Multi Source Translation Content

cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 

Multi Source Translation Content

Discussions

Sort by:
S32DS 3.5のライセンス延長申請 こんにちは、 私のS32 Design Studioのライセンスがもうすぐ切れる。延長を手伝ってもらえますか? アクティベーションID: 5E5E-87D6-4F85-9A22 バージョン: 3.5 よろしくお願い申し上げます。 製品に適用されるライセンス: バージョン説明 3.5S32 プラットフォーム v.3.5 Design Studio ライセンス数:1 フルフィルメントID:201997687 有効期限:2026年11月4日 製品:S32 プラットフォーム v.3.5用 S32 Design Studio 機械: 6EF78E1197D8A04DBC0B058E7DE51D3F39A0F67C アクティベーションコード:5E5E-87D6-4F85-9A22
View full article
FS26 can't enter LPOFF/StandBy state We use the infineon MCU TC37x With FS26 SBC. when request power down, SBC can't entry LPOFF/StandBy mode from Normal mode. the request command is normal, but sbc still in normal mode. I want to know which conditions prevent the state transform? Re: FS26 can't enter LPOFF/StandBy state Hi Liu, Please check the following: 1. Confirm the fail-safe state before requesting low-power mode The low-power transition shown in the state diagram starts from the fail-safe Normal mode. Before sending the request, please read: FS_STATES at address 0x57 FS_DIAG_SAFETY1 at address 0x54 FS_DIAG_SAFETY2 at address 0x55 FS_OVUV_REG_STATUS at address 0x50 FS_STATES[4:0] = 0x0B indicates that the fail-safe state machine is in Normal mode. The diagnostic registers can also show whether a watchdog, SPI, FCCU, ERRMON, BIST or voltage-monitoring event has occurred. 2. Verify the complete two-step command sequence For LPOFF mode, write the following values to FS_LP_REQ at address 0x58: FS_LP_REQ[7:0] = 0xA5, which requests Pre-LPOFF mode. FS_LP_REQ[7:0] = 0x5A, which completes the transition to LPOFF mode. For Standby mode, the corresponding sequence is: 0xAA, which requests Pre-Standby mode. 0x55, which completes the transition to Standby mode. The second command must be received within 10 ms of the first. Please send the two commands back-to-back and confirm that both SPI frames use the correct fail-safe register selection, address, CRC and number of clock cycles. If the second command is missing, invalid or not received within the required interval, the requested low-power transition will not be completed.  3. Check for SPI errors Immediately after the first request, check FS_DIAG_SAFETY1 for: SPI_FS_CLK SPI_FS_REQ SPI_FS_CRC These bits indicate an incorrect number of SPI clocks, an invalid fail-safe SPI access, or a CRC error. Any of these conditions can explain why the low-power command was not accepted. 4. Exclude an immediate wake-up An enabled wake-up source that is already active, or that becomes active during the transition, can make the device wake up immediately and therefore appear to remain in Normal mode. Please check M_WIO_CFG for the enabled wake-up sources and their configured polarities: WAKE1 and WAKE2 GPIO1 and GPIO2 LDT SPI CSB transition In particular, if CSBWUEN = 1, subsequent SPI activity can wake the FS26 through a high-to-low CSB transition. After the device wakes up, M_WIO_FLG.WUEVENT[3:0] can be read to identify the detected wake-up source. Finally, please note that VPRE remains enabled in Standby mode and LDO1 or LDO2 may also remain enabled depending on the OTP configuration. Therefore, the presence of these rails alone does not prove that the FS26 remained in Normal mode. In LPOFF, the regulators are switched off and RSTB is low. BRs, Tomas
View full article
country of origin of S32Z280ABCK0MJFT which is the COO of S32Z280ABCK0MJFT Re: country of origin of S32Z280ABCK0MJFT Please, contact export control team at: [email protected] for more information.
View full article
MKW38 BLE Scan not working when long time test Dear Christine Li and NXP team   Thank your for support   Following up on the BLE scan issue we reported earlier, we would like to share additional analysis results from our long-run test and ask a few questions.     1. Summary During continuous scanning, the controller sometimes stops delivering any LE Advertising Reports to the host. During this period, the LL registers show that scanning is still active (SCAN_STATUS.Scan_on = 1), but no packet is received at all. PKT_RSSI_STATUS and CH_ADDR do not change. In most cases the controller recovers by itself within 1 s – 2.5 min. In one case it never recovered (more than 8 hours, until the log ended). We were informed that SDK 2.6.916 fixes this issue. However, the issue was reproduced within about one week with the SDK 2.6.916 libraries. Test conditions   Units / duration: 5 units, approx. 14.6 days each, no MCU reset during the test Controller library: imported in Apr 2023, 2.6.615 or later (contains Controller_SetPeripheralDiscThreshold(); exact version unknown) lib_ble_kw38a4_controller_gcc.a, 617,384 bytes, MD5 prefix 50417a8d65 Separate test: SDK 2.6.916 libraries – same symptom reproduced within about 1 week Scan parameters: Active scan, interval 0x0011 (10.625 ms), window 0x0008 (5 ms) Filter policy: accept all, duplicate filtering disabled Continuous scanning (gGapScanContinuously_d), extended scanning (scanning PHY register 0x14E = 0x0005) Scan start/stop: started once after boot; no scan stop/start during the test Environment: approx. 75–110 advertising reports per second in normal operation Application-side register access: Read-only polling of LL registers every 1 s (0x01C, 0x01E, 0x064, 0x0C4, 0x0D2, 0x0D4, 0xF28) One 16-bit read of INIT_SCN_ADV_RX_FIFO (0x4008007C) every 180 s for diagnostics No LL register is written by the application 3. How we detect the issue We count advertising reports at each layer every second: L1: LE (Extended) Advertising Report events passed from the controller to the host. Counted in a wrapper around Ble_HciRecv() registered with Controller_Init(). L2: gDeviceScanned_c / gExtDeviceScanned_c delivered to the application callback. L4: Reports processed by the application task. When the issue occurs, all counters stop at L1. The controller stops generating advertising reports. Host and application are not involved: Ble_HciRecv() reports no failure at that time. Application message allocation does not fail. The application queue is empty. 4. Statistics (5 units, approx. 14.6 days) Unit #1: 8 stall events, 8 recovered (duration 11 – 35 s) Unit #2: 9 stall events, 8 recovered (duration 11 – 159 s); last event not recovered (> 8 h) Unit #3: 7 stall events, 7 recovered (duration 11 – 78 s) Unit #4: 2 stall events, 2 recovered (duration 11 – 30 s) Unit #5: 3 stall events, 3 recovered (duration 12 – 14 s) Total: 29 stall events, 28 recovered (Duration includes the 10 s detection time.) Key observation: In all 28 recovered events, the last received packet before the stall was on a secondary advertising channel. The CH_ADDR RX index was one of 0x06, 0x0A, 0x0C, 0x0E, 0x10, 0x12, 0x14, 0x16, 0x1E, 0x22, 0x26, 0x28, 0x2A, 0x30, 0x3E, 0x4A. In most cases PKT_PAYLOAD_STATUS = 0x0007, i.e. a 7-byte payload. This suggests the stall starts right after receiving an AUX packet. In the non-recovered event, the last received packet was on primary channel 37 (CH_ADDR = 0x0018, PKT_PAYLOAD_STATUS = 0x0025). 5. Register snapshot of the non-recovered event (unit #2)  -SCAN_STATUS(0x01C) = 0x0900 (Scan_on = 1, no pending interrupt)  -SCAN_NEXT_INSTANT(0x01E) = 0xB4B7  -REF_CLK(0x064) = 0xB4AD  -CH_ADDR(0x0C4) = 0x0018  -PKT_PAYLOAD_STATUS(0x0D2) = 0x0025  -PKT_RSSI_STATUS(0x0D4) = 0x3FB3  -SCAN_SYNC_RX_PKT_CNT(0xF28) = 0x0000   SCAN_STATUS, CH_ADDR, PKT_RSSI_STATUS and SCAN_SYNC_RX_PKT_CNT stayed unchanged for more than 8 hours. The L1 report counter also stayed constant during this period. 6. Release note review The only scan-related item in SDK 2.6.212 – 2.6.916 is in 2.6.815. Link Layer fixes/changes by version: 2.6.212 (ble_controller 1.6.11.1): No changes 2.6.415 (2022-05, 1.6.14): Host fixes only 2.6.615 (2023-02, 1.6.14.1): Premature ACL termination option (Controller_SetPeripheralDiscThreshold) 2.6.715 (2023-03, 1.6.14.3): MD bit handling 2.6.815 (2023-05, 1.6.14.4): Channel map fix; “Fixed a Scan issue causing Advertising to be missed for some cases.” 2.6.915 (2023-09, 1.6.14.5): EnhancedNotification alignment fix; Autonomous Length Procedure disabled 2.6.916 (2023-10, 1.6.14.6): Return unmapped ChannelNumber in EnhancedNotification (Algo #1) 7. Questions Is this a known issue of the KW38 BLE controller? Is it related to the 2.6.815 fix “Scan issue causing Advertising to be missed”? If so, could you describe the exact condition that was fixed? Can extended scanning (following an AUX pointer to a secondary channel) put the LL scanner into a state where it no longer receives on any channel while SCAN_STATUS.Scan_on stays 1? Since the issue was reproduced with SDK 2.6.916, is there a newer controller library or patch that addresses it? What is the recommended way to detect and recover from this state at application level? For example: Is Gap_StopScanning() / Gap_StartScanning() sufficient? Is a controller reset required (e.g. HCI Reset or the LL SOFT_RESET command)? Is there any LL status register we should check? Would disabling extended scanning (legacy scanning only) avoid this issue? Is it allowed to read INIT_SCN_ADV_RX_FIFO (0x4008007C) from the application for diagnostics? Could this read affect the controller’s FIFO handling? Re: MKW38 BLE Scan not working when long time test Key observations: [modified] -In all 28 recovered events, the last received packet was on a secondary advertising channel, and in most cases PKT_PAYLOAD_STATUS = 0x0007 (7-byte payload, typical of an extended advertising PDU carrying an AuxPtr). This suggests these stalls start while the scanner follows an AUX pointer. -The non-recovered event (unit #2) has a different signature: the last received packet was on primary channel 37 with a 37-byte payload (PKT_PAYLOAD_STATUS = 0x0025), i.e. most likely a legacy advertising PDU. We found no indication of extended advertising involvement in this case. INIT_SCN_ADV_RX_FIFO read as 0 every 3 minutes during the stall, and the controller did not recover for more than 8 hours. Re: MKW38 BLE Scan not working when long time test Note: In an earlier firmware, the application periodically wrote 0xFFFF to SCAN_INTR_CLEAR (0x4008001C). In that firmware we observed a different stall where INIT_SCN_ADV_RX_FIFO still held data while SCAN_SYNC_RX_PKT_CNT was 0, and reading 0x4008007C once via J-Link immediately recovered scanning. We have since removed that write. The statistics in this report are from the current firmware, where the FIFO reads 0 during the stall and reading it does not affect recovery. Re: MKW38 BLE Scan not working when long time test Hi, @JungkyuHan1  Thanks for creating new case to us. I will check the detailed info and updates to you ASAP. BR, Christine. Re: MKW38 BLE Scan not working when long time test Hi, @JungkyuHan1  Please allow me some more time to reply to you.  I need to check some points with our internal team. BR, Christine. Re: MKW38 BLE Scan not working when long time test Hi, @JungkyuHan1  If I am correct, I received your email that mentioned " We have conducted the BLE Scan test With the SDK 2.6.916. It works pretty well. There was no scan error for more than 8days." in the December of 2025.  But now you meet this issue: "However, the issue was reproduced within about one week with the SDK 2.6.916 libraries." May I ask whether have any test differences between these OK and NOK cases? If we know the differences, it will be really helpful for us to track it further. For your questions: Is this a known issue of the KW38 BLE controller? Is it related to the 2.6.815 fix “Scan issue causing Advertising to be missed”? If so, could you describe the exact condition that was fixed? ==>[Christine]: As our communicated before, yes, it is a known issue. And as we know,  the 2.6..916 is the version I know so far that at least have a work around can help on scan issue. As far as I know, the scan issue is because an conflict on scan FIFO, so it needs flush the scan FIFO.  Can extended scanning (following an AUX pointer to a secondary channel) put the LL scanner into a state where it no longer receives on any channel while SCAN_STATUS.Scan_on stays 1? Since the issue was reproduced with SDK 2.6.916, is there a newer controller library or patch that addresses it? ==>[Christine]:Sorry, no we do not have other newer SDK release which fixed this issue than SDK 2.6.916. What is the recommended way to detect and recover from this state at application level? For example: Is Gap_StopScanning() / Gap_StartScanning() sufficient? Is a controller reset required (e.g. HCI Reset or the LL SOFT_RESET command)? Is there any LL status register we should check? ==>[Christine]: The workaround you may need manually add in applicaiton code as below there should have an function ll_flush_adv_rx_fifo(). The code by this function does not exist in applicaiton code, so you need use "extern" declare it . After externing this function, the input parameter and return value are both void, and then call: 1. Call before stopping scan every time 2. If the device is not scanned for a long time, stop scanning and call it again, than start scaning. Would disabling extended scanning (legacy scanning only) avoid this issue? Is it allowed to read INIT_SCN_ADV_RX_FIFO (0x4008007C) from the application for diagnostics? Could this read affect the controller’s FIFO handling? ==>[Christine]:For these 2 questions, let me check further then reply to you.   BR, Christine. Re: MKW38 BLE Scan not working when long time test Hi Christine, Thank you for your reply. Regarding the difference between the OK case (December 2025) and the NOK case: We found a mistake in our SDK 2.6.916 migration. We are now re-testing with the correct SDK 2.6.916 libraries. The test setups were also different: Previous test (OK): 3 units (2 sample units and 1 development unit), without antennas. Current test: 5 new mass-production units, all with antennas installed. We also have some additional questions: Is the 2.6.815 fix “Fixed a Scan issue causing Advertising to be missed for some cases” the same fix as the scan FIFO lockup workaround (ll_flush_adv_rx_fifo()) in SDK 2.6.916? After the flush, the scan is restarted with the legacy START_SCAN command (0x42). When extended scanning is enabled, does AUX (secondary channel) reception resume correctly after this restart? Is it safe to call ll_flush_adv_rx_fifo() directly from an application task while the controller ISR is running? Is there any concurrency or synchronization issue with the controller’s scan interrupt handling? In the SDK 2.6.615 controller library, what is the meaning of bit 0 of ll_self_device_data[18]? (We are considering applying the same flush manually on 2.6.615.) Best regards, Jungkyu Han Re: MKW38 BLE Scan not working when long time test Hi, @JungkyuHan1  Thanks for the info. I am still checking with our internal team to get the answers for your questions. Once have any updates, I will let you know. BR, Christine. Re: MKW38 BLE Scan not working when long time test Hi, @JungkyuHan1  Below is our internal team's reply, for your referrence. 1. Would disabling extended scanning (legacy scanning only) avoid this issue? [NXP]: The answer is no, although we not test this case, but it should no relate to extended scanning. 2.Is it allowed to read INIT_SCN_ADV_RX_FIFO (0x4008007C) from the application for diagnostics? Could this read affect the controller’s FIFO handling? [NXP]: It's better not read from applicaiton side in any time, you can stop scanning first, then read it and start scanning again 3.Is the 2.6.815 fix “Fixed a Scan issue causing Advertising to be missed for some cases” the same fix as the scan FIFO lockup workaround (ll_flush_adv_rx_fifo()) in SDK 2.6.916? [NXP]: I'm not sure for now, need some time to investigate it. 4.After the flush, the scan is restarted with the legacy START_SCAN command (0x42). When extended scanning is enabled, does AUX (secondary channel) reception resume correctly after this restart? [NXP]: Yes. But you need to follow this process, stop scanning > ll_flush_adv_rx_fifo() > start scaning again. 5.Is it safe to call ll_flush_adv_rx_fifo() directly from an application task while the controller ISR is running? [NXP]: As mentioned in above, it better call ll_flush_adv_rx_fifo() when you stop the scanning 6.Is there any concurrency or synchronization issue with the controller’s scan interrupt handling? [NXP]: what do you mean concurrency or synchronization issue ? can you clarify it? If do as mentioned above, stop scan and flush, then re-start the scan, I do not think it will causing any concurrency or synchronization issue.  7.Can extended scanning (following an AUX pointer to a secondary channel) put the LL scanner into a state where it no longer receives on any channel while SCAN_STATUS.Scan_on stays 1? [NXP]: So far, we not observe such issue. BR, Christine. Re: MKW38 BLE Scan not working when long time test Hi, @JungkyuHan1  3.Is the 2.6.815 fix “Fixed a Scan issue causing Advertising to be missed for some cases” the same fix as the scan FIFO lockup workaround (ll_flush_adv_rx_fifo()) in SDK 2.6.916? [NXP]: Not same, but have correlation, the fix in 2.6.815 not enough for scan FIFO lockup workaround, so that fix no completely fix the scan fifo issue, so better add that workaround. Please let me know if still have any other concerns in this thread. BR, Christine.
View full article
MKW38 BLE 扫描在长时间测试后无法工作 尊敬的 Christine Li 和 NXP 团队   感谢您的支持   针对我们之前报告的 BLE 扫描问题,我们想分享我们长期测试的更多分析结果,并提出一些问题。     1. 总结 在连续扫描期间,控制器有时会停止向主机发送任何 LE 广告报告。 在此期间,LL 寄存器显示扫描仍在进行中(SCAN_STATUS.Scan_on = 1),但根本没有收到任何数据包。PKT_RSSI_STATUS 和 CH_ADDR 不会改变。 大多数情况下,控制器会在 1 秒至 2.5 分钟内自行恢复。其中一次,它始终未能恢复(超过 8 小时,直到日志结束)。 我们获悉 SDK 2.6.916修复了此问题。但是,使用 SDK 2.6.916 库大约一周后,该问题再次出现。 测试条件   单元数/持续时间:约 5 个单元每次测试持续14.6天,测试期间MCU未发生RESET。 控制器库:于 2023 年 4 月导入,版本为 2.6.615 或更高版本(包含 Controller_SetPeripheralDiscThreshold();确切版本未知) lib_ble_kw38a4_controller_gcc.a,617,384 字节,MD5 前缀 50417a8d65 单独测试: SDK 2.6.916图书馆 – 大约一周内出现相同症状。 扫描参数: 活动扫描,间隔 0x0011 (10.625 毫秒),窗口 0x0008 (5 毫秒) 筛选策略:全部接受,禁用重复项筛选 连续扫描(gGapScanContinuously_d),扩展扫描(扫描 PHY 寄存器 0x14E = 0x0005) 扫描启动/停止:启动后启动一次;测试期间不进行扫描停止/启动。 环境:约正常运行时每秒发送 75-110 条广告报告 应用层寄存器访问: 每隔 1 秒对 LL 寄存器进行只读轮询(0x01C、0x01E、0x064、0x0C4、0x0D2、0x0D4、0xF28) 每隔 180 秒对 INIT_SCN_ADV_RX_FIFO (0x4008007C) 进行一次 16 位读取,用于诊断。 应用程序不会写入任何LL注册表。 3. 我们如何检测问题 我们每秒都会统计每一层的广告报告数量: L1: LE(扩展)广告报告事件从控制器传递到主机。在通过 Controller_Init() 注册的 Ble_HciRecv() 的包装器中进行计数。 L2: gDeviceScanned_c / gExtDeviceScanned_c 已传递给应用程序回调。 L4:应用程序任务处理的报告。 当出现问题时,所有计数器都停止在 L1。控制器停止生成广告报告。主机和应用程序不参与其中: 当时ble_HciRecv()没有报告任何故障。 应用程序消息分配不会失败。 应用程序队列为空。 4. 统计学(5 个单元,约 100 个学分)14.6天) 单元 1:8 次停滞事件,8 次恢复(持续时间 11 – 35 秒) 单元 #2:9 次失速事件,8 次已恢复(持续时间 11 – 159 秒);最后一次失速事件未恢复(> 8 小时) 单元#3:7次停滞事件,7次恢复(持续时间11-78秒) 单元#4:2次停滞事件,2次恢复(持续时间11-30秒) 单元#5:3次停滞事件,3次恢复(持续时间12-14秒) 总计:29起停滞事件,28起已恢复 (持续时间包含10秒检测时间。) 关键观察结果: 在所有 28 个恢复事件中,停滞之前接收到的最后一个数据包是在辅助广告频道上。CH_ADDR RX 索引为 0x06、0x0A、0x0C、0x0E、0x10、0x12、0x14、0x16、0x1E、0x22、0x26、0x28、0x2A、0x30、0x3E、0x4A 之一。大多数情况下,PKT_PAYLOAD_STATUS = 0x0007,即 7 字节有效载荷。这表明,在接收到 AUX 数据包后,故障立即开始出现。 在未恢复的事件中,最后一个接收到的数据包位于主通道 37上(CH_ADDR = 0x0018,PKT_PAYLOAD_STATUS = 0x0025)。 5. 注册未恢复事件的快照(单元 #2) -SCAN_STATUS(0x01C) = 0x0900 (Scan_on = 1,无待处理的中断) -SCAN_NEXT_INSTANT(0x01E) = 0xB4B7 -REF_CLK(0x064) = 0xB4AD -CH_ADDR(0x0C4) = 0x0018 -PKT_PAYLOAD_STATUS(0x0D2) = 0x0025 -PKT_RSSI_STATUS(0x0D4) = 0x3FB3 -SCAN_SYNC_RX_PKT_CNT(0xF28) = 0x0000   SCAN_STATUS、CH_ADDR、PKT_RSSI_STATUS 和 SCAN_SYNC_RX_PKT_CNT超过 8 小时保持不变。在此期间,L1报告计数器也保持不变。 6. 版本说明回顾 SDK 2.6.212 中唯一与扫描相关的项– 2.6.916 包含在 2.6.815 中。链路层各版本修复/更改: 2.6.212(ble_controller 1.6.11.1):无变化 2.6.415(2022-05,1.6.14):仅主机修复 2.6.615(2023-02,1.6.14.1):提前终止 ACL 选项(Controller_SetPeripheralDiscThreshold) 2.6.715(2023-03,1.6.14.3):MD 位处理 2.6.815(2023-05,1.6.14.4):频道映射修复; “修复了扫描问题,该问题会导致某些情况下广告无法显示。” 2.6.915(2023-09,1.6.14.5):增强通知对齐修复;自主长度程序已禁用 2.6.916(2023-10,1.6.14.6):在增强通知中返回未映射的 ChannelNumber(算法 #1) 7. 问题 这是KW38 BLE控制器的已知问题吗?它与 2.6.815 有关吗?修复“扫描问题导致广告漏播”?如果是这样,您能否详细描述一下具体修复了什么问题? 扩展扫描(跟随 AUX 指针到辅助通道)是否会导致 LL 扫描器进入一种状态,即当SCAN_STATUS.Scan_on保持为 1时,它不再接收任何通道的信号? 由于该问题已在 SDK 2.6.916 中重现,是否有更新的控制器库或补丁可以解决该问题? 在应用层,检测和恢复这种状态的推荐方法是什么?例如: Gap_StopScanning() / Gap_StartScanning() 是否足够? 是否需要RESET控制器(例如,HCI RESET 或 LL SOFT_RESET 命令? 是否有任何LL状态登记册需要查阅? 禁用扩展扫描(仅使用传统扫描)是否可以避免这个问题? 是否允许从应用程序中读取 INIT_SCN_ADV_RX_FIFO (0x4008007C) 以进行诊断?这次读取操作是否会影响控制器的 FIFO 处理? Re: MKW38 BLE Scan not working when long time test 主要观察结果:[已修改] -在所有 28 个恢复事件中,最后一个接收到的数据包位于辅助广告通道上,并且在大多数情况下,PKT_PAYLOAD_STATUS = 0x0007(7 字节有效载荷,是携带 AuxPtr 的扩展广告 PDU 的典型值)。这表明这些卡顿现象是在扫描仪跟随 AUX 指针时开始发生的。 -未恢复的事件(单元 #2)具有不同的签名:最后一个接收到的数据包在主通道 37 上,有效载荷为 37 字节(PKT_PAYLOAD_STATUS = 0x0025),即很可能是一个传统的通告 PDU。我们没有发现任何迹象表明本案涉及大量广告宣传。在系统卡死期间,INIT_SCN_ADV_RX_FIFO 每 3 分钟读取一次为 0,并且控制器超过 8 小时没有恢复。 Re: MKW38 BLE Scan not working when long time test 注意:在早期固件中,应用程序会定期向 SCAN_INTR_CLEAR (0x4008001C) 写入 0xFFFF。 在该固件中,我们观察到不同的停滞情况,即 INIT_SCN_ADV_RX_FIFO 仍然保存着数据,而 SCAN_SYNC_RX_PKT_CNT 为 0,通过 J-Link 读取一次 0x4008007C 后,扫描立即恢复。 我们已删除该条记录。本报告中的统计数据来自当前固件,其中 FIFO 在卡顿期间读取 0,读取 0 不会影响恢复。 Re: MKW38 BLE Scan not working when long time test 你好, @JungkyuHan1 感谢您向我们提交新的案件。 我会尽快核实详细信息并向您汇报最新情况。 BR, Christine。 Re: MKW38 BLE Scan not working when long time test 你好, @JungkyuHan1 请允许我再花些时间回复您。 我需要和内部团队确认一些事项。 BR, Christine。 Re: MKW38 BLE Scan not working when long time test 你好, @JungkyuHan1 如果我理解正确,我收到了您提到“ 我们使用SDK 2.6.916进行了 BLE 扫描测试,效果非常好。超过 8 天没有出现扫描错误。 “2025 年 12 月。” 但现在您遇到了这个问题:“然而,使用 SDK 2.6.916 库大约一周后,该问题再次出现。 ” 请问OK和NOK病例在测试方面是否存在任何差异? 如果我们知道这些差异,对我们进一步追踪它将会非常有帮助。 关于您的问题: 这是KW38 BLE控制器的已知问题吗?它与 2.6.815 有关吗?修复“扫描问题导致广告漏播”?如果是这样,您能否详细描述一下具体修复了什么问题? ==>[Christine]: 正如我们之前沟通的那样,是的,这是一个已知问题。我们知道, 目前我知道的版本 2.6..916 至少有一个变通方法可以帮助解决扫描问题。据我所知,扫描问题是由于扫描 FIFO 冲突引起的,因此需要刷新扫描 FIFO。  扩展扫描(跟随 AUX 指针到辅助通道)是否会导致 LL 扫描器进入一种状态,即当SCAN_STATUS.Scan_on保持为 1时,它不再接收任何通道的信号? 由于该问题已在 SDK 2.6.916 中重现,是否有更新的控制器库或补丁可以解决该问题? ==>[Christine]:抱歉,我们没有比 SDK 2.6.916 更新的 SDK 版本修复此问题。 在应用层,检测和恢复这种状态的推荐方法是什么?例如: Gap_StopScanning() / Gap_StartScanning() 是否足够? 是否需要RESET控制器(例如,HCI RESET 或 LL SOFT_RESET 命令? 是否有任何LL状态登记册需要查阅? ==>[克里斯汀]: 您可能需要手动在应用程序代码中添加以下解决方法 应该有一个函数 ll_flush_adv_rx_fifo()。该函数的代码在应用程序代码中不存在,因此需要使用“extern”声明它。将此函数外部化后,输入参数和返回值均为 void,然后调用: 1.每次停止扫描前都要打电话 2. 如果设备长时间未扫描,请停止扫描并重新呼叫,然后再开始扫描。 禁用扩展扫描(仅使用传统扫描)是否可以避免这个问题? 是否允许从应用程序中读取 INIT_SCN_ADV_RX_FIFO (0x4008007C) 以进行诊断?这次读取操作是否会影响控制器的 FIFO 处理? ==>[Christine]:关于这两个问题,我需要进一步了解后再回复你。   BR, Christine。 Re: MKW38 BLE Scan not working when long time test 嗨,克里斯汀, 感谢您的回复。 关于OK案例(2025年12月)和NOK案例之间的区别: 我们在 SDK 2.6.916 中发现了一个错误迁移。我们现在正在使用正确的 SDK 2.6.916 版本重新进行测试。图书馆。 测试设置也不同: 先前测试(合格):3 个单元(2 个样品单元和 1 个开发单元),无天线。 当前测试:5 台全新量产机型,全部安装天线。 我们还有一些其他问题: 是 2.6.815修复“修复了某些情况下导致广告丢失的扫描问题”是否与 SDK 2.6.916 中的扫描 FIFO 锁定解决方法 (ll_flush_adv_rx_fifo()) 相同? 刷新后,使用传统的 START_SCAN 命令 (0x42) 重新启动扫描。启用扩展扫描后,重启后 AUX(辅助频道)接收是否能正常恢复? 在控制器中断服务例程 (ISR) 运行时,直接从应用程序任务调用 ll_flush_adv_rx_fifo() 是否安全?控制器的扫描中断处理是否存在并发或同步问题? 在 SDK 2.6.615 中控制器库中,ll_self_device_data[18]的第0位是什么意思?(我们正在考虑在2.6.615版本上手动执行相同的刷新操作。) 此致, 韩正奎 Re: MKW38 BLE Scan not working when long time test 你好, @JungkyuHan1 谢谢你提供的信息。 我仍在向我们的内部团队核实,以获取您问题的答案。 如有任何更新,我会通知您。 BR, Christine。 Re: MKW38 BLE Scan not working when long time test 你好, @JungkyuHan1 以下是我们内部团队的回复,供您参考。 1. 禁用扩展扫描(仅使用传统扫描)是否可以避免此问题? [NXP]:答案是否定的,虽然我们没有测试过这种情况,但这应该与扩展扫描无关。 2.是否允许从应用程序中读取 INIT_SCN_ADV_RX_FIFO (0x4008007C) 以进行诊断?这次读取操作是否会影响控制器的 FIFO 处理? [NXP]:最好不要从应用程序端读取数据,可以先停止扫描,读取后再继续扫描。 3.是2.6.815吗?修复“修复了某些情况下导致广告丢失的扫描问题”是否与 SDK 2.6.916 中的扫描 FIFO 锁定解决方法 (ll_flush_adv_rx_fifo()) 相同? [NXP]:目前我还不确定,需要一些时间进行调查。 4.刷新后,使用传统的 START_SCAN 命令 (0x42) 重新启动扫描。启用扩展扫描后,重启后 AUX(辅助频道)接收是否能正常恢复? [NXP]:是的。但您需要按照以下步骤操作:停止扫描 > ll_flush_adv_rx_fifo() > 重新开始扫描。 5.当控制器中断服务例程运行时,直接从应用程序任务调用 ll_flush_adv_rx_fifo() 是否安全? [NXP]:如上所述,最好在停止扫描时调用 ll_flush_adv_rx_fifo() 函数。 6.控制器的扫描中断处理是否存在并发或同步问题? [NXP]:您说的并发或同步问题是什么意思?能否详细说明一下?如果按照上述步骤操作,停止扫描并刷新,然后再重新启动扫描,我认为不会导致任何并发或同步问题。 7.扩展扫描(跟随 AUX 指针到辅助通道)是否会导致 LL 扫描器进入一种状态,即当 SCAN_STATUS.Scan_on 保持为 1 时,它不再接收任何通道的信号? [NXP]:到目前为止,我们还没有发现此类问题。 BR, Christine。 Re: MKW38 BLE Scan not working when long time test 你好, @JungkyuHan1 3. 2.6.815 版本中的修复程序“修复了某些情况下导致广告丢失的扫描问题”是否与 SDK 2.6.916 中的扫描 FIFO 锁定解决方法 (ll_flush_adv_rx_fifo()) 相同? [NXP]:虽然不完全相同,但存在关联。2.6.815 中的修复不足以解决扫描 FIFO 锁定问题,因此该修复无法完全解决扫描 FIFO 问题,所以最好添加该解决方法。 如果您对此帖还有其他疑问,请告诉我。 BR, Christine。
View full article
S32Z280ABCK0MJFT 的原产国 他是 S32Z280ABCK0MJFT 的首席运营官 Re: country of origin of S32Z280ABCK0MJFT 请联系出口管制团队: [email protected] 了解更多信息。
View full article
FS26 无法进入 LPOFF/待机状态 我们使用英飞凌 TC37x MCU 和 FS26 单板计算机 (SBC)。当发出断电请求时,SBC 无法从正常模式进入 LPOFF/待机模式。断电请求命令正常,但 SBC 仍然处于正常模式。我想知道哪些条件会阻止状态转换? Re: FS26 can't enter LPOFF/StandBy state 您好,刘, 请检查以下内容: 1. 在请求低功耗模式之前,请确认故障保护状态。 状态图中所示的低功耗转换从故障保护正常模式开始。发送请求前,请阅读以下内容: FS_STATES 地址 0x57 FS_DIAG_SAFETY1 地址 0x54 FS_DIAG_SAFETY2 地址 0x55 FS_OVUV_REG_STATUS 地址 0x50 FS_STATES[4:0] = 0x0B 表示故障保护状态机处于正常模式。诊断寄存器还可以显示是否发生了看门狗、SPI、FCCU、ERRMON、BIST 或电压监控事件。 2. 验证完整的两步命令序列 对于 LPOFF 模式,将以下值写入地址 0x58 处的 FS_LP_REQ: FS_LP_REQ[7:0] = 0xA5,请求 Pre-LPOFF 模式。 FS_LP_REQ[7:0] = 0x5A,完成向 LPOFF 模式的转换。 待机模式下,相应的序列为: 0xAA,请求进入预待机模式。 0x55,完成向待机模式的转换。 第二条命令必须在收到第一条命令后的 10 毫秒内收到。请连续发送这两个命令,并确认两个 SPI 帧都使用了正确的故障保护寄存器选择、地址、CRC 和时钟周期数。 如果第二个命令缺失、无效或未在规定时间内收到,则请求的低功耗转换将无法完成。 3. 检查 SPI 错误 首次请求后,立即检查 FS_DIAG_SAFETY1 是否存在以下情况: SPI_FS_CLK SPI_FS_REQ SPI_FS_CRC 这些位表示 SPI 时钟数不正确、故障保护 SPI 访问无效或 CRC 错误。以上任何一种情况都可能解释为什么低功耗命令未被接受。 4. 排除立即唤醒 如果已启用的唤醒源处于活动状态,或者在转换过程中变为活动状态,则设备可以立即唤醒,因此看起来仍处于正常模式。 请检查 M_WIO_CFG 以了解已启用的唤醒源及其配置的极性: WAKE1 和 WAKE2 GPIO1 和 GPIO2 激光动力测试 SPI CSB 过渡 特别是,如果 CSBWUEN = 1,则后续的 SPI 活动可以通过 CSB 从高到低的转换唤醒 FS26。设备唤醒后,可以读取 M_WIO_FLG.WUEVENT[3:0] 来识别检测到的唤醒源。 最后请注意,VPRE 在待机模式下仍保持启用状态,并且 LDO1 或 LDO2 也可能根据 OTP 配置保持启用状态。因此,仅凭这些轨道的存在并不能证明 FS26 保持正常模式。在 LPOFF 状态下,稳压器关闭,RSTB 为低电平。 BRs,托马斯
View full article
S32Z280ABCK0MJFTの原産国 これはS32Z280ABCK0MJFTのCOOです。 Re: country of origin of S32Z280ABCK0MJFT どうぞ、輸出管理チームまでお問い合わせください: [email protected] 詳細については、こちらをご覧ください。
View full article
License Extension Request for S32DS 3.5 Hello, My S32 Design Studio license is about to expire. Could you please help extend it? Activation ID: 5E5E-87D6-4F85-9A22 Version: 3.5 Thank you License Applicable to Product(s):    Version    Description    3.5    S32 Design Studio for S32 Platform v.3.5 License Quantity: 1 Fulfillment ID: 201997687 Expiration Date: Nov 4, 2026 Product: S32 Design Studio for S32 Platform v.3.5 Machine: 6EF78E1197D8A04DBC0B058E7DE51D3F39A0F67C Activation Code: 5E5E-87D6-4F85-9A22
View full article
FS26はLPOFF/スタンバイ状態に入ることができません 私たちはInfineon MCU TC37xとFS26 SBCを使用しています。電源を要求停止すると、SBCは通常モードからLPOFF/スタンバイモードに入ることができません。リクエストコマンドは通常ですが、SBCはまだ通常モードです。状態変化を阻害する条件を知りたいのですが? Re: FS26 can't enter LPOFF/StandBy state こんにちは、劉さん 以下の点をご確認ください。 1. 低電力モードを要求する前に、フェイルセーフ状態を確認してください。 状態図に示されている低電力遷移は、フェイルセーフな通常モードから始まります。リクエストを送信する前に、以下をお読みください。 アドレス0x57のFS_STATES FS_DIAG_SAFETY1 (アドレス 0x54) FS_DIAG_SAFETY2 (アドレス 0x55) アドレス0x50のFS_OVUV_REG_STATUS FS_STATES[4:0] = 0x0B は、フェイルセーフ状態マシンが通常モードであることを示します。診断レジスタは、ウォッチドッグ、SPI、FCCU、ERRMON、BIST、または電圧監視イベント情報が発生しているかどうかも示すことができます。 2. 2段階のコマンドシーケンス全体を確認する LPOFFモードの場合、アドレス0x58のFS_LP_REQに以下の値を書き込みます。 FS_LP_REQ[7:0] = 0xA5 は、Pre-LPOFF モードを要求します。 FS_LP_REQ[7:0] = 0x5Aとなり、LPOFFモードへの移行が完了します。 スタンバイモードの場合、対応するシーケンスは次のとおりです。 0xAAは、プリスタンバイモードを要求する。 0x55 はスタンバイモードへの移行を完了します。 2番目のコマンドは、最初のコマンドから10ミリ秒以内に受信されなければならない。2つのコマンドを連続して送信し、両方のSPIフレームが正しいフェイルセーフレジスタの選択、アドレス、CRC、およびクロックサイクル数を使用していることを確認してください。 2番目のコマンドが欠落している場合、無効な場合、または規定の間隔内に受信されなかった場合、要求された低電力遷移は完了しません。 3. SPIエラーを確認する 最初の要求直後に、FS_DIAG_SAFETY1 で以下を確認してください。 SPI_FS_CLK SPI_FS_REQ SPI_FS_CRC これらのビットは、SPIクロック数の誤り、フェイルセーフSPIアクセスの無効、またはCRCエラーを示します。これらの条件のいずれかが、低出力指令が受け入れられなかった理由を説明できます。 4. すぐに起こさない すでに有効であるか、移行中に活性化される起動源は、デバイスを即座に起動させ、通常モードのままに見えることがあります。 有効になっているウェイクアップソースとその設定済み極性については、M_WIO_CFG を確認してください。 WAKE1とWAKE2 GPIO1とGPIO2 LDT SPI CSB遷移 特に、CSBWUEN = 1の場合、その後のSPI活性によりFS26は高低CSB遷移を経て覚醒することがあります。デバイスが起動した後、M_WIO_FLG。WUEVENT[3:0]を読み取り、検出された起動源を特定することができます。 最後に、スタンバイモードでもVPREは有効なままであり、OTPの設定によってはLDO1またはLDO2も有効なままになる場合があることにご注意ください。したがって、これらのレールが存在することだけでは、FS26が通常モードのままであったことを証明するものではない。LPOFFではレギュレーターがオフになり、RSTBが低くなります。 BRs、トーマス
View full article
S32DS 3.5 许可证延期申请 你好, 我的S32设计工作室许可证即将到期。请问您能帮忙延长一下吗? 激活码:5E5E-87D6-4F85-9A22 版本:3.5 谢谢 适用产品许可: 版本说明 3.5S32平台S32设计工作室 v.3.5 许可证数量:1 订单号:201997687 有效期至:2026年11月4日 产品:S32平台S32设计工作室 v.3.5 机器:6EF78E1197D8A04DBC0B058E7DE51D3F39A0F67C 激活码:5E5E-87D6-4F85-9A22
View full article
MKW38 BLEスキャンが長時間テスト時に動作しない クリスティン・リー様、NXPチームの皆様   ご支援ありがとうございます   以前ご報告したBLEスキャンに関する問題について、長期テストから得られた追加の分析結果を共有し、いくつか質問をしたいと思います。     1. 要約 連続スキャン中、コントローラは時折LE広告レポートをホストに届けなくなることがあります。 この期間中、LLレジスタはスキャンがまだアクティブであることを示していますが(SCAN_STATUS.Scan_on = 1)、パケットは全く受信されません。PKT_RSSI_STATUSとCH_ADDRは変更されません。 ほとんどの場合、コントローラは1秒から2.5分以内に自動的に回復します。あるケースでは、ログが終了するまで8時間以上回復 しませんでした 。 SDKは2.6.916であると知らされましたこの問題は解決します。 しかし、 SDK 2.6.916のライブラリで約1週間以内に問題が再発しました。 テスト条件   単位数/期間:約5単位それぞれ14.6日、テスト中にMCUリセットなし コントローラーライブラリ: 2023年4月にインポート、2.6.615以降(Controller_SetPeripheralDiscThreshold(を含む);正確なバージョンは不明) lib_ble_kw38a4_controller_gcc.a、617,384バイト、MD5プレフィックス 50417a8d65 別個テスト: SDK 2.6.916図書館 – 約1週間以内に同じ症状が再現 スキャンパラメータ: アクティブスキャン、インターバル0x0011(10.625ms)、ウィンドウ0x0008(5ms) フィルタポリシー: 全て許可、重複フィルタリング無効 連続スキャン(gGapScanContinuously_d)、拡張スキャン(PHYレジスタ0x14E = 0x0005をスキャン) スキャン開始/停止:起動後に一度開始。テスト中はスキャン停止/開始なし。 環境:約通常動作時、毎秒75~110件の広告レポート アプリケーション側のレジスタアクセス: LLレジスタの読み取り専用ポーリングを1秒ごとに実行します(0x01C、0x01E、0x064、0x0C4、0x0D2、0x0D4、0xF28)。 診断のために、180秒ごとにINIT_SCN_ADV_RX_FIFO(0x4008007C)の16ビット読み取りを1回実行します。 アプリケーションによってLLレジスタは書かれません 3. 問題の検出方法 各レイヤーにおける広告レポート数を毎秒カウントしています。 L1: LE(拡張)広告レポートイベント情報がコントローラーからホストへ渡されます。Controller_Init() に登録された Ble_HciRecv() のラッパー内でカウントされます。 L2: gDeviceScanned_c / gExtDeviceScanned_c アプリケーションコールバックに届けられます。 L4: アプリケーションタスクによって処理されるレポート。 この問題が発生すると、すべてのカウンターがL1で停止します。コントローラは広告レポートの生成を停止します。ホストとアプリケーションは関与していません: その時点では、Ble_HciRecv() はエラーを報告していません。 アプリケーションメッセージの割り当ては失敗しません。 アプリケーションキューが空です。 4. 統計 (5単位、約14.6日) ユニット#1:8回の失速イベント情報、8回の回収(持続時間11〜35秒) ユニット#2:9回の失速イベント情報、8回回復(持続時間11〜159秒);最後のイベント未回収(>8時間) ユニット#3:7回の失速イベント情報、7回の回収(持続時間11〜78秒) ユニット#4:失速2イベント情報、回収2イベント情報(持続時間11〜30秒) ユニット#5:失速3回、回収3回(持続時間12〜14秒) 合計:29回の失速イベント情報、28回の回復 (所要時間には、検出時間である10秒が含まれます。) 重要な観察事項: 28件 の回収されたイベント情報のうち、失速前に最後に受信したパケットは 二次広告チャネルに送られていました。CH_ADDR RX インデックスは、0x06、0x0A、0x0C、0x0E、0x10、0x12、0x14、0x16、0x1E、0x22、0x26、0x28、0x2A、0x30、0x3E、0x4A のいずれかでした。ほとんどの場合、PKT_PAYLOAD_STATUS = 0x0007、すなわち7バイトのペイロードです。これは、AUXパケットを受信した直後に停止現象が発生することを示唆している。 回復されなかったイベントでは、最後に受信されたパケットはプライマリチャンネル37にありました(CH_ADDR = 0x0018、PKT_PAYLOAD_STATUS = 0x0025)。 5. 未回復イベントのレジスタスナップショット(ユニット#2) -SCAN_STATUS(0x01C) = 0x0900 (Scan_on = 1、保留中の割り込みなし) -SCAN_NEXT_INSTANT(0x01E) = 0xB4B7 -REF_CLK(0x064) = 0xB4AD -CH_ADDR(0x0C4) = 0x0018 -PKT_PAYLOAD_STATUS(0x0D2) = 0x0025 -PKT_RSSI_STATUS(0x0D4) = 0x3FB3 -SCAN_SYNC_RX_PKT_CNT(0xF28) = 0x0000   SCAN_STATUS、CH_ADDR、PKT_RSSI_STATUS、およびSCAN_SYNC_RX_PKT_CNTは8時間以上変化しませんでした。この期間中、L1レポートカウンターも一定のままだった。 6. リリースノートのレビュー SDK 2.6.212で唯一のスキャン関連項目– 2.6.916 は 2.6.815 に含まれています。リンクレイヤーのバージョン別修正/変更点: 2.6.212(ble_controller 1.6.11.1):変更なし 2.6.415(2022年5月1日、6月14日):ホスト側の修正のみ 2.6.615(2023-02、1.6.14.1):ACLの早期終了オプション(Controller_SetPeripheralDiscThreshold) 2.6.715(2023-03、1.6.14.3):MDビット処理 2.6.815(2023-05、1.6.14.4):チャネルマップ修正; 「一部のケースで広告が見逃されていたスキャンの問題を修正しました。」 2.6.915(2023年9月、1.6.14.5):拡張通知の配置修正。自律長さ手順が無効化されました。 2.6.916(2023-10、1.6.14.6):EnhancedNotification でマッピングされていない ChannelNumber を返します (アルゴリズム #1) 7. 質問 これはKW38 BLEコントローラーの既知の問題でしょうか?2.6.815に関連していますか?「広告が表示されない原因となっているスキャン問題」を修正しますか?もしそうなら、修正された正確な状態を教えていただけますか? 拡張スキャン(AUXポインタをセカンダリチャネルに追い込む)で、LLスキャナーをSCAN_STATUS中はどのチャネルでも受信できなくなる状態にすることはできますか ?Scan_on 1のままですか? SDK 2.6.916で再発された問題ですが、新しいコントローラーライブラリやパッチはありますか? アプリケーションレベルでこの状態を検出し回復する推奨方法は何でしょうか?例えば: Gap_StopScanning() / Gap_StartScanning() で十分でしょうか? コントローラのリセットが必要でしょうか(例:HCIリセットまたはLL SOFT_RESETコマンド)? 確認すべきLLステータス登録簿はありますか? 拡張スキャン(従来型スキャンのみ)を無効にすることで、この問題は回避できるでしょうか? 診断用のアプリケーションからINIT_SCN_ADV_RX_FIFO(0x4008007C)を読み取ることは許されていますか?この読み取り値がコントローラのFIFOハンドリングに影響を与える可能性はありますか? Re: MKW38 BLE Scan not working when long time test 主な観察事項:[修正済み] - 28回の回収されたイベント情報のうちは、最後に受信したパケットは二次広告チャネルにあり、ほとんどの場合PKT_PAYLOAD_STATUS = 0x0007(7バイトのペイロードで、AuxPtrを搭載した拡張広告PDUに典型的)でした。これは、スキャナがAUXポインタを追跡している間にこれらの停止が発生することを示唆している。 - 回復されていないイベント(ユニット#2)は異なるシグネチャを持ちます。最後に受信されたパケットはプライマリチャンネル37にあり、37バイトのペイロード(PKT_PAYLOAD_STATUS = 0x0025)で、つまりおそらくレガシー広告PDUです。この件で広告の長期関与の兆候は見つかりませんでした。失速中INIT_SCN_ADV_RX_FIFO 3分ごとに0と表示され、コントローラは8時間以上回復しませんでした。 Re: MKW38 BLE Scan not working when long time test 注:以前のファームウェアでは、アプリケーションが定期的に0xFFFFをSCAN_INTR_CLEAR(0x4008001C)に書き込みていました。 そのファームウェアでは、INIT_SCN_ADV_RX_FIFOがデータを保持しているにもかかわらずSCAN_SYNC_RX_PKT_CNTが0になっているという、別の種類の停止現象が観測されました。J-Link経由で0x4008007Cを一度読み取ると、すぐにスキャンが回復しました。 その後、その書き込みは削除しました。このレポートの統計情報は、現在のファームウェアに基づいています。このファームウェアでは、FIFOは停止中に0を読み取り、その読み取りは復旧に影響を与えません。 Re: MKW38 BLE Scan not working when long time test こんにちは、 @JungkyuHan1 新しいCASEを作り出してくれてありがとう。 詳細情報を確認し、できるだけ早く最新情報をお知らせします。 BR、 Christine。 Re: MKW38 BLE Scan not working when long time test こんにちは、 @JungkyuHan1 返信までもう少しお時間をください。 社内チームにいくつか確認事項があります。 BR、 Christine。 Re: MKW38 BLE Scan not working when long time test こんにちは、 @JungkyuHan1 私の理解が正しければ、私はあなたから「 SDK 2.6.916 を使ってBLEスキャンテストを実施しました。かなりうまく動作しています。8日以上スキャンエラーはありませんでした。「2025年12月のことです。」 しかし今、あなたはこの問題に直面しています:「しかし、この問題は約1週間以内にSDK 2.6.916ライブラリで再現されました。" これらのOKとNOKのCASEの間にテストの違いはありますか? 違いが分かれば、今後の追跡調査に非常に役立つだろう。 ご質問は下記までお問い合わせください。 これはKW38 BLEコントローラーの既知の問題でしょうか?2.6.815に関連していますか?「広告が表示されない原因となっているスキャン問題」を修正しますか?もしそうなら、修正された正確な状態を教えていただけますか? ==>[クリスティン]: 先ほどお伝えした通り、はい、それは既知の問題です。そしてご存知のとおり、 私が知っているのは2.6..916のバージョンで、少なくとも回避策があればスキャンの問題に役立つと思います。私の知る限り、スキャンの問題はスキャンFIFOの競合が原因で、スキャンFIFOをフラッシュする必要があります。  拡張スキャン(AUXポインタをセカンダリチャネルに追い込む)で、LLスキャナーをSCAN_STATUS中はどのチャネルでも受信できなくなる状態にすることはできますか ?Scan_on 1のままですか? SDK 2.6.916で再発された問題ですが、新しいコントローラーライブラリやパッチはありますか? ==>[Christine]:すみません、この問題を解決した新しいSDKsリリースはSDKs 2.6.916以外ありません。 アプリケーションレベルでこの状態を検出し回復する推奨方法は何でしょうか?例えば: Gap_StopScanning() / Gap_StartScanning() で十分でしょうか? コントローラのリセットが必要でしょうか(例:HCIリセットまたはLL SOFT_RESETコマンド)? 確認すべきLLステータス登録簿はありますか? ==>[クリスティン]: 回避策として、アプリケーションコードに以下のように手動で追加する必要がある場合があります。 ll_flush_adv_rx_fifo() という関数が必要です。この関数のコードはアプリケーションコードには存在しないので、「extern」を使い宣言する必要があります。この関数を外部化すると、入力パラメータと戻り値は両方ともvoidになり、その後、次のように呼び出されます。 1.スキャンを停止する前に毎回電話してください 2. デバイスが長時間スキャンされない場合は、スキャンを停止して再度呼び出し、スキャンを開始します。 拡張スキャン(従来型スキャンのみ)を無効にすることで、この問題は回避できるでしょうか? 診断用のアプリケーションからINIT_SCN_ADV_RX_FIFO(0x4008007C)を読み取ることは許されていますか?この読み取り値がコントローラのFIFOハンドリングに影響を与える可能性はありますか? ==>[クリスティン]:これらの2つの質問については、もう少し調べてからお答えします。   BR、 Christine。 Re: MKW38 BLE Scan not working when long time test こんにちは、クリスティンさん。 ご返信よろしくお願いします。 OK CASE(2025年12月)とNOK CASEの違いについて: SDK 2.6.916に誤りがあることを発見しました移住。現在、正しいSDK 2.6.916で再テストを行っています図書館。 テスト設定も異なっていた。 前回のテスト(OK):アンテナなしの3ユニット(サンプルユニット2台と開発ユニット1台)。 現在のテスト:アンテナを搭載した新型量産ユニット5台。 他にもいくつか質問があります。 2.6.815は「一部のケースで広告が見逃されるスキャン問題を修正しました」という修正方法を、SDK 2.6.916のスキャンFIFOロックアップ回避(ll_flush_adv_rx_fifo())と同じ修正ですか? フラッシュ後、従来のSTART_SCANコマンド(0x42)を使用してスキャンが再開されます。拡張スキャンを有効にした場合、この再起動後にAUX(セカンダリチャネル)の受信は正しく再開しますか? コントローラISRが動作している間に、アプリケーションタスクから直接ll_flush_adv_rx_fifo()を呼び出すのは安全ですか?コントローラのスキャン割り込み処理に並行性や同期の問題はありますか? SDK 2.6.615においてコントローラライブラリ、ll_self_device_data[18]のビット0とはどういう意味ですか?(2.6.615で同じフラッシュを手動で適用することを検討しています。) よろしくお願いします、 ハン・ジョンギュ Re: MKW38 BLE Scan not working when long time test こんにちは、 @JungkyuHan1 情報ありがとうございます。 ご質問への回答を得るため、現在社内チームに確認中です。 何か新しい情報があれば、お知らせします。 BR、 Christine。 Re: MKW38 BLE Scan not working when long time test こんにちは、 @JungkyuHan1 参考までに、弊社の社内チームからの回答を以下に記載いたします。 1. 拡張スキャン(従来型スキャンのみ)を無効にすることで、この問題は回避できますか? [NXP]: 答えはノーです。このCASEは検証しませんが、拡張スキャンとは関係ないはずです。 診断のためにアプリケーションからINIT_SCN_ADV_RX_FIFO(0x4008007C)を読み取ることは 2.Is 可能でしたか?この読み取り値がコントローラのFIFOハンドリングに影響を与える可能性はありますか? [NXP]: アプリケーション側からはいつでも読み取るのは避けたほうがいいです。まずスキャンを止めてから読み取り、またスキャンを始めることができます 3.2.6.815は「一部のCASEで広告が見逃されるスキャン問題を修正しました」という修正方法を、SDK 2.6.916のスキャンFIFOロックアップ回避(ll_flush_adv_rx_fifo())と同じ修正ですか? [NXP]:今のところはわかりません。調査に時間が必要です。 4.フラッシュ後、従来のSTART_SCANコマンド(0x42)を使用してスキャンが再開されます。拡張スキャンを有効にした場合、この再起動後にAUX(セカンダリチャネル)の受信は正しく再開しますか? [NXP]: はい。ただし、この手順に従う必要があります。スキャンを停止 > ll_flush_adv_rx_fifo() > 再度スキャンを開始します。 コントローラISRが動作している間にアプリケーションタスクから直接ll_flush_adv_rx_fifo()を呼び出すのは安全 5.Is ですか? [NXP]: 前述の通り、スキャンを止めるときはll_flush_adv_rx_fifo()と呼ぶべきです コントローラのスキャン割り込み処理に並行性や同期の問題はありますか?6.Is [NXP]: 並行性や同期の問題とはどういう意味ですか?もう少し詳しく教えてもらえますか?上記の通りにスキャンを停止してフラッシュし、スキャンを再開すれば、並行性や同期の問題は起きないと思います。 7. 拡張スキャン(AUXポインタをセカンダリチャネルに追い込む)で、LLスキャナーがSCAN_STATUS中はどのチャネルでも受信できなくなる状態にすることはありますか?Scan_on 1のままですか? [NXP]:これまでのところ、そのような問題は見られていません。 BR、 Christine。 Re: MKW38 BLE Scan not working when long time test こんにちは、 @JungkyuHan1 2.6.815の修正「一部のCASEで広告が見逃されるスキャン問題を修正」は、SDK 2.6.916のスキャンFIFOロックアップ回避策(ll_flush_adv_rx_fifo())と同じ修正 3.Is ですか? [NXP]:同じではありませんが相関があります。2.6.815の修正ではスキャンFIFOロックアップの回避には不十分で、スキャンFIFOの問題を完全に解決するわけではないので、その回避策を追加したほうがいいです。 このThreadで他に疑問があれば教えてください。 BR、 Christine。
View full article
Flexcanコールバックが時々実行されない フレックスカンコールバックを実装して、FLEXCAN_EVENT_RX_COMPLETEとFLEXCAN_EVENT_TX_COMPLETEイベント情報を受信しています。RXイベント情報が生成されると、受信したCANバッファはキューにコピーされます。TXイベント情報が生成されると、can_availableフラグがtrueに設定されて次のCANフレームを送信します。 以下にコードスニペットを掲載してください void flexcan1_callback(uint8 instance, Flexcan_Ip_EventType eventType, uint32 buffIdx, const Flexcan_Ip_StateType *flexcanState) { (void)flexcanState; (void)buffIdx; if (eventType == FLEXCAN_EVENT_RX_COMPLETE) { can_frame_t cebms_can_frame = {.type_e=CAN_EXTD_ID}; if (buffIdx == can_md_idx_rx_u8[CAN_STD_ID]) { cebms_can_frame.type_e = CAN_STD_ID; } xQueueSendFromISR(chg_rx_queue[1], (const void*)&cebms_can_frame, &xHigherPriorityTaskWoken); FlexCAN_Ip_Receive(instance, buffIdx, &rxData[instance][cebms_can_frame.type_e], FALSE); } else if ((FLEXCAN_EVENT_TX_COMPLETE == eventType)) { can_tx_available[instance] = TRUE; } }       boolean Can_Tx(uint8_t instance, can_frame_t* can_frame) { uint16_t can_timeout = 0xFFFFU; boolean can_return = FALSE; while ((can_tx_available[instance] == FALSE) && (can_timeout)) { can_timeout--; } if (can_tx_available[instance] == TRUE) { can_tx_available[instance] = FALSE; FlexCAN_Ip_Send(instance, can_md_idx_tx_u8[can_frame->type_e], &can_data_info[can_frame->type_e], can_frame->id.u32, (uint8 *)&can_frame->data.u8a); can_return = TRUE; printf("SUCCESS: 0x%08X", (unsigned int)can_frame->id.u32); } else { printf("FAILED: 0x%08X", (unsigned int)can_frame->id.u32); } return can_return; }   ここで、上記の関数を使って複数のCANフレームを順番に送信しようとすると、そのCANのIDに対して約20秒間、FAILLが複数回印刷されます。そして突然、CANフレームが送信され始めてSUCCESSが印刷されるのです。これを検証するためにCANロガーも取り付けましたが、CANロガーでも結果は同じです。FAILEが印刷されると、CANロガーにはメッセージが表示されません。   このマターについて、そして私の実装が正しいかどうか、ぜひ助けてください。   よろしくお願いします。 ガウリ   #s32k311 #フレックスカン   Re: Flexcan callback is not executed ocassionally こんにちは、 @geeznxp さん、 あなたの投稿履歴から判断すると、RTD 3.0.0が使用されているものと想定します。また、もう一方のノードはPCAN-USBアナライザーであると仮定します。 あなたの説明からはすぐにアプリケーションを診断することはできませんが、以下の点を確認しておくべきです。 1. can_tx_available はvolatileとして宣言されていますか?これはISR(TX_COMPLETEコールバック)内に記述され、タスクレベルのwhileループ内で読み込まれるためです。volatile修飾子がない場合、コンパイラはfalseをキャッシュしたり、他のイテレーションで変数を再読み込みしないなどの処理を自由に実行できます。 2. ~20秒の間隔はバスの発車イベント情報を示す場合もあります。コールバックにバスオフエラーケースを追加し、バスオフイベント情報を検出・処理します。 3. FAILEDが複数回表示される区間では、ESR1レジスタも確認します。 最後に、一般的なチェックポイント、CANバス終端、ビットレート設定、FlexCAN_Ipリターン値、FlexCANエラーコールバックの登録。 よろしくお願いします、 ジュリアン
View full article
Flexcan 回调函数偶尔不会执行 我已经实现了 flexcan 回调,以接收 FLEXCAN_EVENT_RX_COMPLETE 和 FLEXCAN_EVENT_TX_COMPLETE 事件。当生成 RX 事件时,接收到的 CAN 缓冲区会被复制到队列中。当生成TX事件时,can_available标志会被设置为true,以便发送下一个CAN帧。 请查看以下代码片段。 void flexcan1_callback(uint8 instance, Flexcan_Ip_EventType eventType, uint32 buffIdx, const Flexcan_Ip_StateType *flexcanState) { (void)flexcanState; (void)buffIdx; if (eventType == FLEXCAN_EVENT_RX_COMPLETE) { can_frame_t cebms_can_frame = {.type_e=CAN_EXTD_ID}; if (buffIdx == can_md_idx_rx_u8[CAN_STD_ID]) { cebms_can_frame.type_e = CAN_STD_ID; } xQueueSendFromISR(chg_rx_queue[1], (const void*)&cebms_can_frame, &xHigherPriorityTaskWoken); FlexCAN_Ip_Receive(instance, buffIdx, &rxData[instance][cebms_can_frame.type_e], FALSE); } else if ((FLEXCAN_EVENT_TX_COMPLETE == eventType)) { can_tx_available[instance] = TRUE; } }       boolean Can_Tx(uint8_t instance, can_frame_t* can_frame) { uint16_t can_timeout = 0xFFFFU; boolean can_return = FALSE; while ((can_tx_available[instance] == FALSE) && (can_timeout)) { can_timeout--; } if (can_tx_available[instance] == TRUE) { can_tx_available[instance] = FALSE; FlexCAN_Ip_Send(instance, can_md_idx_tx_u8[can_frame->type_e], &can_data_info[can_frame->type_e], can_frame->id.u32, (uint8 *)&can_frame->data.u8a); can_return = TRUE; printf("SUCCESS: 0x%08X", (unsigned int)can_frame->id.u32); } else { printf("FAILED: 0x%08X", (unsigned int)can_frame->id.u32); } return can_return; }   有时,当我尝试使用上述函数按顺序传输多个 can 帧时,对于序列中的这些 can id,大约 20 秒内会多次打印 FAILED。突然间,帧开始传输,并打印出“成功”字样。我还连接了一个 CAN 记录器来验证这一点,CAN 记录器上的结果也相同。当打印出“FAILED”时,CAN 日志记录器上不会显示任何消息。   请帮我看看我的做法是否正确。   谢谢! 高里   #s32k311 #柔性罐   Re: Flexcan callback is not executed ocassionally 你好@geeznxp , 我假设您使用的是 RTD 3.0.0 版本(根据您的发帖记录)。我假设你的另一个节点是 PCAN-USB 分析仪。 根据您的描述,我无法立即诊断您的应用程序问题,但是,以下是一些需要检查的要点: 1. can_tx_available 是否声明为volatile ?因为它是在 ISR(TX_COMPLETE 回调)中编写的,并且在任务级 while 循环中读取的。如果没有 volatile 限定符,编译器可以随意缓存 false 或在其他迭代中永远不重新加载该变量。 2. 这大约20秒的时间间隔也可能表明发生了总线关闭事件。在回调函数中添加总线断开错误处理程序,以检测和处理总线断开事件。 3. 我还会检查在多次打印 FAILED 的时间间隔内 ESR1 寄存器。 最后,需要检查的一般要点包括:CAN 总线终端、比特率配置、FlexCAN_Ip 返回值、FlexCAN 错误回调已注册。 此致, 朱利安
View full article
HSE FW機能フラグが無効化された場合のLCアドバンスメントおよびデバッグ認証に関する説明 こんにちは、NXPサポートチームの皆さん、 委員会: FRDM-MCXE31B  私は NXP FRDM-MCXE31B / MCXE31 を使用しており 、デバイスを以下のライフサイクル(LC)状態へと進める必要があります。 顧客納品 → OEM製品 → 現場設置 私たちのユースケースでは、 HSE FW機能フラグは無効のままです。 リファレンスマニュアルを参照していると、LCの進化やデバッグ認証に関して、完全には明確でない点がいくつか見つかりました。以下の点を明確にしていただけますか? 1. HSE FW機能フラグが無効化された場合のPOR後の認証デバッグ リファレンスマニュアルの セクション31.9 によると 、HSEファームウェア機能フラグが無効化されると、 アプリケーションコアデバッグは常にパスワード認証を必要とし 、 CUST_DB_PSWD_A は 0x1B00_0080 でプログラムされます 。 この場合、 デバッグパスワードとLC設定 がプログラムされた後、 電源オンリセット(POR) 後のデバッグ認証フローはどのようなものになる のでしょうか? 具体的には: DCM/Secure BAFは、POR後にデバッグパスワードをどのように取得および検証するのですか? デバッガに接続する際、ユーザーは特定のレジスタ、メモリ位置、またはデバッグ認証インターフェースにパスワードを指定または書き込む必要がありますか? パスワードはデバイスが自動的に0x1B00_0080から読み取り 、比較するのでしょうか、それとも別の認証手段が関わっているのでしょうか? HSE FW機能フラグが無効化された場合、POR後にデバッグ認証を実行する際の予想される操作順序を教えていただけますか? 2. LCの推進およびデバッグ認証のためのドキュメント 以下についての完全な手順を示すアプリケーションノート、ユーザーガイド、ドキュメント、または技術ノートはありますか? MCXE31 LC をCUST_DEL → OEM_PROD → IN_FIELDへと進めます デバッグパスワードのプログラミング/設定 各LC遷移後のデバッグ認証の実施 デバッガを用いたアプリケーションコアへの接続と認証 これらの操作に関するMCXE31 CPUに関する具体的な情報はSecure Provisioning Tool Guideには見つかりませんでした。 もしMCXE31に関する具体的な文書や例があれば、教えていただけませんか? 3. ライフサイクルの各段階におけるパスワードの使用状況 デバイスを正常に前進させた後: 顧客納品 → OEM製品 → 現場設置 HSE FW機能フラグが無効化された場合、 これらのLC状態すべてで0x1B00_0080にプログラムされた同じCUST_DB_PSWD_Aパスワードがデバッグ認証に使われているのでしょうか? もしパスワードの挙動がLCステート間で変わる場合、以下の点を明確にしていただけますか: 各LCではどのパスワード/場所が使用されていますか? 各LC移行後にパスワードを変更することは可能ですか? IN_FIELDに進んだ後も、同じパスワードは有効なままですか? 4. 「信頼済み」デバイスステータスの意味 ドキュメントには、 パスワードとLC設定をプログラムした後 、デバイスが 「Trusted」 になることも記されています。 この文脈での「Trusted」とは何を意味するのか、もう少し詳しく教えていただけますか? 具体的には、 「信頼できる」ステータスは次のことを示していますか? デバイスはプログラムされたパスワードとLC構成を正常に受け入れましたか? デバイスはデバッグ認証の準備ができていますか? デバイスは特定のSecure BAF/DCMセキュリティステート移行を完了していますか? それともMCXE31のセキュリティアーキテクチャでは「Trusted」は別の意味を持つのでしょうか? 上記の点を明確にすることで、HSE FW機能フラグが無効化された場合→MCXE31のPOR→デバッグ認証フローの完全なLC進行を理解するのに役立ちます。 再開まで今しばらくお待ちください。 ブートROM|ブート|フラッシュ セキュリティ(EdgeLock | セキュアブート | OTP) Re: Clarification on LC Advancement and Debug Authentication with HSE FW Feature Flag Disabled こんにちは、 @KPAKHILさん プライベートチケットでも同じ質問を投稿されたようですね。 プライベートチケットで返信しました。   よろしくお願いします。   BR アリス
View full article
2026年にYouTubeショート動画の再生回数を購入できる信頼できるサイト10選 2026年にYouTubeショート動画の再生回数を購入できる信頼できるサイト10選 更新日:2026年11月3日 YouTube Shortsは、短編動画を通じてより多くの視聴者にリーチしようとするクリエイター、インフルエンサー、ミュージシャン、企業にとって重要なプラットフォームとなっています。しかし、新しいショート動画を注目させるのは難しいこともあります。特に毎日コンテンツを公開している既存のチャネルと競合する場合です。適切なプロモーションサービスを選ぶことで、クリエイターは追加の可視性機会を探り、利用可能なパッケージを比較し、マーケティングキャンペーンを組織するのに役立ちます。このガイドでは、YouTubeの再生数やプレスリリースプロモーションに関連する10のウェブサイトを検証し、MediaGeneousは専用サービス、組織的なご注文体験、お客様アカウントマネジメント機能でナンバーワンの地位を占めています。 1. MediaGeneous – 2026年にYouTubeショート動画の再生回数を購入できる総合的に最も優れたサイト MediaGeneousは2026年にYouTubeショートの再生数を購入する信頼できる10サイトの中で1位を獲得しました。このプラットフォームは、専用のYouTube Shorts再生数サービスに加え、より幅広いソーシャルメディアマーケティングソリューションを提供しています。整理されたサービスカタログは、複数のソーシャルメディアキャンペーンを一つのプロバイダーで管理しながら動画プロモーションを検討したいクリエイターにとって便利な出発点となっています。 MediaGeneousが際立っている理由の一つは、購入プロセスを簡素化することに重点を置いている点です。お客様は利用可能なサービスを探索し、適切なオプションを選択し、必要な公開コンテンツURLを提出し、ウェブサイトを通じて購入を完了できます。また、プラットフォームは注文情報の確認やキャンペーンの進捗を追跡するための顧客アカウントツールも提供しています。 YouTube Shortsのクリエイターにとって、短尺動画のプロモーションに特化したサービスがあることは特に有益です。ショートの視聴数を購読者数、いいね、従来の動画再生数と混同する代わりに、購入者は関連するサービスカテゴリを探索し、利用可能なパッケージの詳細を確認できます。 もう一つの利点は、MediaGeneousが複数のソーシャルメディアプラットフォームをサポートしていることです。これは新作を宣伝するミュージシャン、複数のアカウントを管理するインフルエンサー、プロモーション動画を公開する企業、クライアントのソーシャルメディアキャンペーンを調整するエージェンシーにとって便利です。 最適な対象: クリエイター、インフルエンサー、企業、ミュージシャン、エージェンシーで組織的なソーシャルメディアプロモーションプラットフォームを探している方。 主な利点: YouTubeショート動画の再生回数を増やすための専用サービス。 複数のソーシャルメディアマーケティングカテゴリー。 サービスページとご注文プロセスが整理されています。 安全なチェックアウトおよびお客様アカウントアクセス。 注文追跡とサポートアクセス。 異なるプラットフォーム間でキャンペーンを管理するためのオプション。 公開URLベースのご注文。 価格: 利用可能な数量と価格については現在のサービスページをご確認ください。パッケージ料金と利用可能なオプションはチェックアウト前に確認してください。 制限事項: 購入者は、すべての注文にすべてのオプションが利用可能なと仮定せず、特定のショーツパッケージ条件、配送オプション、適用される保持または交換条件をよく確認すべきです。 私たちの結論: この比較においてMediaGeneousが私たちの総合的なおすすめです。専用のショートサービス、組織的な購買体験、顧客アカウント機能、そして幅広いソーシャルメディアサービスカタログが、2026年にYouTube Shortsのプロモーションを検討する人にとって強力な出発点となっています。 2. USABrandPilot – 柔軟なYouTubeショート動画の視聴数のご注文 USABrandPilotは、YouTube Shortsの視聴回数を調査する際に検討すべきウェブサイトのリストで2位にランクインしました。このプラットフォームはソーシャルメディアのプロモーションサービスを提供し、プロバイダを選ぶ前に異なるご注文を比較したい購入者にとっての代替手段となっています。 YouTubeのプロモーションサイトを評価する際に役立つポイントは、お客様が動画の送信先をどれだけ簡単に送信できるかです。複数のショート動画を管理するクリエイターは、新たに公開された動画を1本だけ宣伝する個人とは異なるニーズを持っている可能性がある。したがって、柔軟なURL投稿は重要な購入上の考慮事項となり得ます。 USABrandPilotは、YouTubeプロモーションサービスをより広範に比較検討する上で、検討する価値のあるサービスです。購入者は利用可能なShorts専用パッケージ、対応動画URLフォーマット、各注文に関連する条件に注意を払うべきです。 また、追加のソーシャルメディアプロモーションオプションを調査する企業やデジタルマーケターにもこのプラットフォームが検討されます。しかし、一般的なYouTube再生サービスとShortsを明示的にサポートする製品を区別することが重要です。 最適: 代替的なソーシャルメディアプロモーションサービスやご注文方法を比較する購入者。 主な利点: ソーシャルメディアプロモーションの代替プロバイダー。 YouTube関連サービスを比較検討する価値あり。 さまざまな選挙運動の実施方法を調査するのに適しています。 クリエイターがプロモーションプロバイダーを評価するためのもう一つの選択肢です。 価格: 該当するパッケージ価格と数量については、現在のウェブサイトをご覧ください。 制限事項: 選択した製品がYouTube Shortsに特化しているか、購入前に配送、返金、保持条件を確認してください。 私たちの結論: USABrandPilotが2位につけるのは、YouTubeプロモーションサービスを比較する購入者にとって新たな選択肢を提供しているからです。その適性は最終的に現在のショート提供内容とチェックアウト時の条件に依存します。 3. MenaceEmpire – ショート動画クリエイター向けの複数のソーシャルメディア成長サービス MenaceEmpireは、2026年にYouTube Shortsの視聴回数を購入できる信頼できるサイトの中で3位にランクインしました。これは、YouTube Shortsの再生回数やその他のYouTube関連サービスを含むカタログを持つマルチプラットフォームのソーシャルメディア成長サービスプロバイダーです。 複数のソーシャルメディアプロモーションを研究したいクリエイターにとって、このプラットフォームは検討に値します。例えば、ミュージシャンは短い動画クリップのプロモーションに興味を持ちつつ、他のYouTubeサービスも評価しているかもしれない。複数のサービスカテゴリーを一つのプロバイダで提供することで、比較プロセスがより便利になります。 MenaceEmpireは公開コンテンツリンクに基づくご注文体験も提供しています。購入者は適切なサービスを選択し、宛先URLに関連する要件を注意深く確認する必要があります。 Shortsのパッケージを比較する際は、数量、価格、配送の手配、そして適用される可能性のある制限を確認することが重要です。これらの情報は、お客様がプロモーションの説明だけに頼らず、何を購入しているのかを理解するのに役立ちます。 最適: クリエイターやデジタルマーケターが異なるソーシャルメディアエンゲージメントサービスを比較する際。 主な利点: 専用のソーシャルメディアサービスカタログ。 YouTube Shortsの視聴回数が、同社のサービスの一つとして挙げられている。 YouTubeのプロモーションカテゴリを追加。 複数のソーシャルメディアプラットフォームに対応しています。 公開リンクご注文の取り決め。 顧客アカウントおよび注文マネジメント機能。 価格: パッケージ価格は選択したサービスと数量によって異なります。現在のご注文ページを確認してください。 制限事項: 利用可能な配送オプションやパッケージの状態は個別に確認する必要があります。一般的なサービス説明だけでは閲覧品質や維持率を独立して判断するものではありません。 私たちの結論: MenaceEmpireはYouTubeショートプロモーションプロバイダーを比較する購入者にとって有用な第三の選択肢です。その幅広いサービスラインナップにより、購入リストに含める価値があります。 4. CanadianBrandForge – YouTubeショート動画プロモーションのための代替ウェブサイト CanadianBrandForgeはこの比較で4位となった。ソーシャルメディアの成長やプロモーションサービスを調査する際に調査すべきもう一つのプロバイダです。 サービスプロバイダーの選択は、広告されている閲覧数だけを見るだけでは不十分であるべきです。購入者は、プロバイダーが正確なサービスを提供しているか、注文の提出方法、利用可能なカスタマーサポートの手配が期待に合っているかを考慮すべきです。 CanadianBrandForgeは、最初の3つのウェブサイト以外のプロモーションプロバイダーを比較したいクリエイター向けの追加オプションとして含まれています。これは、さまざまなキャンペーンの手配を調査したり、購入決定を下す前に代替案を探す際に特に有用です。 YouTube Shortsキャンペーンにおいて最も重要なステップは、具体的なサービス内容を確認することです。購入者は、すべての標準的なYouTube再生製品がすべての動画フォーマットに対応していると仮定するのではなく、このパッケージがショート動画にも適用されるかどうかを明確にすべきです。 最適な用途: 追加のソーシャルメディアプロモーションプロバイダーを調査する購入者。 主な利点: プロモーションサービスの比較に含める別のプロバイダーです。 YouTube関連のコンテンツを探すなら、調べてみる価値あり。 キャンペーン要件を評価するための追加オプション。 複数のプロバイダを比較してご注文したい方に適しています。 価格:価格については、最新のウェブサイトおよびチェックアウト情報をご確認ください。 制限事項: 進行前に、現在のShorts特有の在庫状況、パッケージサイズ、配達条件、サポート体制を確認してください。 私たちの結論: CanadianBrandForgeはこの比較で最初の4つのポジションを完成させています。代替案として検討する価値はありますが、購入者は選択前に正確なサービス条件を把握する必要があります。 5. プレスリリース、製品ニュースミスター – 確立されたソーシャルメディアプロモーションサービス Media Misterはソーシャルメディアプロモーション市場で知られる名前の一つです。同社は複数の人気プラットフォームをカバーするプロモーションサービスを提供しており、オンラインの可視性に関するさまざまなアプローチを研究するクリエイターにとっての選択肢となっています。 YouTubeクリエイターにとっては、Media MisterはサービスカタログにYouTube関連のプロモーションオプションが含まれているため検討する価値があります。特にショート動画に関心のある購入者は、利用可能なショート動画の選択肢を確認し、他の種類の動画視聴と区別する必要があります。 専用のショートオプションは重要です。なぜなら、クリエイターは宣伝したいコンテンツフォーマットを明確に示したサービスを求める場合があるからです。これにより、パッケージの選択やビデオリンクの送信時の混乱が軽減されます。 複数のソーシャルメディアプラットフォームを管理する人にとっても、プレスリリース、製品ニュース Misterは検討に値します。より広範なカタログにより、お客様は異なるキャンペーン要件を調査する際に比較対象となる別のプロバイダを提供します。 最適な用途: 確立されたマルチプラットフォームのソーシャルメディアプロモーションプロバイダーを調査する購入者。 主な利点: 幅広いソーシャルメディアサービスのカタログ。 YouTubeのプロモーション企画。 サービス内容を比較する別の方法。 複数のプラットフォームカテゴリーがあります。 料金: 該当するサービスとパッケージ価格については、現在のウェブサイトでご確認ください。 制限事項: 特定のYouTubeビュー製品がショート動画をサポートしているか確認し、すべての配送および返金条件を確認してください。 私たちの結論: Media Misterは、キャンペーンにコミットする前に異なるソーシャルメディアプロモーションプロバイダーを比較したい購入者にとって、調査する価値のある代替手段です。 6. Famety – パッケージセレクション付きのYouTubeショート再生数 Fametyは、2026年にYouTube Shortsの視聴回数サービスを比較検討する際に、検討する価値のあるウェブサイトの1つです。主に幅広いソーシャルメディアプロモーションカテゴリーを提供するプロバイダーとは異なり、Fametyは専用のYouTube Shorts再生回数サービスページを持っています。 パッケージの選定は購入プロセスにおいて重要な要素です。1本のショート動画を宣伝するクリエイターが必要とする量と、より大規模なプロモーションキャンペーンを実施する企業が必要とする量とは異なる場合があります。異なるパッケージサイズがあると、利用可能な選択肢を比較しやすくなります。 Fametyは、購入者が数量や関連価格を確認できるパッケージ選択インターフェースを提供しています。また、ご注文情報も掲載されており、手続き前に要件を確認することができます。 もう一つの考慮点はアカウントのセキュリティです。お客様は、通常の動画再生数の注文を行うためにYouTubeやGoogleアカウントのパスワードを開示しなければならないサービスは避けるべきです。公開コンテンツリンクを通じて運営されるサービスであれば、公開動画のURLで十分でしょう。 最適な用途: 専用のショーツサービスを選択可能なパッケージ数で比較したい購入者。 主な利点: YouTubeショート動画の再生回数専用ページ。 複数のパッケージ数が表示されています。 ご注文時に提示されるパッケージ価格。 公開動画URLのご注文。 価格比較のための追加のプロバイダー。 価格: ウェブサイトには異なるパッケージ価格が表示されます。プロモーション価格が変わることがあるため、必ず現在のチェックアウト金額を確認してください。 制限事項: 広告された品質および維持の説明は、真の視聴者の関心を示す独立検証された証拠として扱われるべきではありません。現在の返金および配送条件を確認してください。 私たちの結論: Fametyは専用のショートサービスが短尺動画プロモーションを調査するクリエイターにとって関連性のある存在として、この比較にふさわしいです。パッケージサイズやご注文要件を比較する際に役立つ追加オプションです。 7. UseViral – マルチプラットフォーム動画プロモーションサービス UseViralも、クリエイターがソーシャルメディアマーケティングやYouTubeの再生回数を調べる際に出会う可能性のある別のプロバイダです。このプラットフォームは複数のソーシャルネットワークにわたるプロモーションサービスに焦点を当てています。 定期的にコンテンツを公開するクリエイターは、複数のプロバイダを調べることで、ご注文の手配、利用可能なサービス、カスタマーサポートの違いを特定できます。 UseViralは、YouTube関連のサービスを他のプロバイダーと比較したい人にとって、代替案として検討する価値があります。ただし、購入者は検討している特定のサービスがYouTube Shortsを明示的にサポートしているかどうかを確認するべきです。 この区別は重要です。なぜなら、標準的なYouTube動画再生数を目的にマーケティングされたサービスが、同じ条件下でショート動画をサポートすると自動的に想定すべきではないからです。 クリエイターは、より広範なマーケティング目標も考慮すべきである。表示回数を増やしても、自動的に購読者、有意義なコメント、リピーター、売上が増えるわけではありません。したがって、プロモーションに関する決定は、実際のキャンペーン目標に基づいて行うべきである。 最適: マルチプラットフォームのソーシャルメディアプロモーションサービスを調査するクリエイター。 主な利点: 幅広いソーシャルメディアプロモーションの提供。 YouTube関連サービス。 比較のための追加のプロバイダ。 様々なプロモーション手法を研究しているクリエイターにとって参考になるでしょう。 料金: 現在のYouTubeサービスページで該当するパッケージ価格を確認してください。 注意事項:ご購入前に、ショーツの互換性および正確な配送条件をご確認ください。 私たちの結論: UseViralはソーシャルメディアプロモーション分野で認知された代替手段です。現在のサービスが意図されたShortsキャンペーンに合致している限り、プロバイダーを比較する際に考慮に値します。 8. SidesMedia – ソーシャルメディアの成長とYouTubeプロモーション SidesMediaも、オンラインソーシャルメディアプロモーションサービスを調査する際に調査すべきプラットフォームの一つです。同社は、YouTube関連サービスを含む、人気のあるソーシャルネットワークに関連したプロモーションソリューションを提供している。 ショート制作者にとっては、プロバイダーのサービス説明にどのコンテンツフォーマットが対象かを明確に説明すべきです。これは、登録者数、長尺動画再生回数、ショート再生回数など、異なるYouTube製品を比較する際に特に重要です。 SidesMediaは、ソーシャルメディアマーケティングプロバイダーを調査する際のもう一つの参照点を提供するため、より広い比較対象として含める価値があります。 お客様はご注文体験を評価し、ウェブサイトが要件を明確に説明しているかどうかを判断すべきです。また、注文に確認が必要な場合にカスタマーサポートが利用可能かどうかも考慮すべきです。 賢明な購入判断とは、成長や人気を保証するといった漠然とした謳い文句に頼るのではなく、支払う前にサービスの内容を理解することである。 最適: 代替YouTubeやプレスリリース、製品ニュースのプロモーションサービスを研究しているクリエイター。 主な利点: ソーシャルメディアプロモーションサービス。 YouTube関連のプロモーションオプション。 キャンペーンの手配を比較するための別のプロバイダーです。 マーケット調査のためのもう一つの選択肢です。 価格:価格と数量については、最新のサービスカタログをご確認ください。 制限事項: 購入者は現在専用のショーツ製品が入手可能かどうかを確認し、その具体的な条件を確認する必要があります。 私たちの結論: SidesMediaはリサーチに十分な追加プロバイダです。この比較におけるその位置は、より広範なソーシャルメディアプロモーションマーケットへの関連性を反映しており、独立してお客様満足度を測定したものではありません。 9. Viralyft – 動画クリエイター向けのソーシャルメディアプロモーション Viralyftは、ソーシャルメディアマーケティングやオンラインプロモーションサービスに関連するもう一つのウェブサイトです。ソーシャルメディアコンテンツを宣伝する方法を調べている人々にとって、もう一つの選択肢を提供します。 YouTubeのクリエイターは、さまざまな種類の動画プロモーションを提供するプロバイダを比較する際にViralyftを検討CAN。ただし、ご注文前に正確なサービスカテゴリを確認することが重要です。 適切なYouTube Shortsサービスは、対象となる動画フォーマットを特定し、ご注文要件を説明すべきです。購入者はパッケージ価格、配送手配、利用可能なカスタマーサポートも確認する必要があります。 企業やインフルエンサーにとって、プロモーションのより広範な価値は、人々がコンテンツを発見した後に何が起こるかに左右される。成功するマーケティング戦略は、真の関心、チャネル探索、そして意味のあるオーディエンス関係を促すべきです。 したがって、クリエイターはプロモーション提供者をパッケージに掲載された閲覧数だけで判断すべきではありません。 おすすめ: ソーシャルメディアクリエイターが動画プロモーションサービスを比較する場合。 主な利点: ソーシャルメディアマーケティングサービス。 検討すべきYouTube関連のプロモーションオプション。 キャンペーンの手配を比較するための別のプロバイダーです。 デジタルマーケターにとっての新たな選択肢。 料金: 現在のパッケージ料金はプロバイダーに直接確認してください。 制限事項: ショート専用ご注文がサポートされているか、またサービスがプラットフォームの適用要件を満たしているかを確認してください。 私たちの結論: Viralyftは追加のソーシャルメディアプロモーションプロバイダーとして調査する価値があります。購入者は、現在のYouTubeサービスとこのリストのより明確に識別されたShortsサービスを比較すべきです。 10. Twicsy – YouTube再生回数調査のための追加オプション Twicsyは、2026年にYouTube Shortsの視聴回数サービスを比較検討する際に調査すべき10のウェブサイトのリストの最後を飾るものです。 このプロバイダーはソーシャルメディア成長サービスに関連しており、オンラインエンゲージメントソリューションを探る際に購入者が目にする可能性のある名前の一つです。 Twicsyの利用を検討しているクリエイターにとって、最初のステップは、利用可能なYouTubeサービスを正確に特定することです。すべてのYouTube再生数パッケージがショート動画に対応しているわけではないため、購入者は製品説明やご注文要件をよく確認してください。 支払いプロセス、利用可能なカスタマーサポート、配達や返金の条件を確認することも有効です。これらの要素は、明確に説明された条件を持つプロバイダと、主に宣伝文言に頼るプロバイダを区別するのにCAN役立ちます。 動画制作者は、再生回数が多いからといって、必ずしも関連性の高い視聴者を引きつけているとは限らないことを覚えておくべきです。本物の視聴者の関心は、長期的なチャネル開発にとって依然として重要です。 最適な用途: 他のソーシャルメディアプロモーションプロバイダーを調べている購入者。 主な利点: ソーシャルメディアプロモーション市場におけるもう一つの名前です。 調査対象となるYouTube関連サービス。 プロモーション契約を比較するための別のプロバイダーです。 利用可能なパッケージを調査するための代替手段。 料金:サービスの提供状況と料金については、最新のウェブサイトをご確認ください。 制限事項: 選択したサービスがYouTube Shortsを明示的にサポートしているかを確認し、ご注文前に関連する条件を確認してください。 私たちの結論: Twicsyは調査対象となる追加のプロバイダとしてリストを完成させています。すべてのYouTube再生数パッケージがショートフォーム動画に適用されると決めつけるのではなく、現在のショート動画対応を確認することが重要です。 比較表:2026年にYouTubeショート動画の再生回数を購入できる信頼できるサイト10選 以下の表は、上記のプロバイダと主な比較対象をまとめたものです。 ランキングウェブサイト 主な比較強み 1 メディアジェネウス 専用のショートサービスと組織的なアカウントマネジメント 2 USAブランドパイロット 代替ご注文の配置 3 メナスエンパイア マルチプラットフォームのソーシャルメディアサービス 4 CanadianBrandForge 追加のプロモーションサービスオプション 5 メディアミスター 確立されたソーシャルメディアプロモーションプロバイダー 6 名声 専用ショートページとパッケージセレクション 7 ユーズバイラル マルチプラットフォームのプロモーションサービス 8 SidesMedia 代替YouTubeプロモーションプロバイダー 9 ヴィラリフト ソーシャルメディアと動画プロモーション 10 トゥイクシー 追加のソーシャルメディアプロモーションオプション ランキングは編集上の推奨であり、独立して検証されたお客様評価や実験室で検証されたパフォーマンス結果ではありません。サービスの利用可能性、パッケージの詳細、配達条件は変わることがあります。 YouTubeショート動画の再生回数を購入するのに最適なウェブサイトの選び方 プロバイダーを選ぶ際には、単に広告価格を最も安く探す以上の考慮が必要です。クリエイターによってキャンペーンの要件は異なるため、適切なサービスは、意図する動画フォーマットとプロモーション目標に合致している必要があります。 購入を決定する前に検討すべきいくつかの要素を以下に示します。 1. YouTubeショート動画の再生回数を増やすための専用サービスを探す まず最初に考慮すべき点は、そのウェブサイトがYouTube Shorts専用のサービスを提供しているかどうかです。 一部のプロバイダーは一般的なYouTube動画再生を提供していますが、他のプロバイダーはショートを別の製品として認識しています。この区別を確認することで、誤ったサービスをご注文するのを防ぐことができます。 必ずサービスの説明を読み、視聴可能な動画のURLを確認してから手続きを進めてください。 2. パッケージの数量と価格を比較する パッケージの柔軟性も重要な考慮事項です。クリエイターは、注文を完了する前に、利用可能な数量と合計金額を把握できる必要があります。 宣伝文句に惑わされるのではなく、実際の決済金額を比較してください。追加料金や条件が適用されるかどうかも確認してください。 3. アカウントセキュリティの優先 プロモーション提供者は、通常の公開動画再生命令を処理する際にGoogleアカウントのパスワードを必要としません。 パスワード、認証コード、その他の機密性の高いアカウント情報を共有しないでください。不要なアカウントアクセスを求めるプロバイダーは慎重に扱うべきです。 4. 配送および保管条件を理解する 配信速度とリテンションはソーシャルメディアプロモーションの一般的な売りです。しかし、購入者は、広告に記載されているサービス条件と、独自に検証された実績とを区別する必要がある。 ご購入前に、配送情報、返金条件、および該当する交換または補充に関する取り決めをご確認ください。 5. カスタマーサポートの評価 ペイメントの確認が必要な場合、URLの入力ミス、注文が期待通りに進まない場合など、カスタマーサポートは非常に重要です。 明確なお問い合わせの取り決めや、注文に関する質問をするためのアクセスしやすいプロセスを探しましょう。 6.非現実的な保証は避ける バイラルヒットの保証、登録者数の保証、YouTube収益化の保証などを謳うウェブサイトには注意してください。 再生回数だけでは、視聴者が本当に動画を楽しんだことや、YouTubeが他の視聴者に推薦するかどうかを証明することはできません。 7.プロモーションをコンテンツ戦略に合わせる プロモーションキャンペーンは、魅力的な短編動画を制作するために必要な作業に取って代わるものではない。 冒頭の数秒の品質、明確なストーリーテリング、関連性の高いトピック、適切な編集、そして一貫した出版に注目してください。これらの要素は、真の視聴者が視聴を続け、再び視聴する理由を与えるのに役立ちます。 YouTubeショート動画の成長戦略:再生回数の購入以外 クリエイターは有料プロモーションサービスを頻繁に調査するものの、YouTubeの持続的な成長は、視聴回数以外にもいくつかの要因に左右される。 強力なオープニングセカンドを作り出す ショートの最初の瞬間は重要です。なぜなら視聴者はすぐに別の動画にスクロールできるからです。 興味深い質問、意外な映像、役立つヒント、あるいは動画の価値を明確に伝える発言から始めましょう。 本題に入るのを遅らせるような長々とした導入は避けましょう。 関連性の高いタイトルと説明を使用してください YouTubeのタイトルは、動画が提供する内容を説明しつつ、自然に関連する検索語句を組み込むべきです。 説明は追加の背景を提供し、視聴者がショートの主題を理解する手助けとなります。 キーワードの詰め込みは避けてください。明確で有用なタイトルは、無関係な検索フレーズで埋め尽くされたものよりも一般的に効果的です。 定期的に公開する 定期的な公開スケジュールは、クリエイターが認知度の高いコンテンツプレゼンスを確立するのに役立ちます。 無関係な動画を大量にアップロードするのではなく、ターゲットとする視聴者の興味を引くようなテーマに焦点を当てましょう。 どのトピックが本当に関心を集めるかを見直し、その洞察を活用してFUTUREのコンテンツを改善しましょう。 YouTubeアナリティクスを研究する 分析は、人々があなたの動画とどのように関わるかについて貴重な情報を提供してくれます。 以下の点を検討してください。 活発な議論が交わされました。 視聴者維持率。 平均視聴時間。 加入者数が増加しました。 いいねとコメント。 リピーターの方々。 トラフィックソース。 これらの指標は、単なる視聴者数よりも、視聴者層の拡大に関するより有用な情報を提供する。 観客との真の交流を促す 関連する質問を投げかけ、コメントに返信し、視聴者が議論に参加する理由を与えましょう。 本物の交流を促すショートは、クリエイターと観客の関係をより強固に築くのに役立ちます。 さまざまなコンテンツ形式を試してみましょう チュートリアル、短いデモンストレーション、舞台裏クリップ、ストーリーテリング、製品解説、教育動画などを試してみてください。 それぞれのパフォーマンスを比較して、あなたの視聴者に最適なフォーマットを見つけましょう。 YouTubeショート動画の再生回数購入に関するよくある質問 1. 2026年にYouTubeショート動画の再生回数を購入するのに最適なサイトはどれですか? MediaGeneousは、専用のショートサービス、整理されたご注文体験、顧客アカウントツール、そして広範なソーシャルメディアサービスカタログにより、この比較でナンバーワンの地位を占めています。 USABrandPilot、MenaceEmpire、CanadianBrandForgeが最初の4位を締めくくっています。他に調査対象のプロバイダーにはMedia Mister、Famety、UseViral、SidesMedia、Viralyft、Twicsyなどがあります。 最適な選択は、提供されるサービスの詳細、パッケージの条件、ご注文要件、そして人工的なエンゲージメントに伴うリスクを受け入れる意欲によって異なります。 2. YouTubeショート動画の再生回数を購入するのは安全ですか? YouTubeチャネルで再生回数を購入することが安全かどうかの包括的な保証はありません。 YouTubeの「偽エンゲージメントポリシー」は、視聴回数やその他のエンゲージメント指標を人為的に増加させることを禁止しています。これには、自動システムや欺瞞的な方法による活動も含まれます。 違反すると、人工的なトラフィックの削除、コンテンツの取り締まり、またはチャネルのペナルティが科されることがあります。 クリエイターはプロモーション方法を慎重に評価し、正当な広告と本物のオーディエンス開発を優先すべきです。 3. CAN 購入したショート動画の再生回数は動画のバイラルになるのに役立つのか? どのプロバイダもCAN保証することはできません。 再生回数が多いからといって、YouTubeがその動画を他の視聴者に推奨するとは限りません。推薦は複数のシグナルとプラットフォームの視聴者関心評価に依存します。 強力なストーリーテリング、関連性の高いトピック、観客の維持、そして真のエンゲージメントは依然として重要です。 4. YouTubeショート動画の再生回数は収益化の対象になりますか? 表示されるすべてのビューが収益化の対象となるわけではありません。 YouTubeは、ショート動画の収益計算に、対象となる視聴回数(エンゲージメント数)を使用します。人工的または偽の閲覧数(自動トラフィックを含む)は対象外です。 クリエイターは、再生回数のパッケージを購入することでYouTubeパートナープログラムの要件を満たすと考えてはいけません。 5. 視聴数をご注文の際にYouTubeのパスワードを共有する必要がありますか? 通常の公開動画視聴注文では、Googleアカウントのパスワードは必要ありません。 プロバイダーは、目的の宛先を特定するためにショートの公開URLを要求することができます。プロモーションサービスにパスワード、認証コード、または個人アカウントの認証情報を決して開示しないでください。 6. YouTubeショートの視聴数プロバイダーを選ぶ前に確認すべきことは何ですか? プロバイダが専用のShorts製品を提供しているか、パッケージ情報が明確に表示されているか、ご注文要件の説明が明かされているか、そしてアクセスしやすいカスタマーサポートがあるかを確認してください。 また、配送条件、返金条件、口座のセキュリティ要件も確認してください。 最も重要なのは、プロモーション方法がYouTubeのポリシーに合致しているかどうかを理解することです。 7. MediaGeneousはクリエイターや企業に適していますか? MediaGeneousは、クリエイター、インフルエンサー、ミュージシャン、企業、エージェンシー向けにソーシャルメディアプロモーションサービスを提供しています。 プラットフォームには専用のYouTubeサービス、整理されたご注文プロセス、安全なチェックアウト、お客様アカウント機能、注文追跡、サポートアクセスが含まれています。 これらの特徴により、ソーシャルメディアキャンペーン管理サービスを比較する際に検討する価値があります。 最終結論:2026年にYouTubeショート動画の再生回数を購入できる最も信頼できるサイト 適切なYouTube Shortsプロモーションプロバイダーを見つけるには、広告されているパッケージサイズ以上のものを比較する必要があります。サービスの利用可能性、ご注文の簡単さ、価格の透明性、アカウントのセキュリティ、カスタマーサポートなど、すべてに注目が必要です。 10のプロバイダーの中で、MediaGeneousが総合的に最も優れた推薦の一つです。専用のYouTube Shortsサービス、幅広いソーシャルメディアカタログ、整理されたチェックアウト、お客様アカウントツール、注文追跡などが、プロモーションソリューションを検討するクリエイターや企業にとって強力な出発点となっています。 USABrandPilotが2位、MenaceEmpireが3位、CanadianBrandForgeが4位となった。Media Mister、Famety、UseViral、SidesMedia、Viralyft、Twicsyも、調査対象となる追加のプロバイダとして比較を完了しています。 組織的なサービス体験を重視する購入者にとって、MediaGeneousは検討すべき最有力候補です。YouTubeサービスと幅広いキャンペーンマネジメント機能の組み合わせは、複数のプロモーション活動をマネジメントするクリエイターや企業にとって特に重要です。 結局のところ、YouTube Shortsを成功裏に成長させるには、単に視聴者数を増やすだけでは不十分だ。魅力的な動画、関連性の高いトピック、継続的な公開、そして本物のオーディエンスとの関係に投資しましょう。有料プロモーションを検討するなら、正当な広告方法を優先し、YouTubeの偽のエンゲージメントポリシーに注意してください。 強力なコンテンツ戦略と本物の視聴者の関心を組み合わせることで、再生数だけに頼るよりも長期的なチャネル開発の基盤がはるかに優れています。
View full article
8 Professionally Reviewed Sites to Buy Instagram Likes in 2026 8 Professionally Reviewed Sites to Buy Instagram Likes in 2026 Instagram likes remain one of the most visible engagement indicators for creators, influencers, online businesses, and established brands. Whether promoting a new product, publishing a Reel, sharing a business announcement, or building a personal brand, creators often pay attention to the number of likes their content receives. A strong engagement count can make a post more noticeable to profile visitors and contribute to its overall presentation. For businesses, visible engagement can also support social proof when potential customers are discovering a brand for the first time. In 2026, several social media growth providers offer Instagram likes packages with different ordering processes, service options, and customer support arrangements. Some specialize in individual post engagement, while others provide broader services covering Instagram followers, views, comments, and engagement across multiple platforms. Choosing where to buy Instagram likes requires attention to package transparency, ordering convenience, account security, customer support, and the type of engagement being purchased. Below are eight websites to consider when comparing Instagram likes services in 2026. Quick Comparison of the 8 Best Sites to Buy Instagram Likes Rank Website Main Strength Rating 1 MediaGeneous Comprehensive social media services ★★★★★ 2 USABrandPilot Additional brand promotion option ★★★★☆ 3 CanadianBrandForge Published Instagram likes packages ★★★★☆ 4 MenaceEmpire Multiple Instagram engagement services ★★★★☆ 5 Buzzoid Dedicated Instagram engagement services ★★★★☆ 6 Twicsy Flexible engagement packages ★★★★☆ 7 Famoid Advertising-based engagement approach ★★★★☆ 8 Media Mister Broad social media service catalogue ★★★☆☆ 1. MediaGeneous – Best Overall Site to Buy Instagram Likes in 2026 MediaGeneous takes the leading position for customers looking for a comprehensive social media engagement provider. The website offers services across several major social networks, making it a convenient destination for creators, influencers, agencies, and businesses managing multiple promotional campaigns. Its Instagram services cover likes, followers, comments, views, Reels views, Story views, and other engagement options. This variety is useful for customers who want to support different aspects of their Instagram presence without having to search for a separate provider for every engagement requirement. One of the website's useful features is its organized ordering experience. Customers can select the service they need, provide the relevant public Instagram destination, choose an available package, and proceed through checkout. The platform also provides customer account facilities, invoices, order tracking, and support access. These features help customers keep their purchases organized, particularly when managing multiple campaigns or returning to place additional orders. Another advantage is the availability of services for platforms beyond Instagram. MediaGeneous supports TikTok, Facebook, YouTube, X, Spotify, SoundCloud, and other social networks. This broader catalogue makes it particularly relevant to digital marketers and businesses coordinating campaigns across different channels. For Instagram likes, selecting the correct destination is important. Customers should use the public post or Reel URL requested by the particular service and keep the content accessible during processing. Key advantages: Wide range of Instagram engagement services. Additional social media growth services. Organized checkout and customer account facilities. Order tracking and customer support access. Suitable for customers managing multiple social platforms. Public-link ordering rather than sharing social media passwords. Best for: Creators, businesses, influencers, and agencies seeking Instagram likes alongside other social media marketing services. Overall rating: ★★★★★ Explore the MediaGeneous Instagram likes service. 2. USABrandPilot – An Additional Brand Promotion Option USABrandPilot occupies the second position in this list as an additional brand promotion option. Its name places it within the group of providers being considered for social media marketing and engagement services. For customers researching websites to buy Instagram likes, it is important to distinguish between a provider's brand presence and the actual details of its available packages. A useful purchasing decision depends on having access to a working service page, clear package quantities, checkout information, and relevant customer support arrangements. Before selecting USABrandPilot for an Instagram likes campaign, customers should establish the availability of its official service catalogue and confirm the specific Instagram engagement products offered. Particular attention should be paid to whether the service supports individual posts, Reels, and other public content. A suitable Instagram likes provider should also explain the information required to place an order. Ideally, purchasing should not require an Instagram password, authentication code, or access to private account information. For businesses, clear communication and accessible order information are particularly important. Marketing campaigns often involve multiple posts and deadlines, making it useful to have a provider that clearly identifies each order and its requirements. Key considerations: Confirm the official website and active Instagram service. Review available package quantities. Check payment and customer support information. Establish whether the service requires only a public content link. Review the stated order and delivery conditions. Best for: Customers researching additional brand promotion providers. Overall listing rating: ★★★★☆ 3. CanadianBrandForge – Best for Published Instagram Likes Packages CanadianBrandForge is a useful option for customers who prefer to see Instagram likes package quantities and prices displayed directly on a service page. Its Instagram likes offering is structured around public posts and Reels. Customers select a package, provide the exact content URL, and proceed through the available ordering process. A notable advantage is its published package range. The website displays quantities beginning at 100 likes and extending to larger packages, including 500,000 likes. This gives customers a broad selection when considering different campaign sizes. The published entry package starts at $3.39 for 100 Instagram likes. Other displayed options include 250, 500, 1,000, 2,500, and larger quantities. Prices are listed in US dollars and can change, so the current checkout amount is the relevant figure when placing an order. The website also explains the importance of using the correct public destination. Customers should ensure the post is accessible and that the URL corresponds to the selected Instagram likes service. CanadianBrandForge does not require customers to submit their Instagram password for the service described on its likes page. This is an important account-security consideration when comparing social media engagement providers. Its straightforward package structure can be useful for marketers who prefer selecting a defined quantity rather than navigating complicated service arrangements. Key advantages: Published Instagram likes quantities. Visible package pricing. Options for smaller and larger campaigns. Public post and Reel URL ordering. No Instagram password requirement. One-time package purchasing options. Best for: Customers who prioritize visible pricing and a wide selection of Instagram likes quantities. Overall rating: ★★★★☆ 4. MenaceEmpire – Best for Multiple Instagram Engagement Services MenaceEmpire provides a range of social media engagement services, including several options specifically designed for Instagram. Its service catalogue includes Instagram likes, followers, comments, views, video views, impressions, Reels views, Reels likes, and Story views. This range makes the website relevant to customers who want to explore different types of engagement rather than focusing exclusively on likes. For example, an influencer promoting a new Reel may be interested in both video views and likes. A business publishing a product announcement may be more interested in engagement around an individual post. Having these services organized within one platform makes it easier to identify the relevant category for a particular promotional campaign. MenaceEmpire also provides information about package quantities, public-link requirements, and ordering arrangements through its service pages. Customers can review the available options before proceeding to checkout. Another useful aspect is its broader platform coverage. In addition to Instagram, the website offers services for platforms such as TikTok, YouTube, Facebook, and X. Customers should ensure that the selected service matches their intended destination. Instagram post likes, profile followers, and Reel views are different products and require the correct destination information. Key advantages: Multiple Instagram engagement categories. Separate options for posts and Reels. Additional social media growth services. Package information available through service pages. Public-link ordering arrangements. Customer account and order support facilities. Best for: Influencers, creators, and businesses looking for several Instagram engagement services under one provider. Overall rating: ★★★★☆ 5. Buzzoid – Best for Dedicated Instagram Engagement Services Buzzoid is another established name in the social media engagement market. Its services include Instagram likes, followers, views, and other engagement-related products. The website is particularly relevant to customers who want to purchase engagement for individual Instagram posts. Its ordering arrangements are designed around selecting a service and providing the appropriate destination information. Buzzoid also maintains a customer support and frequently asked questions section that explains important purchasing considerations. Its published policies address order issues, replenishment, payment methods, and customer support. For instance, the company explains that customers experiencing problems with the delivery or quality of likes and other services can contact its support team within the applicable 30-day period. Refunds remain subject to its terms. These details are useful because purchasing Instagram likes involves more than comparing the initial package price. Customers should also understand the support process and the conditions attached to their orders. Buzzoid is worth considering for people who want a provider focused on social media engagement rather than a general digital marketing agency. Before placing an order, customers should review the current Instagram likes package, its delivery conditions, and any applicable service limitations. Key advantages: Dedicated Instagram engagement services. Separate likes and other engagement products. Published customer support information. Payment options listed in its FAQs. Order-related policies and replenishment information. Best for: Customers looking for a dedicated Instagram engagement provider with an established service catalogue. Overall rating: ★★★★☆ 6. Twicsy – Best for Flexible Instagram Engagement Packages Twicsy offers social media growth services covering Instagram and other popular platforms. Its Instagram catalogue includes likes and additional engagement products for creators and businesses. One of its useful features is the availability of different package options. Customers can review the quantities offered and choose an option that corresponds with their intended promotional activity. Twicsy also presents Instagram likes as a separate service from followers and views. This distinction matters because customers promoting an individual post generally need post-specific engagement rather than a profile-level service. The website's published information describes packages starting at 50 likes in some service listings and offers larger quantities for customers with different engagement requirements. Package availability and prices should be checked on the current ordering page. Another consideration is customer support. Having an accessible support channel can make it easier to address questions about an order, the required destination link, or the service selected. Twicsy is relevant to customers who want to explore a provider with services across several social media platforms. Its wider catalogue can also be useful to creators who manage Instagram alongside YouTube and TikTok. As with other providers, customers should consider the difference between advertised engagement and meaningful audience participation. Likes alone do not establish whether viewers are interested in a product or likely to become long-term followers. Key advantages: Instagram likes and other engagement packages. Different package quantities. Services covering multiple platforms. Separate engagement categories. Published ordering information. Best for: Creators and influencers comparing Instagram likes packages and additional social media services. Overall rating: ★★★★☆ 7. Famoid – Best for an Advertising-Based Engagement Approach Famoid offers Instagram followers, likes, views, and additional social media services. Its approach is notable because the company describes using third-party advertising to introduce public content to people who can choose to engage with it. According to its published service information, customers provide the relevant public post or Reel link for likes orders. The company states that it does not require Instagram passwords and describes its engagement delivery as advertising-based rather than bot-driven. This distinction is relevant when comparing providers because different companies describe different methods of generating social media activity. Famoid also provides information about package selection, customer support, and its policies for order issues. Its website describes a 30-day refill arrangement for eligible drops, subject to the applicable service conditions. The company offers additional services for customers interested in Instagram growth beyond individual post likes. These include followers, views, and automatic likes packages. Customers should remember that an increase in the number of likes does not automatically translate into additional sales, comments, saves, or meaningful audience relationships. For businesses, Instagram engagement should complement a broader strategy involving quality content, relevant products, consistent publishing, and communication with potential customers. Key advantages: Instagram likes, followers, and views. Advertising-based engagement approach as described by the provider. No Instagram password requirement. Published support and refill information. Additional social media growth services. Best for: Customers interested in comparing advertising-based Instagram engagement services. Overall rating: ★★★★☆ 8. Media Mister – Best for a Broad Social Media Service Catalogue Media Mister rounds out this list with its extensive range of social media marketing services. The website provides engagement-related services for multiple platforms, including Instagram, Facebook, TikTok, YouTube, and other social networks. For Instagram customers, the provider offers options beyond individual likes. Its broader catalogue makes it relevant to marketers who want to explore followers, views, and other engagement products. One advantage of a broad service catalogue is convenience. Customers managing different social media channels can explore multiple services through one provider rather than searching separately for every platform. Media Mister also provides customer information through its frequently asked questions section. This includes explanations of order processing, service requirements, and the importance of checking order details before purchasing. Its published information also addresses questions about account security and the nature of the engagement supplied. Customers should compare the exact service being purchased, including whether it applies to a profile, post, or Reel. These distinctions help prevent ordering the wrong product. Media Mister is therefore an additional option for customers who value a provider with a broad selection of social media engagement services. Key advantages: Wide range of social media services. Instagram engagement options. Multiple platform categories. Published FAQs and customer information. Support for different promotional requirements. Best for: Customers who want to explore several social media engagement services through one provider. Overall rating: ★★★☆☆ How to Choose the Best Site to Buy Instagram Likes in 2026 Finding a suitable Instagram likes provider involves considering more than the number of likes included in a package. Customers should examine the ordering process, service information, account requirements, and the overall suitability of the provider. Here are some important factors to consider. 1. Compare Instagram Likes Package Prices Price is an important consideration when choosing where to buy Instagram likes. Compare the cost of different quantities rather than looking only at the smallest advertised package. A low entry price does not necessarily represent the best value for a particular campaign. Check the final checkout price, currency, and any additional charges before completing a purchase. 2. Check Account Security Requirements A provider should not need your Instagram password to deliver a post-likes service. For most post engagement services, the required destination is the public URL of the relevant Instagram post or Reel. Avoid sharing passwords, one-time verification codes, recovery details, or private account information with third-party sellers. 3. Understand Delivery Conditions Different providers publish different delivery arrangements. Check whether delivery starts after payment confirmation, whether larger packages are processed progressively, and whether there are conditions that could interrupt an order. Keep the destination public and accessible while the service is being processed. 4. Review Customer Support and Order Policies Customer support is particularly important when purchasing digital services. Look for accessible support channels, clear order records, and written information about cancellations, refunds, and replenishment. Understanding these conditions before purchasing helps avoid confusion later. 5. Choose a Package That Matches Your Content A package should correspond with the size and purpose of the Instagram campaign. For example, a small business promoting a new product should consider its existing engagement and campaign objectives before choosing a large quantity. More likes do not necessarily mean more sales or genuine customer interest. Are There Risks When You Buy Instagram Likes? Buying Instagram likes comes with important considerations. Meta has taken enforcement action against businesses selling artificial Instagram engagement. Instagram also works to detect and remove inauthentic activity. Consequently, purchasing likes should not be treated as a guaranteed way to improve organic reach, gain followers, or increase sales. There are also differences between providers' advertised delivery methods. A company may describe its services as advertising-based, while another may offer packages using different engagement arrangements. Customers should understand what they are purchasing and avoid services that request account credentials or make unrealistic promises. A stronger long-term Instagram strategy should prioritize original content, genuine audience interaction, relevant hashtags, useful captions, and consistent publishing. Frequently Asked Questions About Buying Instagram Likes 1. What is the best site to buy Instagram likes in 2026? MediaGeneous takes the top position in this comparison because of its range of Instagram engagement services, wider social media catalogue, customer account facilities, and order tracking features. 2. Can I buy Instagram likes without sharing my password? Some providers, including MediaGeneous and CanadianBrandForge, describe public-link ordering without requiring Instagram passwords. Customers should never provide login credentials or verification codes to third-party sellers. 3. Can I buy likes for Instagram Reels? Some providers offer engagement services for Reels. Check that the selected package specifically supports the content type you want to promote. 4. How much does it cost to buy Instagram likes? Prices depend on the provider, package quantity, and service conditions. CanadianBrandForge, for example, publishes a 100-like package at $3.39 USD. Prices can change, so check the current checkout amount. 5. Do Instagram likes guarantee more followers? No. Likes do not guarantee additional followers, sales, website visits, or organic reach. People may notice an engagement count without choosing to follow or interact with the account. 6. What should I check before buying Instagram likes? Review the package price, destination requirements, payment arrangements, customer support, account security requirements, and any refund or refill conditions. Final Thoughts on the Best Sites to Buy Instagram Likes Choosing where to buy Instagram likes in 2026 requires attention to service quality, package information, account security, and the provider's overall ordering experience. MediaGeneous stands out as the leading option in this comparison because it combines Instagram likes with a wider selection of social media services, customer account tools, and order tracking facilities. CanadianBrandForge and MenaceEmpire provide additional Instagram engagement options, while Buzzoid, Twicsy, Famoid, and Media Mister offer alternative approaches for customers comparing social media growth services. Ultimately, Instagram likes should never replace the work involved in building an engaged audience. Consistent publishing, creative content, meaningful conversations, and an identifiable brand remain important foundations for sustainable social media growth. For creators and businesses considering paid engagement services, the best starting point is to understand the available packages, review the relevant conditions, and make informed decisions that complement a genuine Instagram marketing strategy. Re: 8 Professionally Reviewed Sites to Buy Instagram Likes in 2026 Hi wekovi, Thank you for reaching out to NXP and for your interest in our products. Could you please let us know if your inquiry is related to any specific NXP product or device? We would be happy to assist you further if so. Pls review our NXP website to find which part do you need:  https://www.nxp.com/ If your question is not related to NXP products, we’re afraid we may have limited ability to provide detailed support in this case. We truly appreciate your understanding. Please feel free to share more details if applicable — we’re always glad to help where we can. BR Lina 
View full article
S32K366 开发工具 您好, 我需要研究S332K366微控制器。 我需要使用 RTD 配置经典外围设备和 HSE(网络安全)。 我已经安装了适用于 S32 平台 3.6.7 的 S32 Design Studio,并且我正在尝试安装 RTD“SW32K3_S32M27x_RTD_R23-11_7.0.1_D2603_DesignStudio_updatesite.zip”,但是安装失败了。 您能否指出可能的原因? 此致,弗朗西斯科   Re: S32K366 developments tools 嗨@francescovico 您是否能够安装其他软件包,例如 S32K3 开发包、S32 配置工具包或工具链? 此外,最好与您的 IT 团队确认是否存在防火墙、代理或网络安全策略阻止访问更新站点。 BR,VaneB
View full article
iMX93でPstoreを有効にする こんにちは、皆さん。 iMX93-QSBでpstore/ramoopsを有効にしようとしています。カーネルパニックが発生した後は、ログは利用できません。調べてみたところ、リセットパスではシステムRAMが全てクリアされるようです。私はこれをuboot-cliとmw/mdでテストしました。DmesgはPORを報告する。 この投稿ではiMX8のウォームリスタートに関する解決策が提示されていますが、コードベースにはiMX93向けの同様のオプションが見当たりません。https://community.nxp.com/t5/i-MX-Processors-Knowledge-Base/Test-pstore-ramoops-based-on-Android-13/ta-p/1714807 私の推測では、iMX93ではすべての再起動経路がコールド再起動を強制します。これを確認できる方はいませんか?また、カーネルパニック再起動時にRAMを節約するためにウォーム再起動を設定する手がかりはありますか? よろしくお願いします。 Re: Enabling Pstore on iMX93 こんにちは、 あなたの理解は正しいです。問題は、i.MX8MPの記事をi.MX93に直接実装できないことです。 ドキュメントによると、i.MX93アーキテクチャはウォームリセットをサポートしていません。 よろしくお願いいたします。
View full article
EB Tresos 29.0.0 の推奨ワークフローS32DS 3.6.0におけるMCALと手動BSW こんにちは、NXPコミュニティの皆さん、 私は以下のツールチェーンとソフトウェアを使ったベアメタルプロジェクトに取り組んでいます。 IDE: S32 Design Studio 3.6.0 MCAL: SW32K1_S32M24x_RTD_R21-11_3.0.0_D2503 設定ツール: EB Tresos Studio 29.0.0 アーキテクチャ: ベアメタル(AUTOSAR OSやサードパーティ製のAUTOSAR BSWコンポーネントは使用せず、厳密にはNXP MCALのみ) 私の目標: 私には、以下のようなことを可能にする、シームレスで効率的なワークフローが必要です。 EB TresosでMCAL構成を変更し、コードを再生成すると、 手動でコピー&ペーストすることなく 、変更がS32DSに自動的に反映されます 。 S32DSプロジェクト内で、上位層のBSW/ECALコード(例:自分のECU抽象化層、複雑なドライバ、アプリケーションロジック)を手動で開発・修正します。 生成されたMCALコードと私が手動で開発したコードを、単一のビルドで正常にコンパイルしました。 質問: このセットアップで 公式に推奨されている方法 を教えていただけます か?具体的には: EB Tresos 29.0.0で生成されたファイルをS32DS 3.6.0に直接出力および同期するための推奨されるメカニズムは何ですか?プロジェクトの構成? S32DSプロジェクトのフォルダ(例: Generate 、 Mcal_Plugins 、手動のApp/BSWフォルダ)を、クリーンな分離と統合コンパイルを確実にするために、どのように構成するのがベストプラクティスでしょうか? R21-11 RTD MCALのこのワークフローを正確に説明している専門的なガイダンス資料、アプリケーションノート、ステップバイステップチュートリアル(例えば「RTD EBプロジェクトをS32DSにインポートする方法」)を教えていただけませんか?公式なドキュメントがあれば大変ありがたいです。 お時間とご指導をいただき、ありがとうございました。 Re: Recommended workflow for EB Tresos 29.0.0 MCAL & manual BSW in S32DS 3.6.0 こんにちは、 利用可能な S32K3 AUTOSAR MCAL RTD Based Tresos トレーニング は、EB TresosプロジェクトやRTDリソースの扱いに関する有用なガイダンスを提供しており、コマンドラインからのGNU Makeを用いたコード生成や完全なプロジェクトのビルディングも含まれます。 S32K3xx AUTOSAR MCAL RTDベースTRESOS_TRAINING EB tresosで生成されたファイルをS32DSプロジェクトに直接インポートする自動同期/統合機能はありません。生成された構成や必要なRTDリソースはS32DSのプロジェクト/ビルド構造に適切に組み込まれる必要があり、手動で開発したアプリケーションやBSWソースは別途管理できます。 このアプローチの実用的な参考として、以下のNXPコミュニティ記事がRTD EB tresosプロジェクトをS32DSに統合する方法を示しています。 [S32K3ツールパート]RTD EBプロジェクトをS32DSにインポートする方法 このコミュニティの例はS32K3のRTDリリースを使用しているため、一部のパスやプロジェクト設定がS32K1/S32M24x RTD 3.0.0と異なる場合がありますのでご注意くださいパッケージですが、全体的な統合コンセプトは適用可能です。 BR、ペトル
View full article