- Product Forums
- General Purpose Microcontrollers
- i.MX Forums
- class="nav-category mobile-label ">i.MX Securityi.MX Security
- class="nav-category mobile-label ">i.MX Trainingi.MX Training
- i.MX Processors
- i.MX RT
- i.MX Solutions
- i.MX 한국어 커뮤니티
- i.MX Graphics
- i.MX8 Coral Development Kit
-
- QorIQ Processing Platforms
- Identification and Security
- Power Management
-
- Software Forums
- MCUXpresso Software and Tools
- class="nav-category mobile-label ">MCUX SDK DevelopmentMCUX SDK Development
- MCUXpresso General
- MCUXpresso SDK
- MCUXpresso IDE
- MCUXpresso Config Tools
- Kinetis Design Studio
- Kinetis Software Development Kit
- LPCXpresso IDE
- LPCXpresso IDE FAQs
- MCU Bootloader
- MCUXpresso Secure Provisioning Tool
-
- CodeWarrior
- MQX Software Solutions
- Model-Based Design Toolbox (MBDT)
-
- Topics
- Mobile Robotics - Drones and Rovers
- NXP Training Content
- University Programs
-
- Home
- :
- About peterdufault
About peterdufault
peterdufault
Contributor III
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
Activity Feed
- Posted Re: Are the eTPU application note APIs misleading about eTPU link channels? on MPC5xxx. 05-23-2015 08:51 AM
- Posted Are the eTPU application note APIs misleading about eTPU link channels? on MPC5xxx. 05-23-2015 08:48 AM
- Posted Re: Could someone clarify 3 to 2 phase conversion in Analog Sensing for AC Motors eTPU function? on Other NXP Products. 07-01-2014 01:24 PM
- Posted Re: Could someone clarify 3 to 2 phase conversion in Analog Sensing for AC Motors eTPU function? on Other NXP Products. 07-01-2014 04:53 AM
- Posted Could someone clarify 3 to 2 phase conversion in Analog Sensing for AC Motors eTPU function? on Other NXP Products. 06-30-2014 10:08 AM
- Posted Re: Problems with theta calculation in PMSM Vector Control function on Other NXP Products. 06-27-2014 09:04 AM
- Posted Re: Problems with theta calculation in PMSM Vector Control function on Other NXP Products. 06-27-2014 08:51 AM
- Posted Problems with theta calculation in PMSM Vector Control function on Other NXP Products. 06-27-2014 07:56 AM
- Posted Re: Does etpu_app_pmsmesvc3 Permanent Magnet Synchronous Motor Vector Control (AN3206) work? on MPC5xxx. 06-26-2014 01:35 PM
- Posted Re: In AN3206 "PMSM vector control..." how can u_ab be {0, 0} and u_dq {non_zero, 0} in align_start state? on Other NXP Products. 06-26-2014 06:16 AM
- Posted In AN3206 "PMSM vector control..." how can u_ab be {0, 0} and u_dq {non_zero, 0} in align_start state? on Other NXP Products. 06-25-2014 10:54 AM
- Posted Re: Setting up scaling etc. for PMSM vector control on eTPU with customer motor on Other NXP Products. 06-24-2014 02:19 PM
- Posted Re: Setting up scaling etc. for PMSM vector control on eTPU with customer motor on Other NXP Products. 06-24-2014 10:18 AM
- Posted Setting up scaling etc. for PMSM vector control on eTPU with customer motor on Other NXP Products. 06-24-2014 06:57 AM
- Posted Can I use eMIOS quadrature decoder and Hall effect Speed Controller with PMSM Vector Control? on MPC5xxx. 02-08-2014 06:00 AM
- Posted Re: Does etpu_app_pmsmesvc3 Permanent Magnet Synchronous Motor Vector Control (AN3206) work? on MPC5xxx. 02-08-2014 05:28 AM
- Posted Does etpu_app_pmsmesvc3 Permanent Magnet Synchronous Motor Vector Control (AN3206) work? on MPC5xxx. 02-07-2014 05:02 AM
- Posted Re: Where is source for AN3206 "Permanent Magnet Synchronous Vector Control..."? on MPC5xxx. 01-24-2014 05:23 AM
- Posted Where is source for AN3206 "Permanent Magnet Synchronous Vector Control..."? on MPC5xxx. 01-20-2014 07:08 AM
Latest posts by peterdufault
| Subject | Views | Posted |
|---|---|---|
| 224 | 05-23-2015 08:51 AM | |
| 330 | 05-23-2015 08:48 AM | |
| 170 | 07-01-2014 01:24 PM | |
| 170 | 07-01-2014 04:53 AM | |
| 274 | 06-30-2014 10:08 AM |
Community Statistics
| Posts | 19 |
| Solutions | 2 |
| Kudos given | 0 |
| Kudos received | 0 |
| Member Since | 01-20-2014 |
Contact Me
| Online Status |
Offline
|
| Date Last Visited |
08-29-2020
02:08 AM
|