delay between the boot loader and kernel splash screens

divyardharan · ‎01-07-2015

We are using sabresd iMx6Q board.The boot loader splash screen is showing for 7 sec.After that the lcd screen is blank for 20 sec before the kernal splash screen is loaded.Kindly help us to solve the delay between the boot loader and kernel splash screens.

jaymind · ‎01-07-2015

Hi Divya,

Is your splash screen custom image or default boot up logo ??

Can you please provide the kernel logs from start ?

in your kernel logs which you will provide me please marks when your screen appears, when screen becomes blank.

Just add line approximately above or below when you examine your kernel logs.

May be some configuration set and it was slowed due to it, I am not sure about it, but may be conclusion will come after your logs.

Regards

Jaymin D

divyardharan · ‎01-07-2015

Thank you for the response.

We are using custom image.

Kindly find the log below.

[LCD] Initializing LCD frambuffer at 27b00000

[LCD] Drawing the logo...

ipu_clk = 260000000

IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)

Framebuffer at 0x27b00000

mxcfb_init_fbinfo: 4 640 112 524

Framebuffer structures at: fbi=0x27602c50 mxcfbi=0x27602e60

allocated fb @ paddr=0x27B00000, size=3145728.

Channel already disabled 9

Channel already uninitialized 9

setup_disp_channel1 called

bpp_to_pixfmt: 16

init channel = 9

pixclock = 64998000l Hz

panel size = 1024 x 768

pixel clk = 64998000

setup_disp_channel2: 95ffcff 1024 768 2048 27b00000 27c80000

bpp_to_pixfmt: 16

initializing idma ch 23 @ 027005c0

IPU DMFC DP HIGH RES: 1(0,1), 5B(2~5), 5F(6,7)

ch 23 word 0 - 00000000 00000000 00000000 E0001800 000BFC7F

ch 23 word 1 - 04F90000 009EC000 20E3C000 F2C1FFC0 00082CA0

PFS 0x7, BPP 0x3, NPB 0xf

FW 1023, FH 767, Stride 2047

Width0 4+1, Width1 5+1, Width2 4+1, Width3 7+1, Offset0 0, Offset1 5, Offset2 11, Offset3 16

MXC IPUV3 configured

XRES = 1024 YRES = 768 BitsXpixel = 4

IPU_CONF = 0x00000660

IDMAC_CONF = 0x0000002F

IDMAC_CHA_EN1 = 0x00800000

IDMAC_CHA_EN2 = 0x00000000

IDMAC_CHA_PRI1 = 0x18800000

IDMAC_CHA_PRI2 = 0x00000000

IPU_CHA_DB_MODE_SEL0 = 0x00800000

IPU_CHA_DB_MODE_SEL1 = 0x00000000

DMFC_WR_CHAN = 0x00000090

DMFC_WR_CHAN_DEF = 0x202020F6

DMFC_DP_CHAN = 0x0000968A

DMFC_DP_CHAN_DEF = 0x2020F6F6

DMFC_IC_CTRL = 0x00000002

IPU_FS_PROC_FLOW1 = 0x00000000

IPU_FS_PROC_FLOW2 = 0x00000000

IPU_FS_PROC_FLOW3 = 0x00000000

IPU_FS_DISP_FLOW1 = 0x00000000

In: serial

Out: serial

Err: serial

Net: got MAC address from IIM: 00:10:2e:e0:00:02

FEC0 [PRIME]

### main_loop entered: bootdelay=3

### main_loop: bootcmd="run bootcmd_mmc"

Hit any key to stop autoboot: 3 2 1 0

********Power On Reset *****************

***Image validation flag=0******

*** Image Identifier flag is 0

Enabled Watch Dog Timer

System going to reboot within 120 sec, if watchdog not get feeding

file name=/

<2, 0, 204>

ext2fs read inode 2

ext2fs read 0 group descriptor (blkno 2 blkoff 0)

<4, 0, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 262 blkoff 128

<524, 128, 128>

ext2fs_read_block 00000205

<1034, 0, 8>

ext2fs_read_block 00000205

<1034, 8, 1>

iterate >.<

ext2fs read inode 2

ext2fs read 0 group descriptor (blkno 2 blkoff 0)

<4, 0, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 262 blkoff 128

<524, 128, 128>

<DIR> 1024 .

ext2fs_read_block 00000205

<1034, 12, 8>

ext2fs_read_block 00000205

<1034, 20, 2>

iterate >..<

ext2fs read inode 2

ext2fs read 0 group descriptor (blkno 2 blkoff 0)

<4, 0, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 262 blkoff 128

<524, 128, 128>

<DIR> 1024 ..

ext2fs_read_block 00000205

<1034, 24, 8>

ext2fs_read_block 00000205

<1034, 32, 10>

iterate >lost+found<

ext2fs read inode 11

ext2fs read 0 group descriptor (blkno 2 blkoff 0)

<4, 0, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 263 blkoff 256

<526, 256, 128>

<DIR> 12288 lost+found

ext2fs_read_block 00000205

<1034, 44, 8>

ext2fs_read_block 00000205

<1034, 52, 4>

iterate >home<

ext2fs read inode 14281

ext2fs read 7 group descriptor (blkno 2 blkoff 224)

<4, 224, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 57606 blkoff 0

<115212, 0, 128>

<DIR> 1024 home

ext2fs_read_block 00000205

<1034, 56, 8>

ext2fs_read_block 00000205

<1034, 64, 3>

iterate >mnt<

ext2fs read inode 36721

ext2fs read 18 group descriptor (blkno 2 blkoff 576)

<5, 64, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 147459 blkoff 0

<294918, 0, 128>

<DIR> 1024 mnt

ext2fs_read_block 00000205

<1034, 68, 8>

ext2fs_read_block 00000205

<1034, 76, 3>

iterate >etc<

ext2fs read inode 67321

ext2fs read 33 group descriptor (blkno 3 blkoff 32)

<6, 32, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 270339 blkoff 0

<540678, 0, 128>

<DIR> 1024 etc

ext2fs_read_block 00000205

<1034, 80, 8>

ext2fs_read_block 00000205

<1034, 88, 3>

iterate >lib<

ext2fs read inode 46921

ext2fs read 23 group descriptor (blkno 2 blkoff 736)

<5, 224, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 188419 blkoff 0

<376838, 0, 128>

<DIR> 3072 lib

ext2fs_read_block 00000205

<1034, 92, 8>

ext2fs_read_block 00000205

<1034, 100, 4>

iterate >root<

ext2fs read inode 6121

ext2fs read 3 group descriptor (blkno 2 blkoff 96)

<4, 96, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 24838 blkoff 0

<49676, 0, 128>

<DIR> 1024 root

ext2fs_read_block 00000205

<1034, 104, 8>

ext2fs_read_block 00000205

<1034, 112, 3>

iterate >dev<

ext2fs read inode 22441

ext2fs read 11 group descriptor (blkno 2 blkoff 352)

<4, 352, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 90115 blkoff 0

<180230, 0, 128>

<DIR> 1024 dev

ext2fs_read_block 00000205

<1034, 116, 8>

ext2fs_read_block 00000205

<1034, 124, 4>

iterate >sbin<

ext2fs read inode 8161

ext2fs read 4 group descriptor (blkno 2 blkoff 128)

<4, 128, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 32771 blkoff 0

<65542, 0, 128>

<DIR> 1024 sbin

ext2fs_read_block 00000205

<1034, 128, 8>

ext2fs_read_block 00000205

<1034, 136, 3>

iterate >usr<

ext2fs read inode 73441

ext2fs read 36 group descriptor (blkno 3 blkoff 128)

<6, 128, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 294915 blkoff 0

<589830, 0, 128>

<DIR> 1024 usr

ext2fs_read_block 00000205

<1034, 140, 8>

ext2fs_read_block 00000205

<1034, 148, 4>

iterate >proc<

ext2fs read inode 38761

ext2fs read 19 group descriptor (blkno 2 blkoff 608)

<5, 96, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 155651 blkoff 0

<311302, 0, 128>

<DIR> 1024 proc

ext2fs_read_block 00000205

<1034, 152, 8>

ext2fs_read_block 00000205

<1034, 160, 3>

iterate >opt<

ext2fs read inode 42841

ext2fs read 21 group descriptor (blkno 2 blkoff 672)

<5, 160, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 172035 blkoff 0

<344070, 0, 128>

<DIR> 1024 opt

ext2fs_read_block 00000205

<1034, 164, 8>

ext2fs_read_block 00000205

<1034, 172, 7>

iterate >linuxrc<

ext2fs read inode 10898

ext2fs read 5 group descriptor (blkno 2 blkoff 160)

<4, 160, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 41309 blkoff 128

<82618, 128, 128>

<SYM> 11 linuxrc

ext2fs_read_block 00000205

<1034, 180, 8>

ext2fs_read_block 00000205

<1034, 188, 3>

iterate >run<

ext2fs read inode 51001

ext2fs read 25 group descriptor (blkno 2 blkoff 800)

<5, 288, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 205062 blkoff 0

<410124, 0, 128>

<DIR> 1024 run

ext2fs_read_block 00000205

<1034, 192, 8>

ext2fs_read_block 00000205

<1034, 200, 6>

iterate >config<

ext2fs read inode 53041

ext2fs read 26 group descriptor (blkno 2 blkoff 832)

<5, 320, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 212995 blkoff 0

<425990, 0, 128>

<DIR> 1024 config

ext2fs_read_block 00000205

<1034, 208, 8>

ext2fs_read_block 00000205

<1034, 216, 3>

iterate >var<

ext2fs read inode 55081

ext2fs read 27 group descriptor (blkno 2 blkoff 864)

<5, 352, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 221446 blkoff 0

<442892, 0, 128>

<DIR> 1024 var

ext2fs_read_block 00000205

<1034, 220, 8>

ext2fs_read_block 00000205

<1034, 228, 3>

iterate >tmp<

ext2fs read inode 30601

ext2fs read 15 group descriptor (blkno 2 blkoff 480)

<4, 480, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 122883 blkoff 0

<245766, 0, 128>

<DIR> 1024 tmp

ext2fs_read_block 00000205

<1034, 232, 8>

ext2fs_read_block 00000205

<1034, 240, 3>

iterate >bin<

ext2fs read inode 44881

ext2fs read 22 group descriptor (blkno 2 blkoff 704)

<5, 192, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 180227 blkoff 0

<360454, 0, 128>

<DIR> 3072 bin

ext2fs_read_block 00000205

<1034, 244, 8>

ext2fs_read_block 00000205

<1034, 252, 3>

iterate >sys<

ext2fs read inode 57121

ext2fs read 28 group descriptor (blkno 2 blkoff 896)

<5, 384, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 229379 blkoff 0

<458758, 0, 128>

<DIR> 1024 sys

*******************Execute Primary Image ***********

mmc3(part 0) is current device

MMC read: dev # 3, block # 40960, count 8192 ... 8192 blocks read: OK

* kernel: default image load address = 0x10800000

## Booting kernel from Legacy Image at 10800000 ...

****CV1 Kernel Validation Based on CRC Algorithm***

Image Name: Linux-3.0.35-ts-armv7l

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 3379356 Bytes = 3.2 MB

Load Address: 10008000

Entry Point: 10008000

Verifying Checksum ... OK

********Image validated********

kernel data at 0x10800040, len = 0x0033909c (3379356)

## No init Ramdisk

ramdisk start = 0x00000000, ramdisk end = 0x00000000

Loading Kernel Image ... OK

OK

kernel loaded at 0x10008000, end = 0x1034109c

## Transferring control to Linux (at address 10008000) ...

Starting kernel ...

At this point the boot loader screen disappears and the Lcd screen is blank for 18 seconds.

Linux version 3.0.35-ts-armv7l (user@NTP-096) (gcc version 4.8.2 (Timesys 20140527) ) #1 SMP PREEMPT Fri Jan 2 13:14:44 IST 2015

CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d

CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache

Machine: XXXX YYYY device Target Board

Ignoring unrecognised tag 0x54410008

Memory policy: ECC disabled, Data cache writealloc

CPU identified as i.MX6Q, silicon rev 1.2

PERCPU: Embedded 7 pages/cpu @8c008000 s5440 r8192 d15040 u32768

Built 1 zonelists in Zone order, mobility grouping on. Total pages: 194560

Kernel command line: setenv bootargs ${bootargs} console=ttymxc1,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=adv739x,BT656-NTSC,if=BT656,fbpix=RGB565 video=mxcfb1:dev=hdmi,1280x720M@60,if=RGB24 video=mxcfb2:dev=ldb,LDB-XGA,if=RGB24,bpp=24,fbpix=BGR32 ldb=dul0 video=mxcfb3:off consoleblank=0

PID hash table entries: 4096 (order: 2, 16384 bytes)

Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

Memory: 512MB 256MB = 768MB total

Memory: 766668k/766668k available, 281908k reserved, 0K highmem

Virtual kernel memory layout:

vector : 0xffff0000 - 0xffff1000 ( 4 kB)

fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

DMA : 0xf4600000 - 0xffe00000 ( 184 MB)

vmalloc : 0xc0800000 - 0xf2000000 ( 792 MB)

lowmem : 0x80000000 - 0xc0000000 (1024 MB)

pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)

modules : 0x7f000000 - 0x7fe00000 ( 14 MB)

.init : 0x80008000 - 0x8003a000 ( 200 kB)

.text : 0x8003a000 - 0x809be838 (9747 kB)

.data : 0x809c0000 - 0x80a17360 ( 349 kB)

.bss : 0x80a17384 - 0x80a5fe18 ( 291 kB)

SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1

Preemptible hierarchical RCU implementation.

NR_IRQS:624

MXC GPIO hardware

sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms

arm_max_freq=800MHz

MXC_Early serial console at MMIO 0x21e8000 (options '115200')

bootconsole [ttymxc1] enabled

Console: colour dummy device 80x30

Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available

CPU1: Booted secondary processor

CPU2: Booted secondary processor

CPU3: Booted secondary processor

Brought up 4 CPUs

SMP: Total of 4 processors activated (6324.22 BogoMIPS).

print_constraints: dummy:

NET: Registered protocol family 16

print_constraints: vddpu: 725 <--> 1300 mV at 700 mV fast normal

print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal

print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal

print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal

print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal

print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal

hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.

hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.

hw-breakpoint: maximum watchpoint size is 4 bytes.

L310 cache controller enabled

l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x02070000, Cache size: 1048576 B

CV1 *** mxc_pwm_probe

CV1 *** Got pwm for PWM for IR Board\n

bio: create slab <bio-0> at 0

mxs-dma mxs-dma-apbh: initialized

print_constraints: vmmc: 3300 mV

SCSI subsystem initialized

spi_imx imx6q-ecspi.0: probed

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

Freescale USB OTG Driver loaded, $Revision: 1.55 $

mc_pfuze 1-0008: recv failed!:-110,c8

mc_pfuze: probe of 1-0008 failed with error -1

imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)

imx-ipuv3 imx-ipuv3.1: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)

MIPI CSI2 driver module loaded

Advanced Linux Sound Architecture Driver Version 1.0.24.

Bluetooth: Core ver 2.16

NET: Registered protocol family 31

Bluetooth: HCI device and connection manager initialized

Bluetooth: HCI socket layer initialized

Bluetooth: L2CAP socket layer initialized

Bluetooth: SCO socket layer initialized

i2c-core: driver [max17135] using legacy suspend method

i2c-core: driver [max17135] using legacy resume method

Switching to clocksource mxc_timer1

NET: Registered protocol family 2

IP route cache hash table entries: 32768 (order: 5, 131072 bytes)

TCP established hash table entries: 131072 (order: 8, 1048576 bytes)

TCP bind hash table entries: 65536 (order: 7, 786432 bytes)

TCP: Hash tables configured (established 131072 bind 65536)

TCP reno registered

UDP hash table entries: 512 (order: 2, 16384 bytes)

UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)

NET: Registered protocol family 1

RPC: Registered named UNIX socket transport module.

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

RPC: Registered tcp NFSv4.1 backchannel transport module.

PMU: registered new PMU device of type 0

Static Power Management for Freescale i.MX6

wait mode is enabled for i.MX6

cpaddr = c0880000 suspend_iram_base=c08f8000

PM driver module loaded

IMX usb wakeup probe

add wake up source irq 75

IMX usb wakeup probe

cpu regulator mode:ldo_enable

i.MXC CPU frequency driver

alg: No test for stdrng (krng)

io scheduler noop registered

io scheduler deadline registered

io scheduler cfq registered (default)

###mxc_adv739x_i2c_init #1

###mxc_adv739x_probe #1

MIPI DSI driver module loaded

mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver adv739x

mxc_adv739x_setmode #1

Console: switching to colour frame buffer device 90x30

mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver hdmi

mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1

fbcvt: 1280x720@60: CVT Name - .921M9

mxc_sdc_fb mxc_sdc_fb.2: register mxc display driver ldb

_regulator_get: get() with no identifier

mxc_sdc_fb mxc_sdc_fb.3: Can't get fb option for mxcfb3!

imx-sdma imx-sdma: loaded firmware 1.1

imx-sdma imx-sdma: initialized

Serial: IMX driver

imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX

console [ttymxc1] enabled, bootconsole disabled

imx-uart.2: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX

imx-uart.3: ttymxc3 at MMIO 0x21f0000 (irq = 61) is a IMX

Can't recover from RESET HBA!

No sata disk.

FEC Ethernet Driver

fec_enet_mii_bus: probed

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller

fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1

fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000

fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

add wake up source irq 72

fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller

fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2

fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200

fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 1 port detected

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

ARC USBOTG Device Controller driver (1 August 2005)

mousedev: PS/2 mouse device common for all mice

i2c-core: driver [isl29023] using legacy suspend method

i2c-core: driver [isl29023] using legacy resume method

snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0

i2c /dev entries driver

max8903-charger max8903-charger.1: Invalid pin: chg.

max8903-charger: probe of max8903-charger.1 failed with error -22

imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0)

Bluetooth: Virtual HCI driver ver 1.3

Bluetooth: HCI UART driver ver 2.2

Bluetooth: HCIATH3K protocol initialized

Bluetooth: Generic Bluetooth USB driver ver 0.6

usbcore: registered new interface driver btusb

sdhci: Secure Digital Host Controller Interface driver

mxc_hdmi mxc_hdmi: Read EDID again

sdhci: Copyright(c) Pierre Ossman

mmc0: SDHCI controller on platform [sdhci-esdhc-imx.3] using DMA

sdhci sdhci-esdhc-imx.0: no write-protect pin available!

mmc1: no vmmc regulator found

mmc1: SDHCI controller on platform [sdhci-esdhc-imx.0] using DMA

mmc2: SDHCI controller on platform [sdhci-esdhc-imx.1] using DMA

mmc3: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA

mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed

VPU initialized

mxc_asrc registered

Galcore version 4.6.9.6622

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

usbcore: registered new interface driver snd-usb-audio

mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio

Cirrus Logic CS42888 ALSA SoC Codec Driver

i2c-core: driver [cs42888] using legacy suspend method

i2c-core: driver [cs42888] using legacy resume method

imx_3stack asoc driver

asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok

ALSA device list:

#0: imx-hdmi-soc

NET: Registered protocol family 26

mmc0: new high speed DDR MMC card at address 0001

mmcblk0: mmc0:0001 MMC04G 3.52 GiB

mmcblk0boot0: mmc0:0001 MMC04G partition 1 16.0 MiB

mmcblk0boot1: mmc0:0001 MMC04G partition 2 16.0 MiB

mmcblk0: p1 p2 p3 p4

TCP cubic registered

mmcblk0boot1: unknown partition table

NET: Registered protocol family 17

mmcblk0boot0: unknown partition table

Bluetooth: RFCOMM TTY layer initialized

Bluetooth: RFCOMM socket layer initialized

Bluetooth: RFCOMM ver 1.11

Bluetooth: BNEP (Ethernet Emulation) ver 1.3

Bluetooth: BNEP filters: protocol multicast

Bluetooth: HIDP (Human Interface Emulation) ver 1.2

lib80211: common routines for IEEE802.11 drivers

VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4

Bus freq driver module loaded

Bus freq driver Enabled

mxc_dvfs_core_probe

DVFS driver module loaded

snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:00:11 UTC (11)

EXT3-fs: barriers not enabled

kjournald starting. Commit interval 5 seconds

EXT3-fs (mmcblk0p1): using internal journal

EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode

VFS: Mounted root (ext3 filesystem) on device 179:1.

Freeing init memory: 200K

init started: BusyBox v1.20.2 (2014-07-11 16:18:48 IST)

mxc_hdmi mxc_hdmi: No modes read from edid

mxc_hdmi mxc_hdmi: create default modelist

fbcvt: 1280x720@60: CVT Name - .921M9

mmc2: queuing unknown CIS tuple 0x01 (3 bytes)

mmc2: queuing unknown CIS tuple 0x1a (5 bytes)

mmc2: queuing unknown CIS tuple 0x1b (8 bytes)

mmc2: queuing unknown CIS tuple 0x14 (0 bytes)

mmc2: queuing unknown CIS tuple 0x80 (1 bytes)

mmc2: queuing unknown CIS tuple 0x81 (1 bytes)

mmc2: queuing unknown CIS tuple 0x82 (1 bytes)

mmc2: new high speed SDIO card at address 0001

mmc3: queuing unknown CIS tuple 0x01 (3 bytes)

mmc3: queuing unknown CIS tuple 0x1a (5 bytes)

mmc3: queuing unknown CIS tuple 0x1b (8 bytes)

mmc3: queuing unknown CIS tuple 0x14 (0 bytes)

mmc3: queuing unknown CIS tuple 0x80 (1 bytes)

mmc3: queuing unknown CIS tuple 0x81 (1 bytes)

mmc3: queuing unknown CIS tuple 0x82 (1 bytes)

mmc3: new high speed SDIO card at address 0001

Setting hotplug handler: [ OK ]

Creating device files: Auto-mount of [/media/mmcblk0p1] successful

EXT3-fs: barriers not enabled

kjournald starting. Commit interval 5 seconds

EXT3-fs (mmcblk0p2): using internal journal

EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode

Auto-mount of [/media/mmcblk0p2] successful

EXT3-fs: barriers not enabled

kjournald starting. Commit interval 5 seconds

EXT3-fs (mmcblk0p3): using internal journal

EXT3-fs (mmcblk0p3): mounted filesystem with writeback data mode

Auto-mount of [/media/mmcblk0p3] successful

EXT3-fs: barriers not enabled

kjournald starting. Commit interval 5 seconds

EXT3-fs (mmcblk0p4): using internal journal

EXT3-fs (mmcblk0p4): mounted filesystem with writeback data mode

Auto-mount of [/media/mmcblk0p4] successful

[ OK ]

modprobe: module galcore not found in modules.dep

Setting timezone and system clock: hwclock: settimeofday: Invalid argument

[Fail]

Starting system logging.

Configuring network interfaces: ifdown: interface lo not configured

done

Starting dbus: [ OK ]

Starting ntpd: [OK]

****Executing Custom Script************ CV1: /dev/mmcblk1p1$ Not Mounted ****

48

Error count=0****Startup Error logged:19700101, 5:30:22.000, 30

****gadgetfs: USB Gadget filesystem, version 24 Aug 2004

AR6k module loading start...

Module Arguments...

Platform set to LOCAL_i686-SDIO

Platform Setup Script is: /home/plat_LOCAL_i686-SDIO.sh

Image path: /home

Mac address:

sdiostack loading

loading AR6K module... Args = (bmienable=1 ifname=wlan0 busspeedlow=0) , logfile:/tmp/dbglog.out

AR6000: configuration opcode 7 is only used for RTOS systems, not Linux systemsCompleted loading the module ar6000_avail_ev

BMI Write Register (address: 0x1c284, param: 0xf9104001)

BMI Write Register (address: 0x4020, param: 0x1)

BMI Write Register (address: 0x1404c, param: 0x28)

BMI Write Register (address: 0x14050, param: 0x20)

BMI Write Register (address: 0x14054, param: 0x20)

BMI Write Register (address: 0x14058, param: 0x20)

BMI Write Register (address: 0x1405c, param: 0x20)

BMI Write Register (address: 0x40e0, param: 0x100000)

Load Board Data from /home/ath6k/AR6003/hw2.1.1/fakeBoardData_AR6003_v2_0.bin

BMI Write Memory (address: 0x1234, filename: /home/ath6k/AR6003/hw2.1.1/otp.bin)

BMI Execute (address: 0x945d20, param: 0x0)

Return Value from target: 0x0

BMI Write Memory (address: 0x1234, filename: /home/ath6k/AR6003/hw2.1.1/athwlan.bin)

BMI Write Memory (address: 0x57fec8, filename: /home/ath6k/AR6003/hw2.1.1/data.patch.hw3_0.bin)

BMI Write Memory (address: 0x540618, value: 0x57fec8)

BMI Write Register (address: 0x5406a4, param: 0x16)

BMI Write Register (address: 0x540680, param: 0x8)

BMI Done

AR6K: ** HIF layer does not support scatter requests (17)

Auto-mount of [/media/mmcblk0p1] successful

EXT3-fs: barriers not enabled

kjournald starting. Commit interval 5 seconds

EXT3-fs (mmcblk0p2): using internal journal

EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode

Auto-mount of [/media/mmcblk0p2] successful

EXT3-fs: barriers not enabled

kjournald starting. Commit interval 5 seconds

EXT3-fs (mmcblk0p3): using internal journal

EXT3-fs (mmcblk0p3): mounted filesystem with writeback data mode

Auto-mount of [/media/mmcblk0p3] successful

EXT3-fs: barriers not enabled

kjournald starting. Commit interval 5 seconds

EXT3-fs (mmcblk0p4): using internal journal

EXT3-fs (mmcblk0p4): mounted filesystem with writeback data mode

Auto-mount of [/media/mmcblk0p4] successful

[ OK ]

modprobe: module galcore not found in modules.dep

Setting timezone and system clock: hwclock: settimeofday: Invalid argument

[Fail]

Starting system logging.

Configuring network interfaces: ifdown: interface lo not configured

done

Starting dbus: [ OK ]

Starting ntpd: [OK]

****Executing Custom Script************ CV1: /dev/mmcblk1p1$ Not Mounted ****

48

Error count=0****Startup Error logged:19700101, 5:30:22.000, 30

****gadgetfs: USB Gadget filesystem, version 24 Aug 2004

AR6k module loading start...

Module Arguments...

Platform set to LOCAL_i686-SDIO

Platform Setup Script is: /home/plat_LOCAL_i686-SDIO.sh

Image path: /home

Mac address:

sdiostack loading

loading AR6K module... Args = (bmienable=1 ifname=wlan0 busspeedlow=0) , logfile:/tmp/dbglog.out

AR6000: configuration opcode 7 is only used for RTOS systems, not Linux systemsCompleted loading the module ar6000_avail_ev

BMI Write Register (address: 0x1c284, param: 0xf9104001)

BMI Write Register (address: 0x4020, param: 0x1)

BMI Write Register (address: 0x1404c, param: 0x28)

BMI Write Register (address: 0x14050, param: 0x20)

BMI Write Register (address: 0x14054, param: 0x20)

BMI Write Register (address: 0x14058, param: 0x20)

BMI Write Register (address: 0x1405c, param: 0x20)

BMI Write Register (address: 0x40e0, param: 0x100000)

Load Board Data from /home/ath6k/AR6003/hw2.1.1/fakeBoardData_AR6003_v2_0.bin

BMI Write Memory (address: 0x1234, filename: /home/ath6k/AR6003/hw2.1.1/otp.bin)

BMI Execute (address: 0x945d20, param: 0x0)

Return Value from target: 0x0

BMI Write Memory (address: 0x1234, filename: /home/ath6k/AR6003/hw2.1.1/athwlan.bin)

BMI Write Memory (address: 0x57fec8, filename: /home/ath6k/AR6003/hw2.1.1/data.patch.hw3_0.bin)

BMI Write Memory (address: 0x540618, value: 0x57fec8)

BMI Write Register (address: 0x5406a4, param: 0x16)

BMI Write Register (address: 0x540680, param: 0x8)

BMI Done

AR6K: ** HIF layer does not support scatter requests (17)

AR6K: targetconf_ver : 1

Platform set to LOCAL_i686-SDIO

Platform Setup Script is: /home/plat_LOCAL_i686-SDIO.sh

Image path: /home

Mac address:

sdiostack loading

loading AR6K module... Args = (bmienable=1 ifname=uap0 busspeedlow=0) , logfile:/tmp/dbglog.out

BMI Write Register (address: 0x1c284, param: 0xf9104001)

BMI Write Register (address: 0x4020, param: 0x1)

BMI Write Register (address: 0x1404c, param: 0x28)

BMI Write Register (address: 0x14050, param: 0x20)

BMI Write Register (address: 0x14054, param: 0x20)

BMI Write Register (address: 0x14058, param: 0x20)

BMI Write Register (address: 0x1405c, param: 0x20)

BMI Write Register (address: 0x40e0, param: 0x100000)

Load Board Data from /home/ath6k/AR6003/hw2.1.1/fakeBoardData_AR6003_v2_0.bin

BMI Write Memory (address: 0x1234, filename: /home/ath6k/AR6003/hw2.1.1/otp.bin)

BMI Execute (address: 0x945d20, param: 0x0)

Return Value from target: 0x0

BMI Write Memory (address: 0x1234, filename: /home/ath6k/AR6003/hw2.1.1/athwlan_router.bin)

BMI Write Memory (address: 0x57fec8, filename: /home/ath6k/AR6003/hw2.1.1/data.patch.hw3_0.bin)

BMI Write Memory (address: 0x540618, value: 0x57fec8)

BMI Write Register (address: 0x5406a4, param: 0x16)

BMI Write Register (address: 0x540680, param: 0x8)

BMI Done

AR6K: ** HIF layer does not support scatter requests (17)

AR6K: targetconf_ver : 1

AR6k module load Done...

/etc/init.d/S50-openssh: Creating system user 'sshd' with generic settings. Review and modify as required.

Generating public/private rsa1 key pair.

killall: hostapd: no process killed

killall: udhcpd: no process killed

info, udhcpd (v0.9.9-pre) started

error, max_leases value (234) not sane, setting to 9 instead

Configuration file: /home/hostapd.conf

killall: udhcpc,: no process killed

killall: wpa_supplicant: no process killed

Internet Systems Consortium DHCP Client V3.1-ESV-R3

For info, please visit https://www.isc.org/software/dhcp/

channel hint set to 2412

ioctl[SIOCGIWESSID]: Invalid argument

Using interface uap0 with hwaddr 00:80:92:62:25:ec and ssid 'UltraGen2_AP'

WPA: Nonce1 - hexdump(len=24): [NULL]

Listening on LPF/eth0/00:10:2e:e0:00:02

Sending on LPF/eth0/00:10:2e:e0:00:02

Sending on Socket/fallback

Internet Systems Consortium DHCP Client V3.1-ESV-R3

For info, please visit https://www.isc.org/software/dhcp/

eth0: Freescale FEC PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=1:01, irq=-1)

0x100019, Log file create

0x100095, ErrLogger_appndr_dbg_file_open()

QIconvCodec::convertFromUnicode: using Latin-1 for conversion, iconv_open failed

wlan0: Trying to associate with SSID 'Hospital_AP'

httpd not running, trying to start

0x100019, Log file create

0x100095, ErrLogger_appndr_dbg_file_open()

gadgetfs: bound to fsl-usb2-udc driver

Suspend udc for OTG auto detect

fsl-usb2-udc: bind to driver gadgetfs

gadgetfs: suspended from state 2

/dev/gadget/fsl-usb2-udc ep1 configured

serial="o27dg4f58lqonneusbky1kaya77f3lua1vyqiojae05tf9nukjdrz1uq0x58e2u"

0x100019, Log file create

0x100095, ErrLogger_appndr_dbg_file_open()

Listening on LPF/eth0/00:10:2e:e0:00:02

Sending on LPF/eth0/00:10:2e:e0:00:02

Sending on Socket/fallback

gadgetfs: connected

gadgetfs: disconnected

gadgetfs: connected

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5

Your identification has been saved in /etc/openssh/ssh_host_key.

Your public key has been saved in /etc/openssh/ssh_host_key.pub.

The key fingerprint is:

26:0c:cd:34:a4:b2:c1:90:0d:8a:71:c3:78:76:4e:0f root@SABRE_SDB

The key's randomart image is:

+--[RSA1 2048]----+

|+*o .+ |

|===.E= . |

|oo++ooo |

| +.o. |

| . o S |

| o |

| |

+-----------------+

Generating public/private dsa key pair.

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

Your identification has been saved in /etc/openssh/ssh_host_dsa_key.

Your public key has been saved in /etc/openssh/ssh_host_dsa_key.pub.

The key fingerprint is:

b5:94:ed:5e:83:f9:1d:6c:db:84:12:0e:dd:04:ed:cc root@SABRE_SDB

The key's randomart image is:

+--[ DSA 1024]----+

| .o. |

| + o. |

| = ++. |

| o = +E. |

| S . * ++.|

| . +.++|

| . ..o|

| |

+-----------------+

Generating public/private rsa key pair.

wlan0: Trying to associate with SSID 'Hospital_AP'

Your identification has been saved in /etc/openssh/ssh_host_rsa_key.

Your public key has been saved in /etc/openssh/ssh_host_rsa_key.pub.

The key fingerprint is:

5a:6a:fe:0b:6b:bd:54:45:f7:e6:0a:87:6a:65:e2:eb root@SABRE_SDB

The key's randomart image is:

+--[ RSA 2048]----+

| . . |

| . . . |

| . o|

| . . o |

| S o = . .|

| + o = o . |

| =.. + . |

| o.+.. . |

| .o.++E |

+-----------------+

Generating public/private ecdsa key pair.

Your identification has been saved in /etc/openssh/ssh_host_ecdsa_key.

Your public key has been saved in /etc/openssh/ssh_host_ecdsa_key.pub.

The key fingerprint is:

cb:5d:a0:39:85:44:33:d3:bd:7a:32:65:5f:91:7e:2d root@SABRE_SDB

The key's randomart image is:

+--[ECDSA 256]---+

| .*. . .|

| . =. . o |

| . o .. o|

| + .+ E.+|

| S +.. o.|

| . ++.. . |

| o .+ |

| |

+-----------------+

Starting /usr/sbin/sshd: Could not load host key: /etc/openssh/ssh_host_ed25519_key

[ OK ]

/etc/init.d/S64-apache-httpd: Creating system user 'daemon' with generic settings. Review and modify as required.

Starting apache-httpd

httpd (pid 2566) already running

BusyBox v1.20.2 (2014-07-11 16:18:48 IST) built-in shell (ash)

Enter 'help' for a list of built-in commands.

# DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3

No DHCPOFFERS received.

No working leases in persistent database - sleeping.

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

wlan0: CTRL-EVENT-DISCONNECTED bssid=00:00:00:00:00:00 reason=0

wlan0: Trying to associate with SSID 'Hospital_AP'

ÿ

U-Boot 2009.08 (May 15 2014 - 09:19:57)

CPU: Freescale i.MX6 family TO1.2 at 792 MHz

Thermal sensor with ratio = 173

Temperature: 27 C, calibration data 0x5484c469

mx6q pll1: 792MHz

mx6q pll2: 528MHz

mx6q pll3: 480MHz

mx6q pll8: 50MHz

ipg clock : 66000000Hz

ipg per clock : 66000000Hz

uart clock : 80000000Hz

cspi clock : 60000000Hz

ahb clock : 132000000Hz

axi clock : 264000000Hz

emi_slow clock: 132000000Hz

ddr clock : 528000000Hz

usdhc1 clock : 198000000Hz

usdhc2 clock : 198000000Hz

usdhc3 clock : 198000000Hz

usdhc4 clock : 198000000Hz

nfc clock : 24000000Hz

Board: i.MX6Q-SABRESD: unknown-board Board: 0x63012 [POR ]

Boot Device: MMC

DRAM: 1 GB

MMC: FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2,FSL_USDHC: 3

Using default environment

In: serial

Out: serial

Err: serial

Net: got MAC address from IIM: 00:10:2e:e0:00:02

FEC0 [PRIME]

Hit any key to stop autoboot: 0

## Booting kernel from Legacy Image at 10800000 ...

Image Name: Linux-3.0.35-ts-armv7l

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 3170380 Bytes = 3 MB

Load Address: 10008000

Entry Point: 10008000

Verifying Checksum ... OK

## Loading init Ramdisk from Legacy Image at 10c00000 ...

Image Name: uboot initramfs rootfs

Image Type: ARM Linux RAMDisk Image (gzip compressed)

Data Size: 4545326 Bytes = 4.3 MB

Load Address: 00000000

Entry Point: 00000000

Verifying Checksum ... OK

Loading Kernel Image ... OK

OK

Starting kernel ...

Linux version 3.0.35-ts-armv7l (sfm@sfm) (gcc version 4.8.2 (Timesys 20140527) ) #1 SMP PREEMPT Wed Aug 27 14:25:16 IST 2014

CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d

CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache

Machine: XXXX YYYY device Target Board

Memory policy: ECC disabled, Data cache writealloc

CPU identified as i.MX6Q, silicon rev 1.2

PERCPU: Embedded 7 pages/cpu @8c008000 s5184 r8192 d15296 u32768

Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227328

Kernel command line: console=ttymxc1,115200 rdinit=/linuxrc enable_wait_mode=off

PID hash table entries: 4096 (order: 2, 16384 bytes)

Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

Memory: 640MB 256MB = 896MB total

Memory: 897220k/897220k available, 151356k reserved, 0K highmem

Virtual kernel memory layout:

vector : 0xffff0000 - 0xffff1000 ( 4 kB)

fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

DMA : 0xf4600000 - 0xffe00000 ( 184 MB)

vmalloc : 0xc0800000 - 0xf2000000 ( 792 MB)

lowmem : 0x80000000 - 0xc0000000 (1024 MB)

pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)

modules : 0x7f000000 - 0x7fe00000 ( 14 MB)

.init : 0x80008000 - 0x80097000 ( 572 kB)

.text : 0x80097000 - 0x80610598 (5606 kB)

.data : 0x80612000 - 0x806602e0 ( 313 kB)

.bss : 0x80660304 - 0x8068b254 ( 172 kB)

SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1

Preemptible hierarchical RCU implementation.

NR_IRQS:624

MXC GPIO hardware

sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms

arm_max_freq=800MHz

MXC_Early serial console at MMIO 0x21e8000 (options '115200')

bootconsole [ttymxc1] enabled

Console: colour dummy device 80x30

Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available

CPU1: Booted secondary processor

CPU2: Booted secondary processor

CPU3: Booted secondary processor

Brought up 4 CPUs

SMP: Total of 4 processors activated (6324.22 BogoMIPS).

print_constraints: dummy:

NET: Registered protocol family 16

print_constraints: vddpu: 725 <--> 1300 mV at 700 mV fast normal

print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal

print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal

print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal

print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal

print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal

No AHCI save PWR: PDDQ disabled

hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.

hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.

hw-breakpoint: maximum watchpoint size is 4 bytes.

L310 cache controller enabled

l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x02070000, Cache size: 1048576 B

CV1 *** mxc_pwm_probe

CV1 *** Got pwm for PWM for IR Board\n

bio: create slab <bio-0> at 0

mxs-dma mxs-dma-apbh: initialized

print_constraints: vmmc: 3300 mV

SCSI subsystem initialized

spi_imx imx6q-ecspi.0: probed

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

mc_pfuze 1-0008: recv failed!:-110,c8

mc_pfuze: probe of 1-0008 failed with error -1

imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)

imx-ipuv3 imx-ipuv3.1: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)

Advanced Linux Sound Architecture Driver Version 1.0.24.

Bluetooth: Core ver 2.16

NET: Registered protocol family 31

Bluetooth: HCI device and connection manager initialized

Bluetooth: HCI socket layer initialized

Bluetooth: L2CAP socket layer initialized

Bluetooth: SCO socket layer initialized

i2c-core: driver [max17135] using legacy suspend method

i2c-core: driver [max17135] using legacy resume method

Switching to clocksource mxc_timer1

Clockevents: could not switch to one-shot mode:

Clockevents: could not switch to one-shot mode: dummy_timer is not functional.

dummy_timer is not functional.

Clockevents: could not switch to one-shot mode:

Could not switch to high resolution mode on CPU 3

dummy_timer is not functional.

Could not switch to high resolution mode on CPU 1

Could not switch to high resolution mode on CPU 0

NET: Registered protocol family 2

IP route cache hash table entries: 32768 (order: 5, 131072 bytes)

TCP established hash table entries: 131072 (order: 8, 1048576 bytes)

TCP bind hash table entries: 65536 (order: 7, 786432 bytes)

TCP: Hash tables configured (established 131072 bind 65536)

TCP reno registered

UDP hash table entries: 512 (order: 2, 16384 bytes)

UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)

NET: Registered protocol family 1

RPC: Registered named UNIX socket transport module.

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

RPC: Registered tcp NFSv4.1 backchannel transport module.

Unpacking initramfs...

dummy_timer is not functional.

Could not switch to high resolution mode on CPU 2

Freeing initrd memory: 4436K

PMU: registered new PMU device of type 0

Static Power Management for Freescale i.MX6

wait mode is disabled for i.MX6

cpaddr = c0880000 suspend_iram_base=c08f8000

PM driver module loaded

IMX usb wakeup probe

cpu regulator mode:ldo_enable

i.MXC CPU frequency driver

msgmni has been set to 1761

cryptodev: driver loaded.

io scheduler noop registered

io scheduler deadline registered

io scheduler cfq registered (default)

mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver adv739x

mxc_sdc_fb mxc_sdc_fb.0: NO mxc display driver found!

mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver hdmi

mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1

fbcvt: 1920x1080@60: CVT Name - 2.073M9

Console: switching to colour frame buffer device 240x67

mxc_sdc_fb mxc_sdc_fb.2: register mxc display driver ldb

_regulator_get: get() with no identifier

mxc_sdc_fb mxc_sdc_fb.3: register mxc display driver ldb

imx-sdma imx-sdma: loaded firmware 1.1

imx-sdma imx-sdma: initialized

mxc_hdmi mxc_hdmi: Read EDID again

mxc_hdmi mxc_hdmi: No modes read from edid

mxc_hdmi mxc_hdmi: create default modelist

fbcvt: 1920x1080@60: CVT Name - 2.073M9

Serial: IMX driver

imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX

console [ttymxc1] enabled, bootconsole disabled

imx-uart.2: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX

imx-uart.3: ttymxc3 at MMIO 0x21f0000 (irq = 61) is a IMX

loop: module loaded

m25p80 spi0.0: found m25p05-nonjedec, expected sst25vf016b

m25p80 spi0.0: m25p05-nonjedec (64 Kbytes)

Creating 2 MTD partitions on "m25p80":

0x000000000000-0x000000100000 : "bootloader"

mtd: partition "bootloader" extends beyond the end of device "m25p80" -- size truncated to 0x10000

0x000000010000-0x000000010000 : "kernel"

mtd: partition "kernel" is out of reach -- disabled

GPMI NAND driver registered. (IMX)

vcan: Virtual CAN interface driver

FEC Ethernet Driver

fec_enet_mii_bus: probed

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

ARC USBOTG Device Controller driver (1 August 2005)

add wake up source irq 75

g_file_storage gadget: controller 'fsl-usb2-udc' not recognized

check_parameters:UTP settings are in place now, overriding defaults

g_file_storage gadget: No serial-number string provided!

g_file_storage gadget: File-backed Storage Gadget, version: 1 September 2010

g_file_storage gadget: Number of LUNs=1

fsl-usb2-udc: bind to driver g_file_storage

mousedev: PS/2 mouse device common for all mice

egalax_ts 1-0004: egalax_ts: failed to read firmware version

egalax_ts: probe of 1-0004 failed with error -5

snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0

i2c /dev entries driver

Linux video capture interface: v2.00

mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16

mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17

mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18

mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video19

mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video20

imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)

Bluetooth: Virtual HCI driver ver 1.3

Bluetooth: Generic Bluetooth USB driver ver 0.6

usbcore: registered new interface driver btusb

sdhci: Secure Digital Host Controller Interface driver

sdhci: Copyright(c) Pierre Ossman

mmc0: SDHCI controller on platform [sdhci-esdhc-imx.3] using DMA

sdhci sdhci-esdhc-imx.0: no write-protect pin available!

mmc1: no vmmc regulator found

mmc1: SDHCI controller on platform [sdhci-esdhc-imx.0] using DMA

mmc2: SDHCI controller on platform [sdhci-esdhc-imx.1] using DMA

mmc3: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA

mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed

VPU initialized

mxc_asrc registered

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

Cirrus Logic CS42888 ALSA SoC Codec Driver

i2c-core: driver [cs42888] using legacy suspend method

i2c-core: driver [cs42888] using legacy resume method

imx_3stack asoc driver

ALSA device list:

No soundcards found.

TCP cubic registered

NET: Registered protocol family 17

can: controller area network core (rev 20090105 abi 8)

NET: Registered protocol family 29

can: raw protocol (rev 20090105)

can: broadcast manager protocol (rev 20090105 t)

Bluetooth: RFCOMM TTY layer initialized

Bluetooth: RFCOMM socket layer initialized

Bluetooth: RFCOMM ver 1.11

Bluetooth: BNEP (Ethernet Emulation) ver 1.3

Bluetooth: BNEP filters: protocol multicast

Bluetooth: HIDP (Human Interface Emulation) ver 1.2

VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4

Bus freq driver module loaded

Bus freq driver Enabled

mxc_dvfs_core_probe

DVFS driver module loaded

snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0)

Freeing init memory: 572K

Starting UTP

ln: /etc/mtab: File exists

disable turn off display

Starting the hotplug events dispatcher udevd

udevd (1988): /proc/1988/oom_adj is deprecated, please use /proc/1988/oom_score_adj instead.

Synthesizing initial hotplug events

mmc0: new high speed DDR MMC card at address 0001

mmcblk0: mmc0:0001 MMC04G 3.52 GiB

mmcblk0boot0: mmc0:0001 MMC04G partition 1 16.0 MiB

mmcblk0boot1: mmc0:0001 MMC04G partition 2 16.0 MiB

mmcblk0: p1 p2 p3 p4

mmcblk0boot1: unknown partition table

mmcblk0boot0: unknown partition table

g_file_storage gadget: high speed config #1

mmc2: queuing unknown CIS tuple 0x01 (3 bytes)

mmc2: queuing unknown CIS tuple 0x1a (5 bytes)

mmc2: queuing unknown CIS tuple 0x1b (8 bytes)

mmc2: queuing unknown CIS tuple 0x14 (0 bytes)

mmc2: queuing unknown CIS tuple 0x80 (1 bytes)

mmc2: queuing unknown CIS tuple 0x81 (1 bytes)

mmc2: queuing unknown CIS tuple 0x82 (1 bytes)

mmc2: new high speed SDIO card at address 0001

mmc3: queuing unknown CIS tuple 0x01 (3 bytes)

mmc3: queuing unknown CIS tuple 0x1a (5 bytes)

mmc3: queuing unknown CIS tuple 0x1b (8 bytes)

mmc3: queuing unknown CIS tuple 0x14 (0 bytes)

mmc3: queuing unknown CIS tuple 0x80 (1 bytes)

mmc3: queuing unknown CIS tuple 0x81 (1 bytes)

mmc3: queuing unknown CIS tuple 0x82 (1 bytes)

mmc3: new high speed SDIO card at address 0001

uuc 0.4 [built Aug 16 2013 01:24:08]

UTP: Waiting for device to appear

UTP: file/device node /dev/utp already exists

cpu_id is 0

UTP: received command '$ ls /dev/*'

UTP: executing "ls /dev/*"

/dev/XOR /dev/ptyu7 /dev/ttyda

/dev/apm_bios /dev/ptyu8 /dev/ttydb

/dev/console /dev/ptyu9 /dev/ttydc

/dev/cpu_dma_latency /dev/ptyua /dev/ttydd

/dev/crypto /dev/ptyub /dev/ttyde

/dev/fb /dev/ptyuc /dev/ttydf

/dev/fb0 /dev/ptyud /dev/ttye0

/dev/fb1 /dev/ptyue /dev/ttye1

/dev/fb2 /dev/ptyuf /dev/ttye2

/dev/fb3 /dev/ptyv0 /dev/ttye3

/dev/fb4 /dev/ptyv1 /dev/ttye4

/dev/full /dev/ptyv2 /dev/ttye5

/dev/i2c-0 /dev/ptyv3 /dev/ttye6

/dev/i2c-1 /dev/ptyv4 /dev/ttye7

/dev/i2c-2 /dev/ptyv5 /dev/ttye8

/dev/kmem /dev/ptyv6 /dev/ttye9

/dev/kmsg /dev/ptyv7 /dev/ttyea

/dev/loop0 /dev/ptyv8 /dev/ttyeb

/dev/loop1 /dev/ptyv9 /dev/ttyec

/dev/loop2 /dev/ptyva /dev/ttyed

/dev/loop3 /dev/ptyvb /dev/ttyee

/dev/loop4 /dev/ptyvc /dev/ttyef

/dev/loop5 /dev/ptyvd /dev/ttymxc1

/dev/loop6 /dev/ptyve /dev/ttymxc2

/dev/loop7 /dev/ptyvf /dev/ttymxc3

/dev/mem /dev/ptyw0 /dev/ttyp0

/dev/mmcblk0 /dev/ptyw1 /dev/ttyp1

/dev/mmcblk0boot0 /dev/ptyw2 /dev/ttyp2

/dev/mmcblk0boot1 /dev/ptyw3 /dev/ttyp3

/dev/mmcblk0p1 /dev/ptyw4 /dev/ttyp4

/dev/mmcblk0p2 /dev/ptyw5 /dev/ttyp5

/dev/mmcblk0p3 /dev/ptyw6 /dev/ttyp6

/dev/mmcblk0p4 /dev/ptyw7 /dev/ttyp7

/dev/mtd0 /dev/ptyw8 /dev/ttyp8

/dev/mtd0ro /dev/ptyw9 /dev/ttyp9

/dev/mtd1 /dev/ptywa /dev/ttypa

/dev/mtd1ro /dev/ptywb /dev/ttypb

/dev/mtdblock0 /dev/ptywc /dev/ttypc

/dev/mtdblock1 /dev/ptywd /dev/ttypd

/dev/mxc_asrc /dev/ptywe /dev/ttype

/dev/mxc_hdmi /dev/ptywf /dev/ttypf

/dev/mxc_ipu /dev/ptyx0 /dev/ttyq0

/dev/mxc_mem /dev/ptyx1 /dev/ttyq1

/dev/mxc_vpu /dev/ptyx2 /dev/ttyq2

/dev/mxs_viim /dev/ptyx3 /dev/ttyq3

/dev/network_latency /dev/ptyx4 /dev/ttyq4

/dev/network_throughput /dev/ptyx5 /dev/ttyq5

/dev/null /dev/ptyx6 /dev/ttyq6

/dev/psaux /dev/ptyx7 /dev/ttyq7

/dev/ptmx /dev/ptyx8 /dev/ttyq8

/dev/ptya0 /dev/ptyx9 /dev/ttyq9

/dev/ptya1 /dev/ptyxa /dev/ttyqa

/dev/ptya2 /dev/ptyxb /dev/ttyqb

/dev/ptya3 /dev/ptyxc /dev/ttyqc

/dev/ptya4 /dev/ptyxd /dev/ttyqd

/dev/ptya5 /dev/ptyxe /dev/ttyqe

/dev/ptya6 /dev/ptyxf /dev/ttyqf

/dev/ptya7 /dev/ptyy0 /dev/ttyr0

/dev/ptya8 /dev/ptyy1 /dev/ttyr1

/dev/ptya9 /dev/ptyy2 /dev/ttyr2

/dev/ptyaa /dev/ptyy3 /dev/ttyr3

/dev/ptyab /dev/ptyy4 /dev/ttyr4

/dev/ptyac /dev/ptyy5 /dev/ttyr5

/dev/ptyad /dev/ptyy6 /dev/ttyr6

/dev/ptyae /dev/ptyy7 /dev/ttyr7

/dev/ptyaf /dev/ptyy8 /dev/ttyr8

/dev/ptyb0 /dev/ptyy9 /dev/ttyr9

/dev/ptyb1 /dev/ptyya /dev/ttyra

/dev/ptyb2 /dev/ptyyb /dev/ttyrb

/dev/ptyb3 /dev/ptyyc /dev/ttyrc

/dev/ptyb4 /dev/ptyyd /dev/ttyrd

/dev/ptyb5 /dev/ptyye /dev/ttyre

/dev/ptyb6 /dev/ptyyf /dev/ttyrf

/dev/ptyb7 /dev/ptyz0 /dev/ttys0

/dev/ptyb8 /dev/ptyz1 /dev/ttys1

/dev/ptyb9 /dev/ptyz2 /dev/ttys2

/dev/ptyba /dev/ptyz3 /dev/ttys3

/dev/ptybb /dev/ptyz4 /dev/ttys4

/dev/ptybc /dev/ptyz5 /dev/ttys5

/dev/ptybd /dev/ptyz6 /dev/ttys6

/dev/ptybe /dev/ptyz7 /dev/ttys7

/dev/ptybf /dev/ptyz8 /dev/ttys8

/dev/ptyc0 /dev/ptyz9 /dev/ttys9

/dev/ptyc1 /dev/ptyza /dev/ttysa

/dev/ptyc2 /dev/ptyzb /dev/ttysb

/dev/ptyc3 /dev/ptyzc /dev/ttysc

/dev/ptyc4 /dev/ptyzd /dev/ttysd

/dev/ptyc5 /dev/ptyze /dev/ttyse

/dev/ptyc6 /dev/ptyzf /dev/ttysf

/dev/ptyc7 /dev/random /dev/ttyt0

/dev/ptyc8 /dev/rfkill /dev/ttyt1

/dev/ptyc9 /dev/rtc /dev/ttyt2

/dev/ptyca /dev/rtc0 /dev/ttyt3

/dev/ptycb /dev/tracebuf /dev/ttyt4

/dev/ptycc /dev/tty /dev/ttyt5

/dev/ptycd /dev/tty0 /dev/ttyt6

/dev/ptyce /dev/tty1 /dev/ttyt7

/dev/ptycf /dev/tty10 /dev/ttyt8

/dev/ptyd0 /dev/tty11 /dev/ttyt9

/dev/ptyd1 /dev/tty12 /dev/ttyta

/dev/ptyd2 /dev/tty13 /dev/ttytb

/dev/ptyd3 /dev/tty14 /dev/ttytc

/dev/ptyd4 /dev/tty15 /dev/ttytd

/dev/ptyd5 /dev/tty16 /dev/ttyte

/dev/ptyd6 /dev/tty17 /dev/ttytf

/dev/ptyd7 /dev/tty18 /dev/ttyu0

/dev/ptyd8 /dev/tty19 /dev/ttyu1

/dev/ptyd9 /dev/tty2 /dev/ttyu2

/dev/ptyda /dev/tty20 /dev/ttyu3

/dev/ptydb /dev/tty21 /dev/ttyu4

/dev/ptydc /dev/tty22 /dev/ttyu5

/dev/ptydd /dev/tty23 /dev/ttyu6

/dev/ptyde /dev/tty24 /dev/ttyu7

/dev/ptydf /dev/tty25 /dev/ttyu8

/dev/ptye0 /dev/tty26 /dev/ttyu9

/dev/ptye1 /dev/tty27 /dev/ttyua

/dev/ptye2 /dev/tty28 /dev/ttyub

/dev/ptye3 /dev/tty29 /dev/ttyuc

/dev/ptye4 /dev/tty3 /dev/ttyud

/dev/ptye5 /dev/tty30 /dev/ttyue

/dev/ptye6 /dev/tty31 /dev/ttyuf

/dev/ptye7 /dev/tty32 /dev/ttyv0

/dev/ptye8 /dev/tty33 /dev/ttyv1

/dev/ptye9 /dev/tty34 /dev/ttyv2

/dev/ptyea /dev/tty35 /dev/ttyv3

/dev/ptyeb /dev/tty36 /dev/ttyv4

/dev/ptyec /dev/tty37 /dev/ttyv5

/dev/ptyed /dev/tty38 /dev/ttyv6

/dev/ptyee /dev/tty39 /dev/ttyv7

/dev/ptyef /dev/tty4 /dev/ttyv8

/dev/ptyp0 /dev/tty40 /dev/ttyv9

/dev/ptyp1 /dev/tty41 /dev/ttyva

/dev/ptyp2 /dev/tty42 /dev/ttyvb

/dev/ptyp3 /dev/tty43 /dev/ttyvc

/dev/ptyp4 /dev/tty44 /dev/ttyvd

/dev/ptyp5 /dev/tty45 /dev/ttyve

/dev/ptyp6 /dev/tty46 /dev/ttyvf

/dev/ptyp7 /dev/tty47 /dev/ttyw0

/dev/ptyp8 /dev/tty48 /dev/ttyw1

/dev/ptyp9 /dev/tty49 /dev/ttyw2

/dev/ptypa /dev/tty5 /dev/ttyw3

/dev/ptypb /dev/tty50 /dev/ttyw4

/dev/ptypc /dev/tty51 /dev/ttyw5

/dev/ptypd /dev/tty52 /dev/ttyw6

/dev/ptype /dev/tty53 /dev/ttyw7

/dev/ptypf /dev/tty54 /dev/ttyw8

/dev/ptyq0 /dev/tty55 /dev/ttyw9

/dev/ptyq1 /dev/tty56 /dev/ttywa

/dev/ptyq2 /dev/tty57 /dev/ttywb

/dev/ptyq3 /dev/tty58 /dev/ttywc

/dev/ptyq4 /dev/tty59 /dev/ttywd

/dev/ptyq5 /dev/tty6 /dev/ttywe

/dev/ptyq6 /dev/tty60 /dev/ttywf

/dev/ptyq7 /dev/tty61 /dev/ttyx0

/dev/ptyq8 /dev/tty62 /dev/ttyx1

/dev/ptyq9 /dev/tty63 /dev/ttyx2

/dev/ptyqa /dev/tty7 /dev/ttyx3

/dev/ptyqb /dev/tty8 /dev/ttyx4

/dev/ptyqc /dev/tty9 /dev/ttyx5

/dev/ptyqd /dev/ttya0 /dev/ttyx6

/dev/ptyqe /dev/ttya1 /dev/ttyx7

/dev/ptyqf /dev/ttya2 /dev/ttyx8

/dev/ptyr0 /dev/ttya3 /dev/ttyx9

/dev/ptyr1 /dev/ttya4 /dev/ttyxa

/dev/ptyr2 /dev/ttya5 /dev/ttyxb

/dev/ptyr3 /dev/ttya6 /dev/ttyxc

/dev/ptyr4 /dev/ttya7 /dev/ttyxd

/dev/ptyr5 /dev/ttya8 /dev/ttyxe

/dev/ptyr6 /dev/ttya9 /dev/ttyxf

/dev/ptyr7 /dev/ttyaa /dev/ttyy0

/dev/ptyr8 /dev/ttyab /dev/ttyy1

/dev/ptyr9 /dev/ttyac /dev/ttyy2

/dev/ptyra /dev/ttyad /dev/ttyy3

/dev/ptyrb /dev/ttyae /dev/ttyy4

/dev/ptyrc /dev/ttyaf /dev/ttyy5

/dev/ptyrd /dev/ttyb0 /dev/ttyy6

/dev/ptyre /dev/ttyb1 /dev/ttyy7

/dev/ptyrf /dev/ttyb2 /dev/ttyy8

/dev/ptys0 /dev/ttyb3 /dev/ttyy9

/dev/ptys1 /dev/ttyb4 /dev/ttyya

/dev/ptys2 /dev/ttyb5 /dev/ttyyb

/dev/ptys3 /dev/ttyb6 /dev/ttyyc

/dev/ptys4 /dev/ttyb7 /dev/ttyyd

/dev/ptys5 /dev/ttyb8 /dev/ttyye

/dev/ptys6 /dev/ttyb9 /dev/ttyyf

/dev/ptys7 /dev/ttyba /dev/ttyz0

/dev/ptys8 /dev/ttybb /dev/ttyz1

/dev/ptys9 /dev/ttybc /dev/ttyz2

/dev/ptysa /dev/ttybd /dev/ttyz3

/dev/ptysb /dev/ttybe /dev/ttyz4

/dev/ptysc /dev/ttybf /dev/ttyz5

/dev/ptysd /dev/ttyc0 /dev/ttyz6

/dev/ptyse /dev/ttyc1 /dev/ttyz7

/dev/ptysf /dev/ttyc2 /dev/ttyz8

/dev/ptyt0 /dev/ttyc3 /dev/ttyz9

/dev/ptyt1 /dev/ttyc4 /dev/ttyza

/dev/ptyt2 /dev/ttyc5 /dev/ttyzb

/dev/ptyt3 /dev/ttyc6 /dev/ttyzc

/dev/ptyt4 /dev/ttyc7 /dev/ttyzd

/dev/ptyt5 /dev/ttyc8 /dev/ttyze

/dev/ptyt6 /dev/ttyc9 /dev/ttyzf

/dev/ptyt7 /dev/ttyca /dev/ubi_ctrl

/dev/ptyt8 /dev/ttycb /dev/urandom

/dev/ptyt9 /dev/ttycc /dev/utp

/dev/ptyta /dev/ttycd /dev/vcs

/dev/ptytb /dev/ttyce /dev/vcs1

/dev/ptytc /dev/ttycf /dev/vcsa

/dev/ptytd /dev/ttyd0 /dev/vcsa1

/dev/ptyte /dev/ttyd1 /dev/vhci

/dev/ptytf /dev/ttyd2 /dev/video16

/dev/ptyu0 /dev/ttyd3 /dev/video17

/dev/ptyu1 /dev/ttyd4 /dev/video18

/dev/ptyu2 /dev/ttyd5 /dev/video19

/dev/ptyu3 /dev/ttyd6 /dev/video20

/dev/ptyu4 /dev/ttyd7 /dev/watchdog

/dev/ptyu5 /dev/ttyd8 /dev/zero

/dev/ptyu6 /dev/ttyd9

/dev/disk:

by-id by-path by-uuid

/dev/input:

mice uinput

/dev/pts:

/dev/shm:

/dev/snd:

timer

UTP: sending Success to kernel for command $ ls /dev/*.

utp_poll: pass returned.

UTP: received command '$ dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=1536 count=16'

UTP: executing "dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=1536 count=16"

16+0 records in

16+0 records out

8192 bytes (8.0KB) copied, 0.080471 seconds, 99.4KB/s

UTP: sending Success to kernel for command $ dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=1536 count=16.

utp_poll: pass returned.

UTP: received command '$ dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=8192 count=3'

UTP: executing "dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=8192 count=3"

3+0 records in

3+0 records out

1536 bytes (1.5KB) copied, 0.038287 seconds, 39.2KB/s

UTP: sending Success to kernel for command $ dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=8192 count=3.

utp_poll: pass returned.

UTP: received command '$ echo 0 > /sys/block/mmcblk0boot0/force_ro'

UTP: executing "echo 0 > /sys/block/mmcblk0boot0/force_ro"

UTP: sending Success to kernel for command $ echo 0 > /sys/block/mmcblk0boot0/force_ro.

utp_poll: pass returned.

UTP: received command 'send'

UTP: sending Success to kernel for command send.

UTP: received command '$ dd if=$FILE of=/dev/mmcblk0boot0 bs=512 seek=2 skip=2'

UTP: executing "dd if=$FILE of=/dev/mmcblk0boot0 bs=512 seek=2 skip=2"

844+1 records in

844+1 records out

432224 bytes (422.1KB) copied, 0.766364 seconds, 550.8KB/s

UTP: sending Success to kernel for command $ dd if=$FILE of=/dev/mmcblk0boot0 bs=512 seek=2 skip=2.

utp_poll: pass returned.

UTP: received command '$ echo 1 > /sys/block/mmcblk0boot0/force_ro'

UTP: executing "echo 1 > /sys/block/mmcblk0boot0/force_ro"

UTP: sending Success to kernel for command $ echo 1 > /sys/block/mmcblk0boot0/force_ro.

utp_poll: pass returned.

UTP: received command '$ echo 8 > /sys/devices/platform/sdhci-esdhc-imx.3/mmc_host/mmc0/mmc0:0001/boot_config'

UTP: executing "echo 8 > /sys/devices/platform/sdhci-esdhc-imx.3/mmc_host/mmc0/mmc0:0001/boot_config"

UTP: sending Success to kernel for command $ echo 8 > /sys/devices/platform/sdhci-esdhc-imx.3/mmc_host/mmc0/mmc0:0001/boot_config.

utp_poll: pass returned.

UTP: received command 'send'

UTP: sending Success to kernel for command send.

UTP: received command '$ dd if=$FILE of=/dev/mmcblk0 bs=20M seek=1 conv=fsync'

UTP: executing "dd if=$FILE of=/dev/mmcblk0 bs=20M seek=1 conv=fsync"

0+1 records in

0+1 records out

3379420 bytes (3.2MB) copied, 0.776460 seconds, 4.2MB/s

UTP: sending Success to kernel for command $ dd if=$FILE of=/dev/mmcblk0 bs=20M seek=1 conv=fsync.

utp_poll: pass returned.

UTP: received command 'send'

UTP: sending Success to kernel for command send.

UTP: received command '$ dd if=$FILE of=/dev/mmcblk0 bs=26M seek=1 conv=fsync'

UTP: executing "dd if=$FILE of=/dev/mmcblk0 bs=26M seek=1 conv=fsync"

0+1 records in

0+1 records out

3379420 bytes (3.2MB) copied, 1.313356 seconds, 2.5MB/s

UTP: sending Success to kernel for command $ dd if=$FILE of=/dev/mmcblk0 bs=26M seek=1 conv=fsync.

utp_poll: pass returned.

UTP: received command 'send'

UTP: sending Success to kernel for command send.

UTP: received command '$ tar xf $FILE '

UTP: executing "tar xf $FILE "

UTP: sending Success to kernel for command $ tar xf $FILE .

utp_poll: pass returned.

UTP: received command '$ sh eMMC-Partition.sh /dev/mmcblk0'

UTP: executing "sh eMMC-Partition.sh /dev/mmcblk0"

1+0 records in

1+0 records out

1024 bytes (1.0KB) copied, 0.003856 seconds, mmcblk0: unknown partition table

259.3KB/s

Checking that no-one is using this disk right now ...

OK

Disk /dev/mmcblk0: 115456 cylinders, 4 heads, 16 sectors/track

sfdisk: ERROR: sector 0 does not have an msdos signature

/dev/mmcblk0: unrecognized partition table type

Old situation:

No partitions found

New situation:

Units = mebibytes of 1048576 bytes, blocks of 1024 bytes, counting from 0

Device Boot Start End MiB #blocks Id System

/dev/mmcblk0p1 50 399 350 358400 83 Linux

/dev/mmcblk0p2 450 799 350 358400 83 Linux

/dev/mmcblk0p3 850 1849 1000 1024000 83 Linux

/dev/mmcblk0p4 2000 3607 1608 1646592 83 Linux

Warning: no primary partition is marked bootable (active)

This does not matter for LILO, but the DOS MBR will not boot this disk.

Successfully wrote the new partition table

Re-reading the partition table ...

mmcblk0: p1 p2 p3 p4

If you created or changed a DOS partition, /dev/foo7, say, then use dd(1)

to zero the first 512 bytes: dd if=/dev/zero of=/dev/foo7 bs=512 count=1

(See fdisk(8).)

UTP: sending Success to kernel for command $ sh eMMC-Partition.sh /dev/mmcblk0.

utp_poll: pass returned.

UTP: received command '$ mkfs.ext3 -j /dev/mmcblk0p1'

UTP: executing "mkfs.ext3 -j /dev/mmcblk0p1"

mke2fs 1.41.4 (27-Jan-2009)

Filesystem label=

OS type: Linux

Block size=1024 (log=0)

Fragment size=1024 (log=0)

89760 inodes, 358400 blocks

17920 blocks (5.00%) reserved for the super user

First data block=1

Maximum filesystem blocks=67633152

44 block groups

8192 blocks per group, 8192 fragments per group

2040 inodes per group

Superblock backups stored on blocks:

8193, 24577, 40961, 57345, 73729, 204801, 221185

Writing inode tables: 0/44 1/44 2/44 3/44 4/44 5/44 6/44 7/44 8/44 9/4410/4411/4412/4413/4414/4415/4416/4417/4418/4419/4420/4421/4422/4423/4424/4425/4426/4427/4428/4429/4430/4431/4432/4433/4434/4435/4436/4437/4438/4439/4440/4441/4442/4443/44done

Creating journal (8192 blocks): done

Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 37 mounts or

180 days, whichever comes first. Use tune2fs -c or -i to override.

UTP: sending Success to kernel for command $ mkfs.ext3 -j /dev/mmcblk0p1.

utp_poll: pass returned.

UTP: received command '$ mkdir -p /mnt/mmcblk0p1'

UTP: executing "mkdir -p /mnt/mmcblk0p1"

UTP: sending Success to kernel for command $ mkdir -p /mnt/mmcblk0p1.

utp_poll: pass returned.

UTP: received command '$ mount -t ext3 /dev/mmcblk0p1 /mnt/mmcblk0p1'

UTP: executing "mount -t ext3 /dev/mmcblk0p1 /mnt/mmcblk0pEXT3-fs: barriers not enabled

1"

kjournald starting. Commit interval 5 seconds

EXT3-fs (mmcblk0p1): using internal journal

EXT3-fs (mmcblk0p1): mounted filesystem with writeback data mode

UTP: sending Success to kernel for command $ mount -t ext3 /dev/mmcblk0p1 /mnt/mmcblk0p1.

utp_poll: pass returned.

UTP: received command 'pipe tar -jxv -C /mnt/mmcblk0p1'

pid is 3406, UTP: executing "tar -jxv -C /mnt/mmcblk0p1"

UTP: sending Success to kernel for command pipe tar -jxv -C /mnt/mmcblk0p1.

./

./home/

./home/sshd/

./home/cardinit.sh

./home/ath6k/

./home/ath6k/AR6003/

./home/ath6k/AR6003/hw2.1.1/

./home/ath6k/AR6003/hw2.1.1/athtcmd_ram.bin

./home/ath6k/AR6003/hw2.1.1/data.patch.hw3_0.bin

./home/ath6k/AR6003/hw2.1.1/athwlan.bin

./home/ath6k/AR6003/hw2.1.1/otp.bin

./home/ath6k/AR6003/hw2.1.1/athwlan_router.bin

./home/ath6k/AR6003/hw2.1.1/athwlan_mobile.bin

./home/ath6k/AR6003/hw2.1.1/fakeBoardData_AR6003_v2_0.bin

./home/CV1/

./home/CV1/lumencert.pem

./home/CV1/CV1_factory_config.bin

./home/CV1/commn_resp.bin

./home/CV1/Lib/

./home/CV1/Lib/libWebMngr.so

./home/CV1/Lib/libDispHndlr_Lib.so

./home/CV1/Lib/libWebMngr_Lib.so

./home/CV1/Lib/libSecCntrlr_Lib.so

./home/CV1/Lib/libFwUtils_Lib.so

./home/CV1/Lib/libPriCntrlr_Lib.so

./home/CV1/Lib/libConfigUtils_Lib.so

./home/CV1/Lib/libIrHndlr_Lib.so

./home/CV1/Lib/libSysUtils_Lib.so

./home/CV1/Lib/libDataIntrptr_Lib.so

./home/CV1/Lib/libErrLogger_Lib.so

./home/CV1/Lib/libDataLogger_Lib.so

./home/CV1/Lib/libStartupDiagUtils_Lib.so

./home/CV1/Lib/libConnMon_Lib.so

./home/CV1/Lib/libCommMngr_Lib.so

./home/CV1/Lib/libCV1_Utils_Lib.so

./home/CV1/CV1_factory_user_info.bin

./home/CV1/web/

./home/CV1/web/htdocs/

./home/CV1/web/htdocs/misc/

./home/CV1/web/htdocs/misc/WebMngr_Interface.c

./home/CV1/web/htdocs/misc/WebMngr_Interface.h

./home/CV1/web/htdocs/static/

./home/CV1/web/htdocs/static/Web.config

./home/CV1/web/htdocs/static/datalog/

./home/CV1/web/htdocs/static/datalog/CV1DATA_0023aeaf8ee1_20140506_181501.csv

./home/CV1/web/htdocs/static/datalog/CV1DATA_0023aeaf8ee1_20140507_184545.csv

./home/CV1/web/htdocs/static/Read Me, Instructions, License, etc/

./home/CV1/web/htdocs/static/Read Me, Instructions, License, etc/License.html

./home/CV1/web/htdocs/static/Read Me, Instructions, License, etc/Premium Templates.url

./home/CV1/web/htdocs/static/Read Me, Instructions, License, etc/Remove Copyright.url

./home/CV1/web/htdocs/static/Read Me, Instructions, License, etc/Free Web Hosting.url

./home/CV1/web/htdocs/static/Read Me, Instructions, License, etc/files/

./home/CV1/web/htdocs/static/Read Me, Instructions, License, etc/files/zymic.gif

./home/CV1/web/htdocs/static/Read Me, Instructions, License, etc/files/background.gif

./home/CV1/web/htdocs/static/Read Me, Instructions, License, etc/files/style.css

./home/CV1/web/htdocs/static/Read Me, Instructions, License, etc/Instructions.html

./home/CV1/web/htdocs/static/Read Me, Instructions, License, etc/Template Customization.url

./home/CV1/web/htdocs/static/styles/

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/upload/

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/upload/.upload.pdoc.yaml

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/upload/upload_src.js

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/upload/change.png

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/upload/remove.png

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/upload/progress.gif

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/upload/upload.css

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/upload/warning.png

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/upload/loading.gif

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/upload/upload.js

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/upload/ok.png

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/upload/progress-red.gif

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/left-range.png

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/.datepicker.pdoc.yaml

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/datepicker.css

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/datepicker_src.js

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/svn-commit.tmp

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/locales/

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/locales/.pt_BR.pdoc.yaml

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/locales/.lt_LT.pdoc.yaml

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/locales/.ru_RU.pdoc.yaml

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/locales/.nl_NL.pdoc.yaml

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/locales/nl_NL.js

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/locales/.cs_CZ.pdoc.yaml

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/locales/.it_IT.pdoc.yaml

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/locales/el_GR.js

./home/CV1/web/htdocs/static/styles/protoplasm-0.2b2/datepicker/locales/pl_PL.js

At this point the kernel splash image is loaded

/home/plat_LOCAL_i686-SDIO.sh: exit: line 141: Illegal number: -1

Platform script failed : loadAR6K

loadAR6000.sh: exit: line 344: Illegal number: -1

Platform set to LOCAL_i686-SDIO

Platform Setup Script is: /home/plat_LOCAL_i686-SDIO.sh

Image path: /home

Mac address:

sdiostack loading

loading AR6K module... Args = (bmienable=1 ifname=uap0 busspeedlow=0) , logfile:/tmp/dbglog.out

insmod: can't insert '/home/ar6000.ko': unknown symbol in module, or unknown parameter

*** Failed to install AR6K Module

/home/plat_LOCAL_i686-SDIO.sh: exit: line 141: Illegal number: -1

Platform script failed : loadAR6K

loadAR6000.sh: exit: line 344: Illegal number: -1

AR6k module load Done...

Generating public/private rsa1 key pair.

ifconfig: SIOCGIFFLAGS: No such device

killall: hostapd: no process killed

killall: udhcpd: no process killed

ifconfig: SIOCGIFFLAGS: No such device

error, Failure parsing line 87 of /etc/udhcpd.uap0.conf

error, Failure parsing line 88 of /etc/udhcpd.uap0.conf

info, udhcpd (v0.9.9-pre) started

error, SIOCGIFADDR failed, is the interface up and configured?: No such device

Configuration file: /home/hostapd.conf

Line 3: invalid SSID ''

1 errors found in configuration file '/home/hostapd.conf'

killall: udhcpc,: no process killed

killall: wpa_supplicant: no process killed

ifconfig: SIOCGIFFLAGS: No such device

0x0c0001, Invalid argument

0x0c0055, Error in settings station configurations

0x0c006c, Error in setting configuration

0x090063, Error in ConfigUtils_set_nw_conf()

0x0b0005, Error in kill():No such process

killall: dhclient: no process killed

killall: udhcpc: no process killed

killall: udhcpd: no process killed

killall: hostapd: no process killed

0x09002c, Error in CentrlContrlr_init_modules

Your identification has been saved in /etc/openssh/ssh_host_key.

Your public key has been saved in /etc/openssh/ssh_host_key.pub.

The key fingerprint is:

8e:fa:11:18:ee:c0:6c:75:cb:31:db:33:56:1f:8c:a3 root@SABRE_SDB

The key's randomart image is:

+--[RSA1 2048]----+

| |

| o |

| o + + o |

| o o = * o o . |

| = o = E . |

| . o = o |

| . o . |

| . . |

| ... |

+-----------------+

Generating public/private dsa key pair.

Your identification has been saved in /etc/openssh/ssh_host_dsa_key.

Your public key has been saved in /etc/openssh/ssh_host_dsa_key.pub.

The key fingerprint is:

8c:54:0f:a9:89:b1:13:09:f7:1f:31:bc:ae:6d:ad:f2 root@SABRE_SDB

The key's randomart image is:

+--[ DSA 1024]----+

| .... .=. |

| .+. .o= |

| =oo... |

| +.o+.. |

| ...S |

| . |

| o . |

| o o . |

| +E. |

+-----------------+

Generating public/private rsa key pair.

Your identification has been saved in /etc/openssh/ssh_host_rsa_key.

Your public key has been saved in /etc/openssh/ssh_host_rsa_key.pub.

The key fingerprint is:

b8:15:0e:66:bd:ac:23:8b:11:63:78:63:1d:eb:25:ac root@SABRE_SDB

The key's randomart image is:

+--[ RSA 2048]----+

| |

| . |

| . + o |

| . o = = o |

|. B = o S |

| + * o + |

| E o + |

| o o . |

| . . |

+-----------------+

Generating public/private ecdsa key pair.

Your identification has been saved in /etc/openssh/ssh_host_ecdsa_key.

Your public key has been saved in /etc/openssh/ssh_host_ecdsa_key.pub.

The key fingerprint is:

f9:d3:f9:ce:63:24:3c:22:4f:cb:fc:68:d5:d2:2b:c5 root@SABRE_SDB

The key's randomart image is:

+--[ECDSA 256]---+

| |

| . |

| S . + |

| ..o.*.E |

| *o+o* . |

| *o.o+ |

| ....++. |

+-----------------+

Starting /usr/sbin/sshd: Could not load host key: /etc/openssh/ssh_host_ed25519_key

[ OK ]

/etc/init.d/S64-apache-httpd: Creating system user 'daemon' with generic settings. Review and modify as required.

Starting apache-httpd

BusyBox v1.20.2 (2014-07-11 16:18:48 IST) built-in shell (ash)

Enter 'help' for a list of built-in commands.

#-1

AR6k module load Done...

ifconfig: SIOCGIFFLAGS: No such device

killall: hostapd: no process killed

Starting /usr/sbin/sshd: killall: udhcpd: no process killed

Could not load host key: /etc/openssh/ssh_host_rsa_key

Could not load host key: /etc/openssh/ssh_host_dsa_key

Could not load host key: /etc/openssh/ssh_host_ecdsa_key

Could not load host key: /etc/openssh/ssh_host_ed25519_key

Disabling protocol version 2. Could not load host key

sshd: no hostkeys available -- exiting.

[FAIL]

/etc/init.d/S50-openssh: Error 1 starting /usr/sbin/sshd... bailing.

/etc/init.d/S64-apache-httpd: Creating system user 'daemon' with generic settings. Review and modify as required.

ifconfig: SIOCGIFFLAGS: No such device

error, Failure parsing line 87 of /etc/udhcpd.uap0.conf

error, Failure parsing line 88 of /etc/udhcpd.uap0.conf

info, udhcpd (v0.9.9-pre) started

error, SIOCGIFADDR failed, is the interface up and configured?: No such device

Configuration file: /home/hostapd.conf

Line 3: invalid SSID ''

1 errors found in configuration file '/home/hostapd.conf'

killall: udhcpc,: no process killed

killall: wpa_supplicant: no process killed

ifconfig: SIOCGIFFLAGS: No such device

0x0c0001, Invalid argument

0x0c0055, Error in settings station configurations

0x0c006c, Error in setting configuration

0x090063, Error in ConfigUtils_set_nw_conf()

0x0b0005, Error in kill():No such process

killall: dhclient: no process killed

killall: udhcpc: no process killed

killall: udhcpd: no process killed

killall: hostapd: no process killed

0x09002c, Error in CentrlContrlr_init_modules

Starting apache-httpd

(20014)Internal error: AH00058: Error retrieving pid file /var/run/httpd.pid

AH00059: Remove it before continuing if it is corrupted.

BusyBox v1.20.2 (2014-07-11 16:18:48 IST) built-in shell (ash)

Enter 'help' for a list of built-in commands.

Any help will be appreciated.

jaymind · ‎01-08-2015

Hello Divya,

Thanks for providing the logs..

but you provide 2 boot-up the logs in one :smileysad: create confusion,

but anyhow I find some lines and issues which are may be possible reasons.

At the same time if you provide your boot arguments then it easy to conclude, so please provide your complete boot arguments.

Some lines in your the logs I write it below,

You just find it out in the logs which you provided me.

The main reason why it happen it due to HDMI on fb1 and you ON the fb2 (I don't know you use of it or not but if not use then OFF unnecessary)

My suggestions to you that if you not use HDMI and LDB-XGA on fb2 then OFF that.

1.

Kernel command line: setenv bootargs ${bootargs} console=ttymxc1,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=adv739x,BT656-NTSC,if=BT656,fbpix=RGB565 video=mxcfb1:dev=hdmi,1280x720M@60,if=RGB24 video=mxcfb2:dev=ldb,LDB-XGA,if=RGB24,bpp=24,fbpix=BGR32 ldb=dul0 video=mxcfb3:off consoleblank=0

--> here problem it with your arguments and also HDMI.

just try it out some below arguments in U-boot and revert back with result. (don't save any argument, just see the result by real time changes in u-boot at the time of every restart.

If you not use HDMI and LDB-XGA then,

setenv bootargs ${bootargs} console=ttymxc1,115200 consoleblank=0 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=adv739x,BT656-NTSC,if=BT656,fbpix=RGB565 video=mxcfb1:off video=mxcfb2:off

setenv bootargs ${bootargs} console=ttymxc1,115200 consoleblank=0 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=adv739x,BT656-NTSC,if=BT656,fbpix=BGR32 video=mxcfb1:off video=mxcfb2:off

not sure about below :smileyconfused:

setenv bootargs ${bootargs} console=ttymxc1,115200 consoleblank=0 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=adv739x,BT656-NTSC,if=BT656,fbpix=RGB565 video=mxcfb1:dev=hdmi,1280x720M@60,if=RGB24,bpp=32 video=mxcfb2:off

2.

mxc_hdmi mxc_hdmi: Read EDID again

--> here due to your arguments it goes to HDMI connection and try to search/read EDID,

so because of this at that time your display gone black and LCD screens disappears.

3.

Kernel command line: console=ttymxc1,115200 rdinit=/linuxrc enable_wait_mode=off

I also found above line in the logs which would be incorrect, I think.

(You provide U-boot's arguments then after it will give some idea till its not clear)

enable_wait_mode=off is to let user has an options of turning off WAIT mode feature, such as when you suspect that some modules' performance are impacted by WAIT mode, then you can try to disable WAIT mode.

you can find more details about this here.... https://community.freescale.com/thread/307222

4. found 3 lines related to fb.0 which are in sequence as below

1.     mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver adv739x

------------

2.     mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver adv739x

-----------

3.     mxc_sdc_fb mxc_sdc_fb.0: NO mxc display driver found!

I don't know why these display twice may be it due to you provide me 2 boot up logs.

If you provide me 2 boot ups logs then 1st is correct in 1st log , 2nd is also correct in 2nd log but what about 3rd ??:smileyplain:

Its a problem here, it not found fb.0 after 2nd, its also a one of reason.

5. This point no more important anyway I put it here.

fbcvt: 1920x1080@60: CVT Name - 2.073M9

Console: switching to colour frame buffer device 240x67

mxc_sdc_fb mxc_sdc_fb.2: register mxc display driver ldb

_regulator_get: get() with no identifier

mxc_sdc_fb mxc_sdc_fb.3: register mxc display driver ldb

imx-sdma imx-sdma: loaded firmware 1.1

imx-sdma imx-sdma: initialized

mxc_hdmi mxc_hdmi: Read EDID again

mxc_hdmi mxc_hdmi: No modes read from edid

mxc_hdmi mxc_hdmi: create default modelist

fbcvt: 1920x1080@60: CVT Name - 2.073M9

Found above lines in end of log(2nd boot up log) which are corrects but in start of log(1st boot log) I also found as below..

mxc_hdmi mxc_hdmi: No modes read from edid

mxc_hdmi mxc_hdmi: create default modelist

fbcvt: 1280x720@60: CVT Name - .921M9

May these points helps you.

At the same time possible then please provide me U-boot's argument and try some arguments without saving in U-boot as per I described in point 1. :smileyhappy:

Inform me about your outputs and results.

Hope this will work.

Thanks and Regards

JAYMIN DABHI

divyardharan · ‎01-08-2015

Hi Jaymin,

Thank you for the findings.

The boot arguments we used was "setenv bootargs ${bootargs} console=ttymxc1,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=adv739x,BT656-NTSC,if=BT656,fbpix=RGB565 video=mxcfb1:dev=hdmi,1280x720M@60,if=RGB24 video=mxcfb2:dev=ldb,LDB-XGA,if=RGB24,bpp=24,fbpix=BGR32 ldb=dul0 video=mxcfb3:off consoleblank=0"

We tried with the above boot arguments but it didn't solve the issue.We are using lcd display.

when we tried the below arg, the kernel splash screen was loaded after a delay of 5 sec and stayed for 18 sec.But the application crashes. Kindly help..

"setenv bootargs ${bootargs} console=ttymxc1,115200 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=ldb,LDB-XGA,if=RGB24,bpp=24,fbpix=BGR32 ldb=dul0 video=mxcfb1:dev=hdmi,1280x720M@60,if=RGB24 video=mxcfb2:off video=mxcfb3:off consoleblank=0".

Please find the log below:

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 18

U-Boot 2009.08 (Jan 08 2015 - 18:44:16)

U-Boot code: 27800720 -> 278A7200 BSS: -> 278E11CC

CPU: Freescale i.MX6 family TO1.2 at 792 MHz

Thermal sensor with ratio = 173

Temperature: 37 C, calibration data 0x5484c469

mx6q pll1: 792MHz

mx6q pll2: 528MHz

mx6q pll3: 480MHz

mx6q pll8: 50MHz

ipg clock : 66000000Hz

ipg per clock : 66000000Hz

uart clock : 80000000Hz

cspi clock : 60000000Hz

ahb clock : 132000000Hz

axi clock : 264000000Hz

emi_slow clock: 132000000Hz

ddr clock : 528000000Hz

usdhc1 clock : 198000000Hz

usdhc2 clock : 198000000Hz

usdhc3 clock : 198000000Hz

usdhc4 clock : 198000000Hz

nfc clock : 24000000Hz

Board: i.MX6Q-SABRESD: unknown-board Board: 0x63012 [POR ]

Boot Device: MMC

RAM Configuration:

Bank #0: 10000000 1 GB

MMC: FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2,FSL_USDHC: 3

*** Warning - bad CRC or MMC, using default environment

[LCD] Initializing LCD frambuffer at 27b00000

lcd_clear[LCD] Drawing the logo...

lcd_logo 0 w <NULL>

splash image not null <NULL>splash_config_screen_align 660606637 w 0,0

splash pos not null 660606637 w 0,0

splash_posi 0

0Display-bmp: 600 x 400 with 256 colors

lcd_clearing

ipu_clk = 260000000

IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)

Framebuffer at 0x27b00000

mxcfb_init_fbinfo: 4 640 112 524

Framebuffer structures at: fbi=0x27602c50 mxcfbi=0x27602e60

allocated fb @ paddr=0x27B00000, size=3145728.

Channel already disabled 9

Channel already uninitialized 9

setup_disp_channel1 called

bpp_to_pixfmt: 16

init channel = 9

pixclock = 64998000l Hz

panel size = 1024 x 768

pixel clk = 64998000

setup_disp_channel2: 95ffcff 1024 768 2048 27b00000 27c80000

bpp_to_pixfmt: 16

initializing idma ch 23 @ 027005c0

IPU DMFC DP HIGH RES: 1(0,1), 5B(2~5), 5F(6,7)

ch 23 word 0 - 00000000 00000000 00000000 E0001800 000BFC7F

ch 23 word 1 - 04F90000 009EC000 20E3C000 F2C1FFC0 00082CA0

PFS 0x7, BPP 0x3, NPB 0xf

FW 1023, FH 767, Stride 2047

Width0 4+1, Width1 5+1, Width2 4+1, Width3 7+1, Offset0 0, Offset1 5, Offset2 11, Offset3 16

MXC IPUV3 configured

XRES = 1024 YRES = 768 BitsXpixel = 4

IPU_CONF = 0x00000660

IDMAC_CONF = 0x0000002F

IDMAC_CHA_EN1 = 0x00800000

IDMAC_CHA_EN2 = 0x00000000

IDMAC_CHA_PRI1 = 0x18800000

IDMAC_CHA_PRI2 = 0x00000000

IPU_CHA_DB_MODE_SEL0 = 0x00800000

IPU_CHA_DB_MODE_SEL1 = 0x00000000

DMFC_WR_CHAN = 0x00000090

DMFC_WR_CHAN_DEF = 0x202020F6

DMFC_DP_CHAN = 0x0000968A

DMFC_DP_CHAN_DEF = 0x2020F6F6

DMFC_IC_CTRL = 0x00000002

IPU_FS_PROC_FLOW1 = 0x00000000

IPU_FS_PROC_FLOW2 = 0x00000000

IPU_FS_PROC_FLOW3 = 0x00000000

IPU_FS_DISP_FLOW1 = 0x00000000

lcd_enabled

In: serial

Out: serial

Err: serial

Net: got MAC address from IIM: 00:10:2e:e0:00:02

FEC0 [PRIME]

### main_loop entered: bootdelay=3

### main_loop: bootcmd="run bootcmd_mmc"

Hit any key to stop autoboot: 3 2 1 0

********Power On Reset *****************

***Image validation flag=0******

*** Image Identifier flag is 1

Enabled Watch Dog Timer

System going to reboot within 120 sec, if watchdog not get feeding

file name=/

<2, 0, 204>

ext2fs read inode 2

ext2fs read 0 group descriptor (blkno 2 blkoff 0)

<4, 0, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 262 blkoff 128

<524, 128, 128>

ext2fs_read_block 00000205

<1034, 0, 8>

ext2fs_read_block 00000205

<1034, 8, 1>

iterate >.<

ext2fs read inode 2

ext2fs read 0 group descriptor (blkno 2 blkoff 0)

<4, 0, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 262 blkoff 128

<524, 128, 128>

<DIR> 1024 .

ext2fs_read_block 00000205

<1034, 12, 8>

ext2fs_read_block 00000205

<1034, 20, 2>

iterate >..<

ext2fs read inode 2

ext2fs read 0 group descriptor (blkno 2 blkoff 0)

<4, 0, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 262 blkoff 128

<524, 128, 128>

<DIR> 1024 ..

ext2fs_read_block 00000205

<1034, 24, 8>

ext2fs_read_block 00000205

<1034, 32, 10>

iterate >lost+found<

ext2fs read inode 11

ext2fs read 0 group descriptor (blkno 2 blkoff 0)

<4, 0, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 263 blkoff 256

<526, 256, 128>

<DIR> 12288 lost+found

ext2fs_read_block 00000205

<1034, 44, 8>

ext2fs_read_block 00000205

<1034, 52, 4>

iterate >home<

ext2fs read inode 22441

ext2fs read 11 group descriptor (blkno 2 blkoff 352)

<4, 352, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 90115 blkoff 0

<180230, 0, 128>

<DIR> 1024 home

ext2fs_read_block 00000205

<1034, 56, 8>

ext2fs_read_block 00000205

<1034, 64, 3>

iterate >mnt<

ext2fs read inode 2041

ext2fs read 1 group descriptor (blkno 2 blkoff 32)

<4, 32, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 8454 blkoff 0

<16908, 0, 128>

<DIR> 1024 mnt

ext2fs_read_block 00000205

<1034, 68, 8>

ext2fs_read_block 00000205

<1034, 76, 3>

iterate >etc<

ext2fs read inode 59161

ext2fs read 29 group descriptor (blkno 2 blkoff 928)

<5, 416, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 237571 blkoff 0

<475142, 0, 128>

<DIR> 1024 etc

ext2fs_read_block 00000205

<1034, 80, 8>

ext2fs_read_block 00000205

<1034, 88, 3>

iterate >lib<

ext2fs read inode 65281

ext2fs read 32 group descriptor (blkno 3 blkoff 0)

<6, 0, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 262147 blkoff 0

<524294, 0, 128>

<DIR> 3072 lib

ext2fs_read_block 00000205

<1034, 92, 8>

ext2fs_read_block 00000205

<1034, 100, 4>

iterate >root<

ext2fs read inode 10201

ext2fs read 5 group descriptor (blkno 2 blkoff 160)

<4, 160, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 41222 blkoff 0

<82444, 0, 128>

<DIR> 1024 root

ext2fs_read_block 00000205

<1034, 104, 8>

ext2fs_read_block 00000205

<1034, 112, 3>

iterate >dev<

ext2fs read inode 69361

ext2fs read 34 group descriptor (blkno 3 blkoff 64)

<6, 64, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 278531 blkoff 0

<557062, 0, 128>

<DIR> 16384 dev

ext2fs_read_block 00000205

<1034, 116, 8>

ext2fs_read_block 00000205

<1034, 124, 4>

iterate >sbin<

ext2fs read inode 63241

ext2fs read 31 group descriptor (blkno 2 blkoff 992)

<5, 480, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 253955 blkoff 0

<507910, 0, 128>

<DIR> 1024 sbin

ext2fs_read_block 00000205

<1034, 128, 8>

ext2fs_read_block 00000205

<1034, 136, 3>

iterate >usr<

ext2fs read inode 51001

ext2fs read 25 group descriptor (blkno 2 blkoff 800)

<5, 288, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 205062 blkoff 0

<410124, 0, 128>

<DIR> 1024 usr

ext2fs_read_block 00000205

<1034, 140, 8>

ext2fs_read_block 00000205

<1034, 148, 4>

iterate >proc<

ext2fs read inode 6121

ext2fs read 3 group descriptor (blkno 2 blkoff 96)

<4, 96, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 24838 blkoff 0

<49676, 0, 128>

<DIR> 1024 proc

ext2fs_read_block 00000205

<1034, 152, 8>

ext2fs_read_block 00000205

<1034, 160, 3>

iterate >opt<

ext2fs read inode 12241

ext2fs read 6 group descriptor (blkno 2 blkoff 192)

<4, 192, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 49155 blkoff 0

<98310, 0, 128>

<DIR> 1024 opt

ext2fs_read_block 00000205

<1034, 164, 8>

ext2fs_read_block 00000205

<1034, 172, 7>

iterate >linuxrc<

ext2fs read inode 6122

ext2fs read 3 group descriptor (blkno 2 blkoff 96)

<4, 96, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 24838 blkoff 128

<49676, 128, 128>

<SYM> 11 linuxrc

ext2fs_read_block 00000205

<1034, 180, 8>

ext2fs_read_block 00000205

<1034, 188, 3>

iterate >run<

ext2fs read inode 8161

ext2fs read 4 group descriptor (blkno 2 blkoff 128)

<4, 128, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 32771 blkoff 0

<65542, 0, 128>

<DIR> 1024 run

ext2fs_read_block 00000205

<1034, 192, 8>

ext2fs_read_block 00000205

<1034, 200, 6>

iterate >config<

ext2fs read inode 14281

ext2fs read 7 group descriptor (blkno 2 blkoff 224)

<4, 224, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 57606 blkoff 0

<115212, 0, 128>

<DIR> 1024 config

ext2fs_read_block 00000205

<1034, 208, 8>

ext2fs_read_block 00000205

<1034, 216, 3>

iterate >var<

ext2fs read inode 16321

ext2fs read 8 group descriptor (blkno 2 blkoff 256)

<4, 256, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 65539 blkoff 0

<131078, 0, 128>

<DIR> 1024 var

ext2fs_read_block 00000205

<1034, 220, 8>

ext2fs_read_block 00000205

<1034, 228, 3>

iterate >tmp<

ext2fs read inode 28561

ext2fs read 14 group descriptor (blkno 2 blkoff 448)

<4, 448, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 114691 blkoff 0

<229382, 0, 128>

<DIR> 1024 tmp

ext2fs_read_block 00000205

<1034, 232, 8>

ext2fs_read_block 00000205

<1034, 240, 3>

iterate >bin<

ext2fs read inode 20401

ext2fs read 10 group descriptor (blkno 2 blkoff 320)

<4, 320, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 81923 blkoff 0

<163846, 0, 128>

<DIR> 3072 bin

ext2fs_read_block 00000205

<1034, 244, 8>

ext2fs_read_block 00000205

<1034, 252, 3>

iterate >jre<

ext2fs read inode 18361

ext2fs read 9 group descriptor (blkno 2 blkoff 288)

<4, 288, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 73990 blkoff 0

<147980, 0, 128>

<DIR> 1024 jre

ext2fs_read_block 00000205

<1034, 256, 8>

ext2fs_read_block 00000205

<1034, 264, 3>

iterate >sys<

ext2fs read inode 4081

ext2fs read 2 group descriptor (blkno 2 blkoff 64)

<4, 64, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 16387 blkoff 0

<32774, 0, 128>

<DIR> 1024 sys

ext2fs_read_block 00000205

<1034, 268, 8>

ext2fs_read_block 00000205

<1034, 276, 5>

iterate >media<

ext2fs read inode 34681

ext2fs read 17 group descriptor (blkno 2 blkoff 544)

<5, 32, 32>

ext2fs read inode blkno 0 blkoff 0

ext2fs read inode blkno 139267 blkoff 0

<278534, 0, 128>

<DIR> 1024 media

*******************Execute Primary Image ***********

mmc3(part 0) is current device

MMC read: dev # 3, block # 40960, count 8192 ... 8192 blocks read: OK

* kernel: default image load address = 0x10800000

## Booting kernel from Legacy Image at 10800000 ...

****CV1 Kernel Validation Based on CRC Algorithm***

Image Name: Linux-3.0.35-ts-armv7l

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 3245188 Bytes = 3.1 MB

Load Address: 10008000

Entry Point: 10008000

Verifying Checksum ... OK

********Image validated********

kernel data at 0x10800040, len = 0x00318484 (3245188)

## No init Ramdisk

ramdisk start = 0x00000000, ramdisk end = 0x00000000

Loading Kernel Image ... OK

OK

kernel loaded at 0x10008000, end = 0x10320484

## Transferring control to Linux (at address 10008000) ...

Starting kernel ****bootm.c******...

init started: BusyBox v1.20.2 (2014-07-11 16:18:48 IST)

Setting hotplug handler: [ OK ]

Creating device files: Auto-mount of [/media/mmcblk0p1] successful

Auto-mount of [/media/mmcblk0p2] successful

Auto-mount of [/media/mmcblk0p3] successful

Auto-mount of [/media/mmcblk0p4] successful

[ OK ]

modprobe: module galcore not found in modules.dep

Setting timezone and system clock: hwclock: settimeofday: Invalid argument

[Fail]

Starting system logging.

Configuring network interfaces: done

Starting dbus: [ OK ]

Starting ntpd: [OK]

****Executing Custom Script************ CV1: /dev/mmcblk1p1$ Not Mounted ****

48

Error count=0****Startup Error logged:19700101, 5:30:20.000, 30

****insmod: can't insert '/home/CV1/Driver/gadgetfs.ko': unknown symbol in module, or unknown parameter

mount: mounting gadgetfs on /dev/gadget failed: No such device

AR6k module loading start...

Module Arguments...

Platform set to LOCAL_i686-SDIO

Platform Setup Script is: /home/plat_LOCAL_i686-SDIO.sh

Image path: /home

Mac address:

sdiostack loading

loading AR6K module... Args = (bmienable=1 ifname=wlan0 busspeedlow=0) , logfile:/tmp/dbglog.out

insmod: can't insert '/home/ar6000.ko': unknown symbol in module, or unknown parameter

*** Failed to install AR6K Module

/home/plat_LOCAL_i686-SDIO.sh: exit: line 141: Illegal number: -1

Platform script failed : loadAR6K

loadAR6000.sh: exit: line 344: Illegal number: -1

Platform set to LOCAL_i686-SDIO

Platform Setup Script is: /home/plat_LOCAL_i686-SDIO.sh

Image path: /home

Mac address:

sdiostack loading

loading AR6K module... Args = (bmienable=1 ifname=uap0 busspeedlow=0) , logfile:/tmp/dbglog.out

insmod: can't insert '/home/ar6000.ko': unknown symbol in module, or unknown parameter

*** Failed to install AR6K Module

/home/plat_LOCAL_i686-SDIO.sh: exit: line 141: Illegal number: -1

Platform script failed : loadAR6K

loadAR6000.sh: exit: line 344: Illegal number: -1

AR6k module load Done...

Starting /usr/sbin/sshd: ifconfig: SIOCGIFFLAGS: No such device

killall: hostapd: no process killed

killall: udhcpd: no process killed

Could not load host key: /etc/openssh/ssh_host_ed25519_key

[ OK ]

Starting apache-httpd

ifconfig: SIOCSIFADDR: No such device

info, udhcpd (v0.9.9-pre) started

error, max_leases value (234) not sane, setting to 9 instead

error, SIOCGIFADDR failed, is the interface up and configured?: No such device

Configuration file: /home/hostapd.conf

ioctl(SIOCGIFINDEX): No such device

ar6000 driver initialization failed.

rmdir[ctrl_interface]: No such file or directory

killall: udhcpc,: no process killed

killall: wpa_supplicant: no process killed

ifconfig: SIOCGIFFLAGS: No such device

Internet Systems Consortium DHCP Client V3.1-ESV-R3

For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:10:2e:e0:00:02

Sending on LPF/eth0/00:10:2e:e0:00:02

Sending on Socket/fallback

Internet Systems Consortium DHCP Client V3.1-ESV-R3

For info, please visit https://www.isc.org/software/dhcp/

0x100019, Log file create

0x100095, ErrLogger_appndr_dbg_file_open()

BusyBox v1.20.2 (2014-07-11 16:18:48 IST) built-in shell (ash)

Enter 'help' for a list of built-in commands.

QIconvCodec::convertFromUnicode: using Latin-1 for conversion, iconv_open failed

# httpd not running, trying to start

Could not read interface wlan0 flags: No such device

wlan0: Failed to initialize driver interface

0x100019, Log file create

0x100095, ErrLogger_appndr_dbg_file_open()

?? don't recognize /dev/gadget bulk device

/dev/gadget/(null) ep1 configured

serial="st3f4m1r8wr1mzay3d06budw4frd9dvyxa6yykjc6vyj70ppqdfln0rofs8cx2m"

Listening on LPF/eth0/00:10:2e:e0:00:02

Sending on LPF/eth0/00:10:2e:e0:00:02

Sending on Socket/fallback

0x100019, Log file create

0x100095, ErrLogger_appndr_dbg_file_open()

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 16

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4

No DHCPOFFERS received.

No working leases in persistent database - sleepin

Thanking you,

Divya

alejandrolozan1 · ‎01-12-2015

Hi Divya,

Were you able to solve this?

Which BSP version are you using? Can you share the steps to reproduce the same in one of our boards?

Alejandro

divyardharan · ‎01-12-2015

Hi Alejandro,

We are using version 3.0 for building ltib. The issue is not yet resolved.

Thanks,

divya

jaymind · ‎01-13-2015

Hello Divya,

try to use below arguments and let me know your result and observation whatever it is.

setenv bootargs ${bootargs} console=ttymxc1,115200 consoleblank=0 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=adv739x,BT656-NTSC,if=BT656,fbpix=RGB565 video=mxcfb1:off video=mxcfb2:off video=mxcfb3:off

setenv bootargs ${bootargs} console=ttymxc1,115200 consoleblank=0 ip=none root=/dev/mmcblk0p1 rootwait video=mxcfb0:dev=adv739x,BT656-NTSC,if=BT656,fbpix=RGB565 video=mxcfb1:off video=mxcfb2:off

NOTE : do it for test purpose,

Also please tell me in details that actually what things are doing at what timing ? (at proper time, what is displaying ?)

Regards

Jaymin D

divyardharan · ‎03-20-2015

Hi Jaimin,

Any updates on how to load the kernel splash screen once the u-boot splash screen is loaded.

Thanks ,

Divya

divyardharan · ‎01-13-2015

Hi Jaymin,

We tried with the above bootargs but nothing is displaying in lcd.Not showing boot loader and kernel splash screen.We tried to optimize the kernel by disabling the drivers.But the delay in loading kernel splash screen reduced to 16sec only from 18sec.

Also kindly help to optimize the kernel boot time of ltib.

Thanks,

Divya

delay between the boot loader and kernel splash screens

delay between the boot loader and kernel splash screens

i.MX6Quad