group.  error is there are some duplicated 'NAME' in the PortContainer.  when i write a other PortContainer, portpin Mode, level value, slew Rate is not read. and i get errors. 1. is it imppssible for making multi portcontainer? 2. if it is possible, how it make that? 3. can i get codument or description for setting functional group and adding functional group? thanks for regards. General Re: siul2_port configuration and functional Group setting in s32ds 3.6 Please refer to the introduction in  Interacting with Digital Inputs/Outputs on MR-CANHUBK344  I have added the portpin id 1,2,3,4 in container 0. Re: siul2_port configuration and functional Group setting in s32ds 3.6 @Robin_Shen  i have questions.  1. what is mean portpin id//? portpin id is 5 in your post.  @Robin_Shen  what is meaning portpin id is 5 in your pic? does container 0 already has portpin id 1,2,3,4? exactly i don't know portpin id's meaning. is that just index? 2. if i have assign all of pin in one container, is it has a problem?  why s32ds has a continer? for managing pins??? thanks for regards Re: siul2_port configuration and functional Group setting in s32ds 3.6 Hi Did you add another PortContainer in Pins Tool? I'm not sure if this is what you need. If not please let me know. Best Regards, Robin ------------------------------------------------------------------------------- Note: - If this post answers your question, please click the "ACCEPT AS SOLUTION" button. Thank you! - We are following threads for 7 weeks after the last post, later replies are ignored Please open a new thread and refer to the closed one, if you have a related question at a later point in time. -------------------------------------------------------------------------------

[S32K3XX] C40_Ip using for accessing Code flash memory patition Hi. I am developing flash access using C40_Ip api in bootloader. Data memory partition(0x10000000) can be accessed by that API. But code memory partition(0x500000 ~ 0x007FE000) can not be accessed. Hard fault assert is happened.  C40_Ip API is located in SRAM like below. Could you give me some guide or hint for this debugging? Thank you in advance. Re: [S32K3XX] C40_Ip using for accessing Code flash memory patition Yes. It's work normally Re: [S32K3XX] C40_Ip using for accessing Code flash memory patition Hi@Changhawn Is your problem solved? I see that you have already set your answer as a solution. Re: [S32K3XX] C40_Ip using for accessing Code flash memory patition Basic working is confirmed. My access region is not wrong. Re: [S32K3XX] C40_Ip using for accessing Code flash memory patition I encountered the same problem as you. When writing to the PFLASH, a hardware fault occurred. Could you please tell me how you solved it?

GPIO intentional shutdown Can I shutdown a Flexcomm I2C connection, then reuse the SCL and SDA pins for another purpose? LPC55xx Re: GPIO intentional shutdown Thank you, Alice Re: GPIO intentional shutdown Hello @Bill6  Yes, you can reuse them as normal gpio. BR Alice

哪些 RTD 版本支持 S32K312 平台中的 SafeRTOS 示例代码？ 我们知道它支持 FreeRTOS 并且还有开发示例代码，但我们认为应用程序的安全性更高。您计划何时提供 SafeRTOS 示例代码？可以运行哪些 RTD 版本。谢谢。

Unable to flash i.MX1052 using MCUXpresso GUI Flash Tool. Hi! I am working with a custom board developed from the standard MIMXRT1050-EVKB with a RT1052 and a Windbond W25Q512JV. I tried flashing the SDK example flashloader onto my flash with two custom pin configurations that should boot up the LCD monitor on my board, using the GUI Flash tool. While the tool runs successfully without error, it seems that the tool didnt actually flash any image into the flash. The console log is as below： ----------------------------------------- P&E GDB Server for Arm(R) devices, Version 9.33.00.00 Copyright 2018, P&E Microcomputer Systems Inc, All rights reserved Loading library C:\nxp\MCUXpressoIDE_11.8.1_1197\ide\plugins\com.pemicro.debug.gdbjtag.pne_5.7.3.202310061729\win32\gdi\unit_ngs_arm_internal.dll ... Done. Command line arguments: -interface=USBMULTILINK -port=USB1 -speed=5000 -flashobjectfile=C:\Users\ \Documents\MCUXpressoIDE_11.8.1_1197\workspace\evkbimxrt1050_flashloader\Debug\evkbimxrt1050_flashloader.axf -device=NXP_iMX_IMXRT1052 -programmingtype=0 -runafterprogramming -startserver -singlesession -quitafterprogramming Device selected is NXP_iMX_IMXRT1052 User Specified Hardware Selection : Interface=USBMULTILINK and Port=USB1 Connecting to target. Unable to load libusb0.dll PEmicro Interface detected - Flash Version 11.22 Device is NXP_iMX_IMXRT1052. Mode is In-Circuit Debug. (C)opyright 2012, P&E Microcomputer Systems, Inc. (www.pemicro.com) API version is 101 TARGET XML PATH is C:\nxp\MCUXpressoIDE_11.8.1_1197\ide\plugins\com.pemicro.debug.gdbjtag.pne_5.7.3.202310061729\supportFiles_ARM\target_v7m_vfp.xml Server 1 running on 127.0.0.1:7224 Server 2 running on 127.0.0.1:7226 Server 3 running on 127.0.0.1:7228 Server 4 running on 127.0.0.1:7230 Server 5 running on 127.0.0.1:7232 Server 6 running on 127.0.0.1:7234 Server 7 running on 127.0.0.1:7236 Server 8 running on 127.0.0.1:7238 Server 9 running on 127.0.0.1:7240 Server 10 running on 127.0.0.1:7242 All Servers Running Target Disconnected. ----------------------------------------- It seems like the tool just terminated without doing anything. I customised two GPIO pins to output on the LCD. It can be switched on without any error during debugging, with the rest of the build identical to the SDK example. I have built a custom .cfx with the correct flash device configurations and QE_bit_config. I am also using an .arp for the flash that is unavailable in the IDE. Debugging SDK example flexspi_nor_polling_transfer is also successful. I understand that using MCUBootUtility is a more simple way to flash but both USB-HID and UART are unavailable options for my board. I only have the option of JTAG through a P&E USB UNIVERSAL FX.  I tried both flashing when the board was boot as serial downloader and internal boot, and tried to boot the board in internal boot mode to see if the LCD is switched on. Is there any flash specific configurations that I still need to alter to make this tool work? Is there any alternative way for flashing?  Thank you. Re: Unable to flash i.MX1052 using MCUXpresso GUI Flash Tool. Thank you for your reply. My colleague just made it work yesterday using Keil and J-link, while I have made very little progress using my set up for the past week. It feels like MCUXpresso's unique toolset still lacks much support and examples in documentations and drivers, but that may just be my lack of experience with this tool. Thank you for your help once again. Kin Re: Unable to flash i.MX1052 using MCUXpresso GUI Flash Tool. Hi @KinC  It seems like you’re dealing with a complex issue involving custom configurations and potential tool limitations. Here are a few things you can check or try to resolve the flashing problem: 1. Verify .arp and .cfx File Configurations: • Ensure that the .arp file you’re using correctly supports the Winbond W25Q512JV flash. Sometimes, custom .arp files might not fully align with the specific requirements of your flash memory or the RT1052. Double-check the configurations, especially the Quad Enable (QE) bit settings. 2. Review Pin Muxing: • Confirm that the custom GPIO pin configurations for the LCD do not conflict with the FLEXSPI pin configurations. Incorrect pin muxing could prevent the flash from being correctly accessed. 3. Check FLEXSPI Settings: • Review the FLEXSPI configuration in your flashloader project to ensure that the settings match the requirements of the W25Q512JV. Incorrect timing or command settings could lead to failed programming. 4. Alternative Flashing Method: • Since you have confirmed that MCUBootUtility is not an option, you can try using the J-Flash tool by SEGGER, which is another robust tool for programming external flash memories. If you have access to a J-Link debugger, you could try this approach. 5. Test with Another Flash Algorithm: • If you suspect the current flash algorithm is not working as expected, try experimenting with other compatible flash algorithms or tweaking the existing one to better suit your setup. 6. Double-Check Boot Mode: • Ensure that the board is correctly configured in the desired boot mode before flashing. This might involve setting specific boot pins or jumpers to ensure the MCU is in the correct state to accept programming. Hope this will help you. BR Hang Re: Unable to flash i.MX1052 using MCUXpresso GUI Flash Tool. Additional Info: I noticed that the Flash tool used  MCUXpressoIDE_11.8.1_1197\ide\plugins\com.pemicro.debug.gdbjtag.pne_5.7.3.202310061729\supportFiles_ARM\target_v7m_vfp instead of my provided .arp to flash the image. Although I have already configured the debug configuration to use my dedicated .arp. The dedicated .arp file will be used to erase the flash memory if I use the GUI Flash tool's 'Erase' function, but it won't use it to flash, which is confusing.  

Schematic / AT-F DTS mismatch on S32G-VNP-RDB3 Evaluation Board I am looking at the schematic and device tree for the arm trusted firmware on the S32G-VNP-RDB3 board and see what looks like a mismatch in netnames and the pinctrl functionality with respect to the PFE pins. This is a pictue from the schematic showing that the RGMII_B_* net pins are labelled as PFE_MAC2_* on the S32G side. Looking at the device tree and cross-referencing the S32G3_IOMUX.xlsx spreedsheet I see that they are actually mapped to PFE_MAC0_* internally.  Here is a snippet from the device tree @ https://github.com/nxp-auto-linux/arm-trusted-firmware/blob/0cd12bb2630a23e760683bf3d911e3c1e282efd5/fdts/s32g.dtsi#L1141C1-L1328C1 And here I added comments to show how the functional groups for the pins map according to the spreadsheet... pfe0_pins: pfe0 { pfe0_grp0 { pinmux = , /* PFE_MAC0_TX_EN_O */ , /* PFE_MAC0_TXD_O[1] */ , /* PFE_MAC0_TXD_O[2] */ , /* PFE_MAC0_TXD_O[3] */ ; /* PFE_MAC0_TXD_O[0] */ output-enable; slew-rate = ; }; pfe0_grp1 { pinmux = , /* GPIO / PFE_MAC0_RX_CLK_I */ , /* GPIO / PFE_MAC0_RXDV_I */ , /* GPIO / PFE_MAC0_RXD_I[0] */ , /* GPIO / PFE_MAC0_RXD_I[1] */ , /* GPIO / PFE_MAC0_RXD_I[2] */ ; /* GPIO / PFE_MAC0_RXD_I[3] */ input-enable; slew-rate = ; }; pfe0_grp2 { pinmux = ; /* PFE_MAC0_TX_CLK_O */ output-enable; slew-rate = ; bias-pull-up; }; pfe0_grp3 { pinmux = , /* GPIO / PFE_MAC0_RX_CLK_I */ , /* GPIO / PFE_MAC0_RXDV_I */ , /* GPIO / PFE_MAC0_RXD_I[0] */ , /* GPIO / PFE_MAC0_RXD_I[1] */ , /* GPIO / PFE_MAC0_RXD_I[2] */ ; /* GPIO / PFE_MAC0_RXD_I[3] */ }; }; So my question is basically are the S32G side nets on the schematic mislabelled and should actually read PFE_MAC0_*? I am using this as the reference for a custom design and want to make sure I have the correct understanding. Thanks. Re: Schematic / AT-F DTS mismatch on S32G-VNP-RDB3 Evaluation Board Hello @minersrevolt , For what I can see you were able to solve your questions. Is that correct? if not, please let us know the exact open points or doubts you might still have so we can support you. Thanks Re: Schematic / AT-F DTS mismatch on S32G-VNP-RDB3 Evaluation Board Looking at the Linux DTS looks like the Functional Groups actually match MAC2 so it is just the AT-F that is out of sync. https://github.com/nxp-auto-linux/linux/blob/adceb7e8fa72c4f26207356a5a33b55b0838717f/arch/arm64/boot/dts/freescale/s32gxxxa-rdb.dtsi#L341C1-L398C4 pfe2mdiob_pins: pfe2mdiob_pins { pfe2mdiob_grp0 { pinmux = ; output-enable; slew-rate = ; }; pfe2mdiob_grp1 { pinmux = ; output-enable; input-enable; slew-rate = ; }; pfe2mdiob_grp2 { pinmux = ; }; }; pfe2rgmiib_pins: pfe2rgmiib_pins { pfe2rgmiib_grp0 { pinmux = , , , , ; output-enable; slew-rate = ; }; pfe2rgmiib_grp1 { pinmux = , , , , , ; input-enable; slew-rate = ; }; pfe2rgmiib_grp2 { pinmux = , , , , , , ; }; pfe2rgmiib_grp3 { pinmux = ; output-enable; slew-rate = ; bias-pull-up; }; };

SE050:缶n.c.ピンはグランドに接続されていますか? こんにちは SE050について: N.C.(未接続)のピンは全てVss(グランド)に接続できますか? データシートには明記されておらず、評価ボード上で浮いたままになっているため、質問する必要があります。 私のデザインは浮遊金属を必要としません。