S32G399A-RDB3 QNX PFE Driver Problems

Seneca · ‎06-23-2026

Greetings,

we try to get PFE running on a S32G399A-RDB3 board with QNX. As far as I can tell, this is a valid combination:

BSP 37.0
PFE-FW_S32G_1.7.0
PFE-DRV-S32G_A53_QNX_1.4.0

It ends with a no carrier error on all network interfaces. Plugging the cable into different ethernet ports changes nothing.

It used to work with gmac0.

Any ideas?

io pkt call:

io-pkt-v6-hc -p tcpip -d pfe-2 pfe0_mac=000a0b0c0d66,pfe1_mac=001a1b1c1d66,pfe2_mac=002a2b2c2d66,class_fw=/proc/boot/s32g_pfe_class.fw,no_reset,mode0=sgmii,phy0=0,mode1=sgmii,phy1=1

Uboot parameters:

Uboot is the same as from the Linux sdcard image with modified parmeters for qnx boot.

setenv hwconfig "pcie0:mode=rc,clock=ext;pcie1:mode=sgmii,clock=ext,fmhz=125,xpcs_mode=2G5"
setenv pfeng_mode 'enable,sgmii,sgmii,rgmii'
setenv s32cc_gmac_mode disable
setenv pfeng enable; s32ccgmac disable; s32ccgmac enable;
setenv boot_qnx_atf 'mmc dev 0; fatload mmc 0:1 0x83e00000 s32g399a-rdb3.dtb; pfeng enable; s32ccgmac disable; s32ccgmac enable; fatload mmc 0:1 0x80080000 ifs-s32g399a-rdb.ui; bootm 0x80080000 - 0x83E00000'
setenv bootcmd 'run boot_qnx_atf'
saveenv

Log:

U-Boot 2020.04+g156b168010 (Jun 09 2023 - 10:14:25 +0000)

CPU: NXP S32G399A rev. 1.1

Model: NXP S32G399A-RDB3

DRAM: 3.5 GiB

MMC: FSL_SDHC: 0

Loading Environment from MMC... OK

Configuring PCIe0 as RootComplex

PCIe0: Failed to get link up

PCI: Failed autoconfig bar 1c

In: serial@401c8000

Out: serial@401c8000

Err: serial@401c8000

Board revision: RDB3 Revision F

Net: EQOS phy: rgmii @ 1

Warning: eth_eqos (eth0) using random MAC address - 26:e4:e6:43:15:ad

eth0: eth_eqosFailed to get speed of XPCS for emac1_xpcs PFE: emac0: sgmii emac1: sgmii emac2: rgmii

, eth1: eth_pfeng

Hit any key to stop autoboot: 3 2 1 0

switch to partitions #0, OK

mmc0 is current device

50640 bytes read in 17 ms (2.8 MiB/s)

11948752 bytes read in 540 ms (21.1 MiB/s)

## Booting kernel from Legacy Image at 80080000 ...

Image Name:

Image Type: AArch64 Linux Kernel Image (uncompressed)

Data Size: 11948688 Bytes = 11.4 MiB

Load Address: 80080000

Entry Point: 80080000

Verifying Checksum ... OK

## Flattened Device Tree blob at 83e00000

Booting using the fdt blob at 0x83e00000

Loading Kernel Image

Using Device Tree in place at 0000000083e00000, end 0000000083e0f5cf

fixup: pfe0 set to 00:01:be:be:ef:11

fixup: pfe1 set to 00:01:be:be:ef:22

fixup: pfe1: update phy addr to 0x8

fixup: pfe2 set to 00:01:be:be:ef:33

Starting kernel ...

Reserving RAM region for PFE driver on EVB/RDB

Done.

ClockCycles samples:

0 43600679

1 43600679

2 43600678

3 43600679

4 43600678

5 43600678

6 43600678

7 43600679

All ClockCycles offsets within tolerance

Welcome to QNX Neutrino 7.1.0 on the NXP S32G399A RDB Board!!

Starting watchdog...

Starting serial driver ...

Starting Networking driver (/dev/socket)...

Process 4107 (ifconfig) exited status=0.

Process 10 (sh) exited status=0.

Process 9 (dhclient) exited status=0.

cp: Can't open source file. (/proc/boot/libfci_cli)

Process 20489 (cp) exited status=1.

Starting SPI driver (/dev/spi0,1,2,3,4,5)...

Starting I2C 0/1/2/3/4 driver (/dev/i2c0,1,2,3,4)...

Starting USDHC0 memory card driver...

[00] SIM="SDMMC" HBA="imx"

[00,0,0] type=00 ver=05 resp=00 SDMMC:

Process 24596 (chkqnx6fs) exited status=0.

Process 28692 (mount) exited status=0.

Starting QSPI Flash driver...

Starting USB host driver (/dev/usb/*)

Detected QSPI Flash: Macronix MX25UW512, JEDEC 0xC2 - 0x813A, Size: 0x4000000

Launching devb-umass for /dev/usb/* ...

#

Process 36891 (sleep) exited status=0.

sh: /var/cetitec2/startup.sh: No such file or directory

Process 45081 (sh) terminated signo=0 code=0 by process 0 value=0.

slog2info

Jan 01 00:00:00.023 random.4 low* 0 qcrypto: loading configuration file '/etc/qcrypto.conf' [qcrypto_common.c(190)]

Jan 01 00:00:00.024 random.4..0 slog* 700 Random is using the Fortuna PRNG

Jan 01 00:00:00.031 random.4 low 0 qcrypto: 'openssl' plugin loaded [qcrypto_plugins.c(354)]

Jan 01 00:00:00.031 random.4..0 slog 700 Selecting timer as an entropy source

Jan 01 00:00:00.032 random.4..0 slog 700 Registered path names

Jan 01 00:00:00.032 random.4..0 slog 700 random: starting resmgr

Jan 01 00:00:00.032 random.4..0 slog 700 random: Daemonizing the process

Jan 01 00:00:00.042 devc_serlinflexd.7 slog* 0 serlinflexd_interrupt_attach: Attaching to interrupt 114

Jan 01 00:00:00.047 iopkt.8 main_buffer* 0 tcpip starting

Jan 01 00:00:00.047 iopkt.8 main_buffer 0 smmu support is disabled

Jan 01 00:00:00.049 iopkt.8 main_buffer 0 initializing IPsec...

Jan 01 00:00:00.049 iopkt.8 main_buffer 0 done

Jan 01 00:00:00.049 iopkt.8 main_buffer 0 IPsec: Initialized Security Association Processing.

Jan 01 00:00:00.051 iopkt.8 main_buffer 0 devnp-pfe-2.so pfe0_mac=000a0b0c0d66,pfe1_mac=001a1b1c1d66,pfe2_mac=002a2b2c2d66,class_fw=/proc/boot/s32g_pfe_class.fw,pfe0_mode=sgmii,pfe0_phy=0,pfe1_mode=sgmii,pfe1_phy=1

Jan 01 00:00:00.052 io_pkt_v6_hc.8 slog* 0 INF[src/pfe_drv.c:1377]: VERSION INFO

Driver version: 1.4.0

Driver commit hash: 2f3265a49ac18f94ba5e48254c8f870fe7bfc511

PFE_CFG_MULTI_INSTANCE_SUPPORT: 0

PFE_CFG_LOCAL_IF: 6

PFE_CFG_MASTER_IF: 6

PFE_CFG_SC_HIF: 1

PFE_CFG_HIF_RING_LENGTH: 256

PFE_CFG_PFE0_PROMISC: 1

PFE_CFG_PFE1_PROMISC: 1

PFE_CFG_PFE2_PROMISC: 1

Jan 01 00:00:00.052 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1384]: --- Safe IRQ enabled. No InterrupAttach() or InterruptAttach_r() allowed.

Jan 01 00:00:00.052 io_pkt_v6_hc.8 slog 0 INF[src/pfe_fw.c:83]: 42792 bytes read

Jan 01 00:00:00.053 io_pkt_v6_hc.8 slog 0 INF[src/pfe_fw.c:89]: Loaded firmware file: /proc/boot/s32g_pfe_class.fw

Jan 01 00:00:00.053 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1477]: MII mode configuration for pfe0/EMAC0 not found. Using SGMII.

Jan 01 00:00:00.053 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1477]: MII mode configuration for pfe1/EMAC1 not found. Using SGMII.

Jan 01 00:00:00.053 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1477]: MII mode configuration for pfe2/EMAC2 not found. Using RGMII.

Jan 01 00:00:00.053 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1495]: Issuing PFE peripheral reset...

Jan 01 00:00:00.274 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1496]: PFE reset OK.

Jan 01 00:00:00.274 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:3519]: PFE CBUS p0x46000000 mapped @ v0x38f2e23000

Jan 01 00:00:00.274 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:3524]: HW version 0x101

Jan 01 00:00:00.274 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hw_feature.c:95]: Silicon S32G3

Jan 01 00:00:00.274 io_pkt_v6_hc.8 slog 0 WRN[hw/s32g/pfe_platform_master.c:3536]: Fail-Stop mode disabled

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2687]: PFE_ERRORS:Parity instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2702]: PFE_ERRORS:Watchdog instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2718]: PFE_ERRORS:Bus Error instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2731]: PFE_ERRORS:FW Fail Stop instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2744]: PFE_ERRORS:Host Fail Stop instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2757]: PFE_ERRORS:Fail Stop instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2770]: PFE_ERRORS:ECC Err instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:1766]: BMU1 buffer base: p0xc0000000

Jan 01 00:00:00.277 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:1810]: BMU2 buffer base: p0x83000000 (0x200000 bytes)

Jan 01 00:00:00.279 io_pkt_v6_hc.8 slog 0 INF[src/oal_irq_qnx.c:117]: PFE BMU IRQ Worker started (IRQ ID: 226)

Jan 01 00:00:00.279 io_pkt_v6_hc.8 slog 0 WRN[hw/s32g/pfe_platform_master.c:2194]: The option 'g2_ordered_class_writes' is disabled.

Jan 01 00:00:00.279 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_bmu_csr.c:96]: BMU_EMPTY_INT (BMU @ p0x88000). Pool ready.

Jan 01 00:00:00.279 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_bmu_csr.c:96]: BMU_EMPTY_INT (BMU @ p0x8c000). Pool ready.

Jan 01 00:00:00.281 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2239]: Firmware .elf detected

Jan 01 00:00:00.281 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2248]: Uploading CLASS firmware

Jan 01 00:00:00.281 io_pkt_v6_hc.8 slog 0 INF[src/pfe_pe.c:609]: Selected FW loading OPs to load 8 PEs in parallel

Jan 01 00:00:00.285 io_pkt_v6_hc.8 slog 0 INF[src/pfe_pe.c:1945]: pfe_ct.h file version"92367c0e25f21f49217a9b08168ad2c8"

Jan 01 00:00:00.288 io_pkt_v6_hc.8 slog 0 INF[src/pfe_pe.c:2422]: [FW VERSION] 1.7.0, Build: Jun 2 2023, 13:48:57 (nogitaaa), ID: 0x31454650

Jan 01 00:00:00.406 io_pkt_v6_hc.8 slog 0 WRN[hw/s32g/pfe_platform_master.c:2312]: VLAN ID incorrect or not set. Using default VLAN ID = 0x01.

Jan 01 00:00:00.406 io_pkt_v6_hc.8 slog 0 WRN[hw/s32g/pfe_platform_master.c:2318]: VLAN stats size incorrect or not set. Using default VLAN stats size = 20.

Jan 01 00:00:00.406 io_pkt_v6_hc.8 slog 0 INF[src/pfe_l2br.c:1181]: Software vlan hash table @ p0x20001228

Jan 01 00:00:00.406 io_pkt_v6_hc.8 slog 0 INF[src/pfe_l2br.c:1286]: Fall-back bridge domain @ 0x20000a7c (class)

Jan 01 00:00:00.406 io_pkt_v6_hc.8 slog 0 INF[src/pfe_l2br.c:1287]: Default bridge domain @ 0x20000a74 (class)

Jan 01 00:00:00.406 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2412]: Routing table created, Hash Table @ p0x80014000, Pool @ p0x8001c000 (65536 bytes)

Jan 01 00:00:00.407 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_chnl.c:1997]: Initializing RX buffer pool. Depth: 256; Buffer Size: 2048; Cache Line Size: 64

Jan 01 00:00:00.408 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_chnl.c:1997]: Initializing RX buffer pool. Depth: 256; Buffer Size: 2048; Cache Line Size: 64

Jan 01 00:00:00.409 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_chnl.c:1997]: Initializing RX buffer pool. Depth: 256; Buffer Size: 2048; Cache Line Size: 64

Jan 01 00:00:00.508 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:3705]: Feature err051211_workaround: DISABLED

Jan 01 00:00:00.509 iopkt.8 main_buffer 0 pfe0

Jan 01 00:00:00.509 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2152]: pfe0: Using PHY mode: MDIO=0, ADDR=0, CLAUSE=0, RESET=0

Jan 01 00:00:00.509 io_pkt_v6_hc.8 slog 0 INF[src/oal_irq_qnx.c:117]: PFE HIF0 IRQ Worker started (IRQ ID: 222)

Jan 01 00:00:00.509 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1795]: Adding 00:0a:0b:0c:0d:66 to pfe0

Jan 01 00:00:00.511 iopkt.8 main_buffer 0 pfe1

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2298]: Speed/duplex configuration for pfe0 not found. Using 1 Gbps/full-duplex.

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_drv_sc.c:336]: Attempt to register HIF client: 0

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_drv_sc.c:1189]: HIF driver started

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2363]: New PFE device: 0, ID: 0

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2152]: pfe1: Using PHY mode: MDIO=1, ADDR=0, CLAUSE=0, RESET=0

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/oal_irq_qnx.c:117]: PFE HIF1 IRQ Worker started (IRQ ID: 223)

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1795]: Adding 00:1a:1b:1c:1d:66 to pfe1

Jan 01 00:00:00.513 iopkt.8 main_buffer 0 pfe2

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2298]: Speed/duplex configuration for pfe1 not found. Using 1 Gbps/full-duplex.

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_drv_sc.c:336]: Attempt to register HIF client: 1

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_drv_sc.c:1189]: HIF driver started

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2363]: New PFE device: 1, ID: 2

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2145]: pfe2: Using static PHY mode, RESET=0

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/oal_irq_qnx.c:117]: PFE HIF2 IRQ Worker started (IRQ ID: 224)

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1795]: Adding 00:2a:2b:2c:2d:66 to pfe2

Jan 01 00:00:00.515 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2298]: Speed/duplex configuration for pfe2 not found. Using 1 Gbps/full-duplex.

Jan 01 00:00:00.515 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_drv_sc.c:336]: Attempt to register HIF client: 2

Jan 01 00:00:00.515 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_drv_sc.c:1189]: HIF driver started

Jan 01 00:00:00.515 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2363]: New PFE device: 2, ID: 4

Jan 01 00:00:00.530 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2702]: Adding 00:0a:0b:0c:0d:66 to pfe0

Jan 01 00:00:00.530 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2707]: Unable to assign MAC address 00:0a:0b:0c:0d:66 to the pfe0

Jan 01 00:00:00.530 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2663]: pfe0: Disabling promiscuous mode

Jan 01 00:00:00.538 io_pkt_v6_hc.8 slog 0 INF[src/pfe_mdio.c:427]: pfe0: PHY @ bus 0 addr 0 not found. Switching to static mode.

Jan 01 00:00:00.538 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2829]: EMAC speed change for SGMII is currently not supported.

Jan 01 00:00:00.538 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:ff:0c:0d:66 to emac0

Jan 01 00:00:00.540 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2663]: pfe0: Disabling promiscuous mode

Jan 01 00:00:00.540 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:00:00:00:01 to emac0

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:ff:0c:0d:66 to emac0

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2450]: unable to add 33:33:ff:0c:0d:66 into emac0: 17

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2663]: pfe0: Disabling promiscuous mode

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:00:00:00:01 to emac0

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2450]: unable to add 33:33:00:00:00:01 into emac0: 17

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:ff:0c:0d:66 to emac0

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2450]: unable to add 33:33:ff:0c:0d:66 into emac0: 17

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2663]: pfe0: Disabling promiscuous mode

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2829]: EMAC speed change for SGMII is currently not supported.

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 01:00:5e:00:00:01 to emac0

Jan 01 00:00:00.544 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:00:00:00:01 to emac0

Jan 01 00:00:00.544 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2450]: unable to add 33:33:00:00:00:01 into emac0: 17

Jan 01 00:00:00.544 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:ff:0c:0d:66 to emac0

Jan 01 00:00:00.544 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2450]: unable to add 33:33:ff:0c:0d:66 into emac0: 17

Jan 01 00:00:00.544 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2663]: pfe0: Disabling promiscuous mode

Jan 01 00:00:00.554 spi_master.24585 normal* 0 Starting spi-master resource manager

Jan 01 00:00:00.558 spi_master.24587 normal* 0 Starting spi-master resource manager

Jan 01 00:00:00.561 spi_master.24588 normal* 0 Starting spi-master resource manager

Jan 01 00:00:00.565 spi_master.24589 normal* 0 Starting spi-master resource manager

Jan 01 00:00:00.582 devb_sdmmc_mx8x.24595 slog* 1800 devb-sdmmc-mx8x 1.00A (Jun 23 2026 09:45:48)

Jan 01 00:00:00.583 devb_sdmmc_mx8x.24595 slog 0 libcam.so (Jun 22 2020 21:33:15) bver 7010003

Jan 01 00:00:00.594 devb_sdmmc_mx8x.24595 slog 1800 sdio_cd: insertion path 0, cd state 0x1

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 SD CID:

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 MID 0x27, OID 0x5048, PNM SD32G

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 PRV 0x62, PSN 0x6c62d132, MDT 4-2023

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 SD CSD:

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 CSD_STRUCTURE 1, SPEC_VERS 0, CCC 0x5b5

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 TAAC 14, NSAC 0, TRAN_SPEED 50

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 C_SIZE 59023, C_SIZE_MULT 0

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 READ_BL_LEN 9, WRITE_BL_LEN 9

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 ERASE GRP_SIZE 0, GRP_MULT 0, SIZE 127

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 blksz 512, sectors 60440576, dtr 25000000

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 SD SW CAPS:

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 bus mode 0x3, cmd sys 0x1

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 drv type 0x1, curr limit 0x1

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 dtr 50000000

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 CFG: Timing HS, DTR 50000000, Bus Width 4 bit

Jan 01 00:00:00.645 devb_sdmmc_mx8x.24595 slog 100 cam-disk.so (Jun 22 2020 21:33:17)

Jan 01 00:00:00.647 devb_sdmmc_mx8x.24595 slog 0 scsi_interpret_sense (sdmmc ptl-0:0:0): cam_status=c4, scsi_status=2, flag=00000040, vuflag=0008, cmd=1a, error=70, sense=5, asc=24, ascq=0

Jan 01 00:00:00.647 devb_sdmmc_mx8x.24595 slog 0 scsi_interpret_sense (sdmmc ptl-0:0:0): cam_status=c4, scsi_status=2, flag=00000040, vuflag=0008, cmd=5a, error=70, sense=5, asc=24, ascq=0

Jan 01 00:00:01.827 devb_sdmmc_mx8x.24595 slog 1000 fs-qnx6: Allocation strategy 0

Jan 01 00:00:01.827 devb_sdmmc_mx8x.24595 slog 1000 fs-qnx6: Use btree directory 0

Jan 01 00:00:01.828 devb_sdmmc_mx8x.24595 slog 1000 fs-qnx6: fs-qnx6: trim (0,1048576,2) was not requested, and is NOT supported

Jan 01 00:00:01.833 io_usb_otg.36885 slog* 0 main(453)[tid:1]: io-usb-otg (Jun 13 2020 20:10:17) args: -d hcd-ehci-mx28 ioport=0x44064100,irq=243,ulpi,no_stream,verbose=5

Jan 01 00:00:01.835 devf_qspi_s32g.36884 slog* 0 (devf t1::f3s_qspi_ident:73) Page size: 256

Jan 01 00:00:01.835 devf_qspi_s32g.36884 slog 0 (devf t1::f3s_qspi_ident:74) Total chip size: 0x4000000, Unit size: 0x10000

Jan 01 00:00:01.839 io_usb_otg.36885 slog 0 ehci_init: Initialiaing with sever version: 2

Jan 01 00:00:01.839 io_usb_otg.36885 slog 0 ehci_controller_init(4303): devu-hcd-ehci-mx28.so (Apr 19 2024 13:44:54): args ulpi,no_stream,verbose=5

Jan 01 00:00:01.840 io_usb_otg.36885 slog 8 usb_enum_port(94)[tid:1]: busno 0, parent -1, port 0, High speed

Jan 01 00:00:01.840 io_usb_otg.36885 slog 11 usb_client_descriptor_get(198)[tid:1]: (type 1, index 0, length

Jan 01 00:00:01.840 io_usb_otg.36885 slog 12 usb_device_set_address(245)[tid:1]: b:0 devno 0

Jan 01 00:00:01.840 io_usb_otg.36885 slog 11 usb_client_descriptor_get(198)[tid:1]: (type 1, index 0, length 18)

Jan 01 00:00:01.841 io_usb_otg.36885 slog 11 usb_client_descriptor_get(198)[tid:1]: (type 2, index 0, length 9)

Jan 01 00:00:01.841 io_usb_otg.36885 slog 11 usb_client_descriptor_get(198)[tid:1]: (type 2, index 0, length 25)

Jan 01 00:00:01.841 io_usb_otg.36885 slog 8 usb_enum_port(141)[tid:1]: vid 0x0000, did 0x0000 enumerated(busno 0, devno 0:0)

Jan 01 00:00:01.841 io_usb_otg.36885 slog 11 hub_state_inserted(569)[tid:1]: bdentry 0, dentry 0 0

Jan 01 00:00:01.841 io_usb_otg.36885 slog 13 hub_configuration_enable(263)[tid:1]: 1

Jan 01 00:00:01.943 io_usb_otg.36885 slog 0 usbh_timeout_init(203)[tid:1]: Complete

Jan 01 00:00:01.954 io_usb_otg.36885 slog 0 read_vid_pid: ULPI VID 0x0424 PID 0x0009

Jan 01 00:00:01.954 io_usb_otg.36885 slog 0 s32g_phy_set_vbus: set_vbus off

Jan 01 00:00:01.968 io_usb_otg.36885 slog 0 s32g_phy_set_vbus: set_vbus on

Jan 01 00:00:01.979 io_usb_otg.36885 slog 0 ehci_get_port_status(3568 0x44064100): port=0, tpstatus 10100 e_pstatus 8c001000

Jan 01 00:00:01.979 io_usb_otg.36885 slog 8 usb_enum_port_extract(172)[tid:7]: (busno 0, pdevno 0, portno 1)

Jan 01 00:00:01.979 io_usb_otg.36885 slog 8 usb_enum_port_extract(192)[tid:7]: status (2)

Jan 01 00:00:01.983 devb_umass.36886 slog* 900 devb-umass 1.00A (Jun 22 2020 21:33:41)

Jan 01 00:00:01.984 devb_umass.36886 slog 0 libcam.so (Jun 22 2020 21:33:15) bver 7010003

Jan 01 00:00:01.985 io_usb_otg.36885 slog 0 usbdi_client_connect(58)[tid:5]: pid 36886 proc=proc/boot/devb-umass usbdi_client 32eebb9a80

Jan 01 00:00:01.986 io_usb_otg.36885 slog 0 usbdi_resmgr_connect(310)[tid:5]: usbdi_resmgr_connect: pid 36886 usbdi_client 32eebb9a80

Jan 01 00:00:01.986 devb_umass.36886 slog 0 usbdi debug path /pps/usb/debug/ doesn't exist

Process 49177 (slog2info) exited status=0.

# ifconfig

lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33136

inet 127.0.0.1 netmask 0xff000000

inet6 ::1 prefixlen 128

inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1

pfe0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500

capabilities=1f<IP4CSUM,TCP4CSUM,UDP4CSUM,TCP6CSUM,UDP6CSUM>

enabled=0

address: 00:0a:0b:0c:0d:66

media: Ethernet none (1000baseT full-duplex)

status: active

inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255

inet6 fe80::20a:bff:fe0c:d66%pfe0 prefixlen 64 scopeid 0x11

pfe1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500

capabilities=1f<IP4CSUM,TCP4CSUM,UDP4CSUM,TCP6CSUM,UDP6CSUM>

enabled=0

address: 00:1a:1b:1c:1d:66

media: Ethernet none (1000baseT full-duplex)

status: no carrier

pfe2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500

capabilities=1f<IP4CSUM,TCP4CSUM,UDP4CSUM,TCP6CSUM,UDP6CSUM>

enabled=0

address: 00:2a:2b:2c:2d:66

media: Ethernet none (1000baseT full-duplex)

status: no carrier

Process 57369 (ifconfig) exited status=0.

#

Seneca

Another thing. Will this uboot line recommended in the integration manual:

hwconfig "serdes0:mode=pcie,clock=ext;pcie0:mode=rc;serdes1:mode=xpcs0&xpcs1,clock=ext,fmhz=125;xpcs1_0:speed=2G5;xpcs1_1:speed=1G"

Really enable gmac0, pfe0 and pfe2 as individual interfaces or only two of them?

chenyin_h

Hello, @Seneca

Thanks for your reply.

1. For the hwconfig you mentioned, when using them on RDB3, the 3 MACs could all be used.

2. For the error log you shared, sorry that we do not commonly support QNX commands directly, form my personal experience, it may caused by the command used itself, I suggest re-checking syntax of commands based on the QNX document.

3. Under QNX, there are some limitation for the PFE driver, auto-negotiation is not supported, so you may make sure that the two sides are running with the same speed.

BR

Chenyin

Seneca

Greetings,

I recorded the network adapter state of a LInux Laptop that successfully connects to the TC387 media converter (which should be in 100T1 master mode). Can you tell me if pfe2 can drive this mode?

*-network:1

description: Ethernet interface

physical id: e

bus info: usb@2:4

logical name: enx00e04c680383

serial: 00:e0:4c:68:03:83

size: 100Mbit/s

capacity: 1Gbit/s

capabilities: ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation

configuration: autonegotiation=on broadcast=yes driver=r8152 driverversion=v1.12.13 duplex=full firmware=rtl8153b-2 v2 04/27/23 ip=192.168.10.102 link=yes multicast=yes port=MII speed=100Mbit/s

NIC statistics:

tx_packets: 60

rx_packets: 3

tx_errors: 0

rx_errors: 0

rx_missed: 0

align_errors: 0

tx_single_collisions: 0

tx_multi_collisions: 0

rx_unicast: 3

rx_broadcast: 0

rx_multicast: 0

tx_aborted: 0

tx_underrun: 0

enx00e04c680383: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500

inet 192.168.10.102 netmask 255.255.255.0 broadcast 192.168.10.255

inet6 fe80::9165:ed06:804a:54c0 prefixlen 64 scopeid 0x20<link>

ether 00:e0:4c:68:03:83 txqueuelen 1000 (Ethernet)

RX packets 0 bytes 0 (0.0 B)

RX errors 0 dropped 0 overruns 0 frame 0

TX packets 0 bytes 0 (0.0 B)

TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

Settings for enx00e04c680383:

Supported ports: [ TP MII ]

Supported link modes: 10baseT/Half 10baseT/Full

100baseT/Half 100baseT/Full

1000baseT/Half 1000baseT/Full

Supported pause frame use: No

Supports auto-negotiation: Yes

Supported FEC modes: Not reported

Advertised link modes: 10baseT/Half 10baseT/Full

100baseT/Half 100baseT/Full

1000baseT/Full

Advertised pause frame use: No

Advertised auto-negotiation: Yes

Advertised FEC modes: Not reported

Link partner advertised link modes: 10baseT/Half 10baseT/Full

100baseT/Half 100baseT/Full

Link partner advertised pause frame use: No

Link partner advertised auto-negotiation: Yes

Link partner advertised FEC modes: Not reported

Speed: 100Mb/s

Duplex: Full

Auto-negotiation: on

Port: MII

PHYAD: 32

Transceiver: internal

Supports Wake-on: pumbg

Wake-on: g

Current message level: 0x00007fff (32767)

drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol

Link detected: yes

chenyin_h

Hello, @Seneca

Thanks for your post.

1. I can confirm that the PFE2 port on RDB3 could work correctly with connection to 100T1 network via a 100base-TX<->100base-T1 converter under Linux BSP provisioned by NXP.

2. You may try the following command for a test: io-pkt-v6-hc -p tcpip -d pfe2_link=100-1-2

But I am not very sure for these settings on QNX since it is beyond our S32G community supporting scope, sorry for your inconvenience.

BR

Chenyin

Seneca

Greetings,

I tried setting the correct speed on QNX with something like

ifconfig pfe2 media 100baseTX mediaopt full-duplex

but it wasn't enough. Do I have to do something else, maybe even in uboot parameters?

Regards

Seneca

Greetings,

after more research it seem that pfe_mac2 in particular has problems with our 100T1 ethernet adapters. Connecting a Linux Laptop with USB ethernet works fine though.

Do you know if pfe_mac2 can connect to this adapter type correctly and if I have to do something special to make it work?

Regards

Seneca

Ok, so I should be able to use, from the three stacked ports, left port as pfe0 and top center as pfe2 I presume. Bottom center for gmac0.

Now, I try to start the interfaces in bridge mode using the following io pkt syntax (note the bridge parameter behind tcp ip):

io-pkt-v6-hc -p tcpip bridge pkt_typed_mem=pfe_ddr -d dwceqos-s32g mac=`genmac-random -m`,ptp_off,verbose=5 -d /proc/boot/devnp-pfe-2.so pfe0_mac=000a0b0c0d66,pfe1_mac=001a1b1c1d66,pfe2_mac=002a2b2c2d66,class_fw=/proc/boot/s32g_pfe_class.fw,util_fw=/proc/boot/s32g_pfe_util.fw
ifconfig dwc0 192.168.10.100 up
ifconfig pfe0 0.0.0.0 up
ifconfig pfe2 0.0.0.0 up
ifconfig bridge0 create
ifconfig bridge0 add dwc0 add pfe0 add pfe2 up

This will result in lots of memory errors in slog2info

Jan 01 00:04:37.485 io_pkt_v6_hc.159753 slog 0 ERR[src/pfe_drv.c:2996]: (DRIVER) event 1 - Driver runtime error: Mbuf addr out of 32bit. Start @ p0x8df239b58 end @ p0x8df239b82

Jan 01 00:04:38.485 io_pkt_v6_hc.159753 slog 0 ERR[src/pfe_drv.c:2996]: (DRIVER) event 1 - Driver runtime error: Mbuf addr out of 32bit. Start @ p0x8df239558 end @ p0x8df239582

Jan 01 00:04:39.451 io_pkt_v6_hc.159753 slog 0 ERR[src/pfe_drv.c:2996]: (DRIVER) event 1 - Driver runtime error: Mbuf addr out of 32bit. Start @ p0x8df239b58 end @ p0x8df239b82

Is bridge parameter correct in io-pkt-v6-hc call?

Also, I use this allocation from the driver integration manual for both gmac0 and pfe as can be seen in the io-pkt-v6-hc call. Is that a problem?

kprintf("Reserving RAM region for PFE driver on EVB/RDB\n");
as_add_containing(0x80000000,0x80000000 + 0x4000000 - 1,AS_ATTR_RAM, "pfe_ddr","ram");

Seneca

Greetings,

when I connect the TC387 to my Linux desktop there are lots of arp/icmp messages produced immediately. The same when I connect my S32G pfe2 port to the Linux desktop. But when I connect the TC387 to the S32G pfe2 port I get not arp or icmp messages at all.

For which error messages should I look?

Regards

Seneca

Greetings,

can you tell me if 192.168.0.200 listens to broadcast calls or something like that?

Regards

chenyin_h

Hello, @Seneca

Thanks for your reply.

This IP could receive the broadcast packets from linked devices.

BR

Chenyin

Seneca

Greetings,

init_serdes();

has been commented out from the s32g399a-rdb main.c.

Regards

Seneca

Greetings,

I intend to try the following combination:

BSP 33

PFE Driver 1.2.0

PFE FW 1.3.0

Is this officially supported?

Regards

chenyin_h

Hello. @Seneca

Thanks for your reply.

1. For the combination, I suggest referencing the documents included in the QNX PFE drivers directly, which included the recommended/tested combination.

Other combination may or may not work, you may test it accordingly if indeed needed.

2. From the available information, for QNX PFE drive 1.2, the supported PFE FW is 1.2 with BSP30 used for test

BR

Chenyin