HID(W): LIBUSB_ERROR_TIMEOUT (-7) FRDM i.MX 93 Good Morning ! I am trying to get ready with FRDM i.MX 93 with getting started guide: Guide I downloaded FRDM-IMX93 Demo Images (tried REV.1.0 and REV4.0), but keep getting same error message. Tried command from guide: .\uuu.exe -b sd_all imx-image-full-imx93frdm.rootfs.wic.zst uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.5.243-0-g230f1b1 Build in config: Pctl Chip Vid Pid BcdVersion Serial_No ================================================== SDPS: MX8QXP 0x1fc9 0x012f [0x0002..0xffff] SDPS: MX8QM 0x1fc9 0x0129 [0x0002..0xffff] SDPS: MX8DXL 0x1fc9 0x0147 SDPS: MX28 0x15a2 0x004f SDPS: MX815 0x1fc9 0x013e SDPS: MX865 0x1fc9 0x0146 SDPS: MX8ULP 0x1fc9 0x014a SDPS: MX8ULP 0x1fc9 0x014b SDPS: MX93 0x1fc9 0x014e SDPS: MX91 0x1fc9 0x0159 SDPS: MX95 0x1fc9 0x015d SDPS: MX95 0x1fc9 0x015c SDPS: MX943 0x1fc9 0x0027 SDPS: MX952 0x1fc9 0x0028 SDP: MX7D 0x15a2 0x0076 SDP: MX6Q 0x15a2 0x0054 SDP: MX6D 0x15a2 0x0061 SDP: MX6SL 0x15a2 0x0063 SDP: MX6SX 0x15a2 0x0071 SDP: MX6UL 0x15a2 0x007d SDP: MX6ULL 0x15a2 0x0080 SDP: MX6SLL 0x1fc9 0x0128 SDP: MX7ULP 0x1fc9 0x0126 SDP: MXRT106X 0x1fc9 0x0135 SDP: MX8MM 0x1fc9 0x0134 SDP: MX8MQ 0x1fc9 0x012b SDPU: SPL 0x0525 0xb4a4 [0x0000..0x04ff] SDPV: SPL1 0x0525 0xb4a4 [0x0500..0x9998] SDPV: SPL1 0x1fc9 0x0151 [0x0500..0x9998] SDPU: SPL 0x0525 0xb4a4 [0x9999..0x9999] SDPU: SPL 0x3016 0x1001 [0x0000..0x04ff] SDPV: SPL1 0x3016 0x1001 [0x0500..0x9998] FBK: 0x066f 0x9afe FBK: 0x066f 0x9bff FBK: 0x1fc9 0x0153 FB: 0x0525 0xa4a5 FB: 0x18d1 0x0d02 FB: 0x3016 0x0001 FB: 0x1fc9 0x0152 FB: 0x0483 0x0afb Run built-in script: uuu_version 1.4.149 # @_flash.bin | bootloader, which can extract from wic image # @_image [_flash.bin] | wic image burn to emmc. # This command will be run when i.MX6/7 i.MX8MM, i.MX8MQ SDP: boot -f imx-image-full-imx93frdm.rootfs.wic.zst/* -scanlimited 0x800000 # This command will be run when ROM support stream mode # i.MX8QXP, i.MX8QM SDPS: boot -scanterm -f imx-image-full-imx93frdm.rootfs.wic.zst/* -scanlimited 0x800000 # These commands will be run when use SPL and will be skipped if no spl # SDPU will be deprecated. please use SDPV instead of SDPU # { SDPU: delay 1000 SDPU: write -f imx-image-full-imx93frdm.rootfs.wic.zst/* -offset 0x57c00 -scanlimited 0x800000 SDPU: jump -scanlimited 0x800000 # } # These commands will be run when use SPL and will be skipped if no spl # if (SPL support SDPV) # { SDPV: delay 1000 SDPV: write -f imx-image-full-imx93frdm.rootfs.wic.zst/* -skipspl -scanterm -scanlimited 0x800000 SDPV: jump -scanlimited 0x800000 # } FB: ucmd setenv fastboot_dev mmc FB: ucmd setenv mmcdev ${sd_dev} FB: ucmd mmc dev ${sd_dev} FB: flash -raw2sparse all imx-image-full-imx93frdm.rootfs.wic.zst/* FB: flash -scanterm -scanlimited 0x800000 bootloader imx-image-full-imx93frdm.rootfs.wic.zst/* FB: done Wait for Known USB Device Appear... New USB Device Attached at 4:2-23F11C6A09B54230 4:2-23F11C6A09B54230>Start Cmd:SDPS: boot -scanterm -f imx-image-full-imx93frdm.rootfs.wic.zst/* -scanlimited 0x800000 Decompress file:>imx-image-full-imx93frdm.rootfs.wic.zst 14%4:2-23F11C6A09B54230>Fail HID(W): LIBUSB_ERROR_TIMEOUT (-7)(20.15s) Then I tried .\uuu.exe -v -b emmc_all .\imx-boot-imx93frdm-sd.bin-flash_singleboot .\imx-image-full-imx93frdm.rootfs.wic.zst, but also got same error meassage: uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.5.243-0-g230f1b1 Build in config: Pctl Chip Vid Pid BcdVersion Serial_No ================================================== SDPS: MX8QXP 0x1fc9 0x012f [0x0002..0xffff] SDPS: MX8QM 0x1fc9 0x0129 [0x0002..0xffff] SDPS: MX8DXL 0x1fc9 0x0147 SDPS: MX28 0x15a2 0x004f SDPS: MX815 0x1fc9 0x013e SDPS: MX865 0x1fc9 0x0146 SDPS: MX8ULP 0x1fc9 0x014a SDPS: MX8ULP 0x1fc9 0x014b SDPS: MX93 0x1fc9 0x014e SDPS: MX91 0x1fc9 0x0159 SDPS: MX95 0x1fc9 0x015d SDPS: MX95 0x1fc9 0x015c SDPS: MX943 0x1fc9 0x0027 SDPS: MX952 0x1fc9 0x0028 SDP: MX7D 0x15a2 0x0076 SDP: MX6Q 0x15a2 0x0054 SDP: MX6D 0x15a2 0x0061 SDP: MX6SL 0x15a2 0x0063 SDP: MX6SX 0x15a2 0x0071 SDP: MX6UL 0x15a2 0x007d SDP: MX6ULL 0x15a2 0x0080 SDP: MX6SLL 0x1fc9 0x0128 SDP: MX7ULP 0x1fc9 0x0126 SDP: MXRT106X 0x1fc9 0x0135 SDP: MX8MM 0x1fc9 0x0134 SDP: MX8MQ 0x1fc9 0x012b SDPU: SPL 0x0525 0xb4a4 [0x0000..0x04ff] SDPV: SPL1 0x0525 0xb4a4 [0x0500..0x9998] SDPV: SPL1 0x1fc9 0x0151 [0x0500..0x9998] SDPU: SPL 0x0525 0xb4a4 [0x9999..0x9999] SDPU: SPL 0x3016 0x1001 [0x0000..0x04ff] SDPV: SPL1 0x3016 0x1001 [0x0500..0x9998] FBK: 0x066f 0x9afe FBK: 0x066f 0x9bff FBK: 0x1fc9 0x0153 FB: 0x0525 0xa4a5 FB: 0x18d1 0x0d02 FB: 0x3016 0x0001 FB: 0x1fc9 0x0152 FB: 0x0483 0x0afb Run built-in script: uuu_version 1.4.149 # @_flash.bin | bootloader, which can extract from wic image # @_image [_flash.bin] | wic image burn to emmc. # This command will be run when i.MX6/7 i.MX8MM, i.MX8MQ SDP: boot -f .\imx-boot-imx93frdm-sd.bin-flash_singleboot -scanlimited 0x800000 # This command will be run when ROM support stream mode # i.MX8QXP, i.MX8QM SDPS: boot -scanterm -f .\imx-boot-imx93frdm-sd.bin-flash_singleboot -scanlimited 0x800000 # These commands will be run when use SPL and will be skipped if no spl # SDPU will be deprecated. please use SDPV instead of SDPU # { SDPU: delay 1000 SDPU: write -f .\imx-boot-imx93frdm-sd.bin-flash_singleboot -offset 0x57c00 SDPU: jump -scanlimited 0x800000 # } # These commands will be run when use SPL and will be skipped if no spl # if (SPL support SDPV) # { SDPV: delay 1000 SDPV: write -f .\imx-boot-imx93frdm-sd.bin-flash_singleboot -skipspl -scanterm -scanlimited 0x800000 SDPV: jump -scanlimited 0x800000 # } FB: ucmd setenv fastboot_dev mmc FB: ucmd setenv mmcdev ${emmc_dev} FB: ucmd mmc dev ${emmc_dev} FB: flash -raw2sparse all .\imx-image-full-imx93frdm.rootfs.wic.zst/* FB: flash -scanterm -scanlimited 0x800000 bootloader .\imx-boot-imx93frdm-sd.bin-flash_singleboot FB: ucmd if env exists emmc_ack; then ; else setenv emmc_ack 0; fi; FB: ucmd mmc partconf ${emmc_dev} ${emmc_ack} 1 0 FB: done Wait for Known USB Device Appear... New USB Device Attached at 4:2- 4:2->Start Cmd:SDPS: boot -scanterm -f .\imx-boot-imx93frdm-sd.bin-flash_singleboot -scanlimited 0x800000 4:2->Fail HID(W): LIBUSB_ERROR_TIMEOUT (-7)(20.02s) I am using latest uuu.exe version. Also with new drivers on windows. Re: HID(W): LIBUSB_ERROR_TIMEOUT (-7) FRDM i.MX 93 Same here. I'm trying with Ubuntu 20.04 and same error occured. sudo ~/uuu-ubuntu20.04 -lsusb uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.5.243-0-g230f1b1 Connected Known USB Devices Path Chip Pro Vid Pid BcdVersion Serial_no ==================================================================== 1:3 MX93 SDPS: 0x1FC9 0x014E 0x0001 8214D79A2FFA4708 sudo ~/uuu-ubuntu20.04 -b emmc_all imx-boot-imx93-11x11-lpddr4x-frdm-sd.bin-flash_singleboot imx-image-core-imx93-11x11-lpddr4x-frdm.rootfs-20260608162024.wic.zst uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.5.243-0-g230f1b1 Success 0 Failure 1 1:3-8214D79A 1/ 1 [HID(W): LIBUSB_ERROR_TIMEOUT (-7) ] SDPS: boot -scanterm -f imx-boot-imx93-11x11-lpddr4x-frdm-sd.bin-flash... I tried both with MACHINE=imx93frdm and MACHINE=imx93-11x11-lpddr4x-frdm and same result. I just see this log on UART DEBUG: U-Boot SPL 2024.04+gde16f4f1722+p0 (Sep 02 2024 - 10:44:35 +0000) SOC: 0xa1009300 LC: 0x2040010 PMIC: PCA9451A PMIC: Over Drive Voltage Mode DDR: 3733MTS DDR: 3733MTS M33 prepare ok There's no solution anywhere and no one is helping. Re: HID(W): LIBUSB_ERROR_TIMEOUT (-7) FRDM i.MX 93 Hello, Please try with the standard BSP release from here: https://www.nxp.com/design/design-center/software/embedded-software/i-mx-software/embedded-linux-for-i-mx-applications-processors:IMXLINUX Also, I would rather recommend to not use the compressed rootfs, please uncompress (un-zst) and try again. Best regards/Saludos, Aldo. Re: HID(W): LIBUSB_ERROR_TIMEOUT (-7) FRDM i.MX 93 Hi, I am facing the same problem.
The board is booting fine from the emmc but when I try to flash the SD card in any way it does not work.
I tried flashing one of the pre-built images on the imx93 FRDM main page (compressed and un-compressed)
using uuu
I also used dd:
zstd -d imx-image-full-imx93frdm.rootfs.wic.zst -c | sudo dd of=/dev/mmcblk0 bs=4M status=progress conv=fsync
then when I boot the board from the SD card it does not fully boot and stops there
U-Boot SPL 2024.04+gde16f4f1722+p0 (Sep 02 2024 - 10:44:35 +0000)
SOC: 0xa1009300
LC: 0x2040010
PMIC: PCA9451A
PMIC: Over Drive Voltage Mode
DDR: 3733MTS
DDR: 3733MTS
M33 prepare ok
And I faced this same output after booting up when I tried flashing the SD card with the Debian-based image using flex-installer. Re: HID(W): LIBUSB_ERROR_TIMEOUT (-7) FRDM i.MX 93 Hello!!
For the first issue, please note that you'll need the bootloader not only the rootfs, so you'll need to run a command like the following: ./uuu -b emmc_all flash.bin imx-image-full-imx93frdm.rootfs.wic
For the issue that it uses dd, is the same please do not use compressed rootfs (un-zst)
Best regards/Saludos, Aldo. Re: HID(W): LIBUSB_ERROR_TIMEOUT (-7) FRDM i.MX 93 Also please update the guide I linked in first post to help others :). Re: HID(W): LIBUSB_ERROR_TIMEOUT (-7) FRDM i.MX 93 Hello, Glad that it is now working, I will double check the script maybe it uses a different bootloader, and yes we are working on improvingthe documentation for the FRDM boards we apreciate your comments. Best regards/Saludos, Aldo. Re: HID(W): LIBUSB_ERROR_TIMEOUT (-7) FRDM i.MX 93 Well I think it worked with the latest software You linked and command: .\uuu.exe -v uuu.auto-imx93-11x11-lpddr4x-frdm But I don't know is it the best solution, because now my board introduces itself as "imx93evk" not imx93frdm. Re: HID(W): LIBUSB_ERROR_TIMEOUT (-7) FRDM i.MX 93 As I told it is not working, check my comment above. The only way to make it work is: .\uuu.exe -v uuu.auto-imx93-11x11-lpddr4x-frdm Re: HID(W): LIBUSB_ERROR_TIMEOUT (-7) FRDM i.MX 93 Hi, I have run into this problem as well, trying out a i.MX 93 FRDM development board. The training guide I found was wrong and misleading, the demo firmware package contains a pile of files with no info as to what each one is, and the usage of the "uuu" utility is almost incomprehensible (at least to me!), even after reading the manual for it. Here's what I have figured out. Someone please correct me if I got this wrong. I downloaded the demo firmware package "LF_v6.18.20-2.0.0_images_IMX93EVK.zip". I wanted to test the process of writing a firmware image to the uSD card and/or the built-in eMMC. Here is what worked: * I think files with names like "imx-boot-imx93-11x11-lpddr4x-frdm-sd.bin-flash_singleboot" are bootloader images for specific boards and different configurations. I chose this one for writing to uSD card on my board. * I think "imx-image-full-imx93evk.wic" is the Linux image (rootfs, etc). There is only one, so I guess it's the same for all supported dev boards? * As per comments above, don't try to use the zipped version "imx-image-full-imx93evk.tar.zst"? To write to uSD card: * Power off board * Insert uSD card * Connect board "USB1_C" port to laptop via USB-C cable * Set boot switches to [3:0] 0001 for serial download mode * Use this uuu command from the firmware folder: # Copy BOOTLOADER ONLY to the SD card: uuu -b sd imx-boot-imx93-11x11-lpddr4x-frdm-sd.bin-flash_singleboot # OR: Copy bootloader and linux image: uuu -b sd_all imx-boot-imx93-11x11-lpddr4x-frdm-sd.bin-flash_singleboot imx-image-full-imx93evk.wic * Power on the board. UUU should automatically detect the board and start the download. For writing the files to eMMC, you use these commands: # Bootloader Only: uuu -b emcc imx-boot-imx93-11x11-lpddr4x-frdm-sd.bin-flash_singleboot # OR: Bootloader and Image: uuu -b emmc_all imx-boot-imx93-11x11-lpddr4x-frdm-sd.bin-flash_singleboot imx-image-full-imx93evk.wic I don't know what the difference is between the various boot loader files. @Kapixxx Your method probably did work. I think all the boards use the same Linux rootfs so they all have the host name "imx93evk". However, I have not figured out how to use a uuu script (e.g. "uuu.auto-imx93-11x11-lpddr4x-frdm") to write to uSD card rather than eMMC. The relationship between the supplied command line parameters, built-in scripts, and supplied script files is unclear.
查看全文
