S32G399A-RDB3 QNX PFE Driver Problems

Seneca

Greetings,

we try to get PFE running on a S32G399A-RDB3 board with QNX. As far as I can tell, this is a valid combination:

BSP 37.0
PFE-FW_S32G_1.7.0
PFE-DRV-S32G_A53_QNX_1.4.0

It ends with a no carrier error on all network interfaces. Plugging the cable into different ethernet ports changes nothing.

It used to work with gmac0.

Any ideas?

io pkt call:

io-pkt-v6-hc -p tcpip -d pfe-2 pfe0_mac=000a0b0c0d66,pfe1_mac=001a1b1c1d66,pfe2_mac=002a2b2c2d66,class_fw=/proc/boot/s32g_pfe_class.fw,no_reset,mode0=sgmii,phy0=0,mode1=sgmii,phy1=1

Uboot parameters:

Uboot is the same as from the Linux sdcard image with modified parmeters for qnx boot.

setenv hwconfig "pcie0:mode=rc,clock=ext;pcie1:mode=sgmii,clock=ext,fmhz=125,xpcs_mode=2G5"
setenv pfeng_mode 'enable,sgmii,sgmii,rgmii'
setenv s32cc_gmac_mode disable
setenv pfeng enable; s32ccgmac disable; s32ccgmac enable;
setenv boot_qnx_atf 'mmc dev 0; fatload mmc 0:1 0x83e00000 s32g399a-rdb3.dtb; pfeng enable; s32ccgmac disable; s32ccgmac enable; fatload mmc 0:1 0x80080000 ifs-s32g399a-rdb.ui; bootm 0x80080000 - 0x83E00000'
setenv bootcmd 'run boot_qnx_atf'
saveenv

Log:

U-Boot 2020.04+g156b168010 (Jun 09 2023 - 10:14:25 +0000)

CPU: NXP S32G399A rev. 1.1

Model: NXP S32G399A-RDB3

DRAM: 3.5 GiB

MMC: FSL_SDHC: 0

Loading Environment from MMC... OK

Configuring PCIe0 as RootComplex

PCIe0: Failed to get link up

PCI: Failed autoconfig bar 1c

In: serial@401c8000

Out: serial@401c8000

Err: serial@401c8000

Board revision: RDB3 Revision F

Net: EQOS phy: rgmii @ 1

Warning: eth_eqos (eth0) using random MAC address - 26:e4:e6:43:15:ad

eth0: eth_eqosFailed to get speed of XPCS for emac1_xpcs PFE: emac0: sgmii emac1: sgmii emac2: rgmii

, eth1: eth_pfeng

Hit any key to stop autoboot: 3 2 1 0

switch to partitions #0, OK

mmc0 is current device

50640 bytes read in 17 ms (2.8 MiB/s)

11948752 bytes read in 540 ms (21.1 MiB/s)

## Booting kernel from Legacy Image at 80080000 ...

Image Name:

Image Type: AArch64 Linux Kernel Image (uncompressed)

Data Size: 11948688 Bytes = 11.4 MiB

Load Address: 80080000

Entry Point: 80080000

Verifying Checksum ... OK

## Flattened Device Tree blob at 83e00000

Booting using the fdt blob at 0x83e00000

Loading Kernel Image

Using Device Tree in place at 0000000083e00000, end 0000000083e0f5cf

fixup: pfe0 set to 00:01:be:be:ef:11

fixup: pfe1 set to 00:01:be:be:ef:22

fixup: pfe1: update phy addr to 0x8

fixup: pfe2 set to 00:01:be:be:ef:33

Starting kernel ...

Reserving RAM region for PFE driver on EVB/RDB

Done.

ClockCycles samples:

0 43600679

1 43600679

2 43600678

3 43600679

4 43600678

5 43600678

6 43600678

7 43600679

All ClockCycles offsets within tolerance

Welcome to QNX Neutrino 7.1.0 on the NXP S32G399A RDB Board!!

Starting watchdog...

Starting serial driver ...

Starting Networking driver (/dev/socket)...

Process 4107 (ifconfig) exited status=0.

Process 10 (sh) exited status=0.

Process 9 (dhclient) exited status=0.

cp: Can't open source file. (/proc/boot/libfci_cli)

Process 20489 (cp) exited status=1.

Starting SPI driver (/dev/spi0,1,2,3,4,5)...

Starting I2C 0/1/2/3/4 driver (/dev/i2c0,1,2,3,4)...

Starting USDHC0 memory card driver...

[00] SIM="SDMMC" HBA="imx"

[00,0,0] type=00 ver=05 resp=00 SDMMC:

Process 24596 (chkqnx6fs) exited status=0.

Process 28692 (mount) exited status=0.

Starting QSPI Flash driver...

Starting USB host driver (/dev/usb/*)

Detected QSPI Flash: Macronix MX25UW512, JEDEC 0xC2 - 0x813A, Size: 0x4000000

Launching devb-umass for /dev/usb/* ...

#

Process 36891 (sleep) exited status=0.

sh: /var/cetitec2/startup.sh: No such file or directory

Process 45081 (sh) terminated signo=0 code=0 by process 0 value=0.

slog2info

Jan 01 00:00:00.023 random.4 low* 0 qcrypto: loading configuration file '/etc/qcrypto.conf' [qcrypto_common.c(190)]

Jan 01 00:00:00.024 random.4..0 slog* 700 Random is using the Fortuna PRNG

Jan 01 00:00:00.031 random.4 low 0 qcrypto: 'openssl' plugin loaded [qcrypto_plugins.c(354)]

Jan 01 00:00:00.031 random.4..0 slog 700 Selecting timer as an entropy source

Jan 01 00:00:00.032 random.4..0 slog 700 Registered path names

Jan 01 00:00:00.032 random.4..0 slog 700 random: starting resmgr

Jan 01 00:00:00.032 random.4..0 slog 700 random: Daemonizing the process

Jan 01 00:00:00.042 devc_serlinflexd.7 slog* 0 serlinflexd_interrupt_attach: Attaching to interrupt 114

Jan 01 00:00:00.047 iopkt.8 main_buffer* 0 tcpip starting

Jan 01 00:00:00.047 iopkt.8 main_buffer 0 smmu support is disabled

Jan 01 00:00:00.049 iopkt.8 main_buffer 0 initializing IPsec...

Jan 01 00:00:00.049 iopkt.8 main_buffer 0 done

Jan 01 00:00:00.049 iopkt.8 main_buffer 0 IPsec: Initialized Security Association Processing.

Jan 01 00:00:00.051 iopkt.8 main_buffer 0 devnp-pfe-2.so pfe0_mac=000a0b0c0d66,pfe1_mac=001a1b1c1d66,pfe2_mac=002a2b2c2d66,class_fw=/proc/boot/s32g_pfe_class.fw,pfe0_mode=sgmii,pfe0_phy=0,pfe1_mode=sgmii,pfe1_phy=1

Jan 01 00:00:00.052 io_pkt_v6_hc.8 slog* 0 INF[src/pfe_drv.c:1377]: VERSION INFO

Driver version: 1.4.0

Driver commit hash: 2f3265a49ac18f94ba5e48254c8f870fe7bfc511

PFE_CFG_MULTI_INSTANCE_SUPPORT: 0

PFE_CFG_LOCAL_IF: 6

PFE_CFG_MASTER_IF: 6

PFE_CFG_SC_HIF: 1

PFE_CFG_HIF_RING_LENGTH: 256

PFE_CFG_PFE0_PROMISC: 1

PFE_CFG_PFE1_PROMISC: 1

PFE_CFG_PFE2_PROMISC: 1

Jan 01 00:00:00.052 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1384]: --- Safe IRQ enabled. No InterrupAttach() or InterruptAttach_r() allowed.

Jan 01 00:00:00.052 io_pkt_v6_hc.8 slog 0 INF[src/pfe_fw.c:83]: 42792 bytes read

Jan 01 00:00:00.053 io_pkt_v6_hc.8 slog 0 INF[src/pfe_fw.c:89]: Loaded firmware file: /proc/boot/s32g_pfe_class.fw

Jan 01 00:00:00.053 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1477]: MII mode configuration for pfe0/EMAC0 not found. Using SGMII.

Jan 01 00:00:00.053 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1477]: MII mode configuration for pfe1/EMAC1 not found. Using SGMII.

Jan 01 00:00:00.053 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1477]: MII mode configuration for pfe2/EMAC2 not found. Using RGMII.

Jan 01 00:00:00.053 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1495]: Issuing PFE peripheral reset...

Jan 01 00:00:00.274 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1496]: PFE reset OK.

Jan 01 00:00:00.274 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:3519]: PFE CBUS p0x46000000 mapped @ v0x38f2e23000

Jan 01 00:00:00.274 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:3524]: HW version 0x101

Jan 01 00:00:00.274 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hw_feature.c:95]: Silicon S32G3

Jan 01 00:00:00.274 io_pkt_v6_hc.8 slog 0 WRN[hw/s32g/pfe_platform_master.c:3536]: Fail-Stop mode disabled

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2687]: PFE_ERRORS:Parity instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2702]: PFE_ERRORS:Watchdog instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2718]: PFE_ERRORS:Bus Error instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2731]: PFE_ERRORS:FW Fail Stop instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2744]: PFE_ERRORS:Host Fail Stop instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2757]: PFE_ERRORS:Fail Stop instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2770]: PFE_ERRORS:ECC Err instance created

Jan 01 00:00:00.275 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:1766]: BMU1 buffer base: p0xc0000000

Jan 01 00:00:00.277 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:1810]: BMU2 buffer base: p0x83000000 (0x200000 bytes)

Jan 01 00:00:00.279 io_pkt_v6_hc.8 slog 0 INF[src/oal_irq_qnx.c:117]: PFE BMU IRQ Worker started (IRQ ID: 226)

Jan 01 00:00:00.279 io_pkt_v6_hc.8 slog 0 WRN[hw/s32g/pfe_platform_master.c:2194]: The option 'g2_ordered_class_writes' is disabled.

Jan 01 00:00:00.279 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_bmu_csr.c:96]: BMU_EMPTY_INT (BMU @ p0x88000). Pool ready.

Jan 01 00:00:00.279 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_bmu_csr.c:96]: BMU_EMPTY_INT (BMU @ p0x8c000). Pool ready.

Jan 01 00:00:00.281 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2239]: Firmware .elf detected

Jan 01 00:00:00.281 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2248]: Uploading CLASS firmware

Jan 01 00:00:00.281 io_pkt_v6_hc.8 slog 0 INF[src/pfe_pe.c:609]: Selected FW loading OPs to load 8 PEs in parallel

Jan 01 00:00:00.285 io_pkt_v6_hc.8 slog 0 INF[src/pfe_pe.c:1945]: pfe_ct.h file version"92367c0e25f21f49217a9b08168ad2c8"

Jan 01 00:00:00.288 io_pkt_v6_hc.8 slog 0 INF[src/pfe_pe.c:2422]: [FW VERSION] 1.7.0, Build: Jun 2 2023, 13:48:57 (nogitaaa), ID: 0x31454650

Jan 01 00:00:00.406 io_pkt_v6_hc.8 slog 0 WRN[hw/s32g/pfe_platform_master.c:2312]: VLAN ID incorrect or not set. Using default VLAN ID = 0x01.

Jan 01 00:00:00.406 io_pkt_v6_hc.8 slog 0 WRN[hw/s32g/pfe_platform_master.c:2318]: VLAN stats size incorrect or not set. Using default VLAN stats size = 20.

Jan 01 00:00:00.406 io_pkt_v6_hc.8 slog 0 INF[src/pfe_l2br.c:1181]: Software vlan hash table @ p0x20001228

Jan 01 00:00:00.406 io_pkt_v6_hc.8 slog 0 INF[src/pfe_l2br.c:1286]: Fall-back bridge domain @ 0x20000a7c (class)

Jan 01 00:00:00.406 io_pkt_v6_hc.8 slog 0 INF[src/pfe_l2br.c:1287]: Default bridge domain @ 0x20000a74 (class)

Jan 01 00:00:00.406 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:2412]: Routing table created, Hash Table @ p0x80014000, Pool @ p0x8001c000 (65536 bytes)

Jan 01 00:00:00.407 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_chnl.c:1997]: Initializing RX buffer pool. Depth: 256; Buffer Size: 2048; Cache Line Size: 64

Jan 01 00:00:00.408 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_chnl.c:1997]: Initializing RX buffer pool. Depth: 256; Buffer Size: 2048; Cache Line Size: 64

Jan 01 00:00:00.409 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_chnl.c:1997]: Initializing RX buffer pool. Depth: 256; Buffer Size: 2048; Cache Line Size: 64

Jan 01 00:00:00.508 io_pkt_v6_hc.8 slog 0 INF[hw/s32g/pfe_platform_master.c:3705]: Feature err051211_workaround: DISABLED

Jan 01 00:00:00.509 iopkt.8 main_buffer 0 pfe0

Jan 01 00:00:00.509 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2152]: pfe0: Using PHY mode: MDIO=0, ADDR=0, CLAUSE=0, RESET=0

Jan 01 00:00:00.509 io_pkt_v6_hc.8 slog 0 INF[src/oal_irq_qnx.c:117]: PFE HIF0 IRQ Worker started (IRQ ID: 222)

Jan 01 00:00:00.509 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1795]: Adding 00:0a:0b:0c:0d:66 to pfe0

Jan 01 00:00:00.511 iopkt.8 main_buffer 0 pfe1

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2298]: Speed/duplex configuration for pfe0 not found. Using 1 Gbps/full-duplex.

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_drv_sc.c:336]: Attempt to register HIF client: 0

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_drv_sc.c:1189]: HIF driver started

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2363]: New PFE device: 0, ID: 0

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2152]: pfe1: Using PHY mode: MDIO=1, ADDR=0, CLAUSE=0, RESET=0

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/oal_irq_qnx.c:117]: PFE HIF1 IRQ Worker started (IRQ ID: 223)

Jan 01 00:00:00.511 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1795]: Adding 00:1a:1b:1c:1d:66 to pfe1

Jan 01 00:00:00.513 iopkt.8 main_buffer 0 pfe2

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2298]: Speed/duplex configuration for pfe1 not found. Using 1 Gbps/full-duplex.

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_drv_sc.c:336]: Attempt to register HIF client: 1

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_drv_sc.c:1189]: HIF driver started

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2363]: New PFE device: 1, ID: 2

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2145]: pfe2: Using static PHY mode, RESET=0

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/oal_irq_qnx.c:117]: PFE HIF2 IRQ Worker started (IRQ ID: 224)

Jan 01 00:00:00.513 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:1795]: Adding 00:2a:2b:2c:2d:66 to pfe2

Jan 01 00:00:00.515 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2298]: Speed/duplex configuration for pfe2 not found. Using 1 Gbps/full-duplex.

Jan 01 00:00:00.515 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_drv_sc.c:336]: Attempt to register HIF client: 2

Jan 01 00:00:00.515 io_pkt_v6_hc.8 slog 0 INF[src/pfe_hif_drv_sc.c:1189]: HIF driver started

Jan 01 00:00:00.515 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2363]: New PFE device: 2, ID: 4

Jan 01 00:00:00.530 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2702]: Adding 00:0a:0b:0c:0d:66 to pfe0

Jan 01 00:00:00.530 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2707]: Unable to assign MAC address 00:0a:0b:0c:0d:66 to the pfe0

Jan 01 00:00:00.530 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2663]: pfe0: Disabling promiscuous mode

Jan 01 00:00:00.538 io_pkt_v6_hc.8 slog 0 INF[src/pfe_mdio.c:427]: pfe0: PHY @ bus 0 addr 0 not found. Switching to static mode.

Jan 01 00:00:00.538 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2829]: EMAC speed change for SGMII is currently not supported.

Jan 01 00:00:00.538 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:ff:0c:0d:66 to emac0

Jan 01 00:00:00.540 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2663]: pfe0: Disabling promiscuous mode

Jan 01 00:00:00.540 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:00:00:00:01 to emac0

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:ff:0c:0d:66 to emac0

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2450]: unable to add 33:33:ff:0c:0d:66 into emac0: 17

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2663]: pfe0: Disabling promiscuous mode

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:00:00:00:01 to emac0

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2450]: unable to add 33:33:00:00:00:01 into emac0: 17

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:ff:0c:0d:66 to emac0

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2450]: unable to add 33:33:ff:0c:0d:66 into emac0: 17

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2663]: pfe0: Disabling promiscuous mode

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2829]: EMAC speed change for SGMII is currently not supported.

Jan 01 00:00:00.542 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 01:00:5e:00:00:01 to emac0

Jan 01 00:00:00.544 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:00:00:00:01 to emac0

Jan 01 00:00:00.544 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2450]: unable to add 33:33:00:00:00:01 into emac0: 17

Jan 01 00:00:00.544 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2443]: Adding 33:33:ff:0c:0d:66 to emac0

Jan 01 00:00:00.544 io_pkt_v6_hc.8 slog 0 WRN[src/pfe_drv.c:2450]: unable to add 33:33:ff:0c:0d:66 into emac0: 17

Jan 01 00:00:00.544 io_pkt_v6_hc.8 slog 0 INF[src/pfe_drv.c:2663]: pfe0: Disabling promiscuous mode

Jan 01 00:00:00.554 spi_master.24585 normal* 0 Starting spi-master resource manager

Jan 01 00:00:00.558 spi_master.24587 normal* 0 Starting spi-master resource manager

Jan 01 00:00:00.561 spi_master.24588 normal* 0 Starting spi-master resource manager

Jan 01 00:00:00.565 spi_master.24589 normal* 0 Starting spi-master resource manager

Jan 01 00:00:00.582 devb_sdmmc_mx8x.24595 slog* 1800 devb-sdmmc-mx8x 1.00A (Jun 23 2026 09:45:48)

Jan 01 00:00:00.583 devb_sdmmc_mx8x.24595 slog 0 libcam.so (Jun 22 2020 21:33:15) bver 7010003

Jan 01 00:00:00.594 devb_sdmmc_mx8x.24595 slog 1800 sdio_cd: insertion path 0, cd state 0x1

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 SD CID:

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 MID 0x27, OID 0x5048, PNM SD32G

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 PRV 0x62, PSN 0x6c62d132, MDT 4-2023

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 SD CSD:

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 CSD_STRUCTURE 1, SPEC_VERS 0, CCC 0x5b5

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 TAAC 14, NSAC 0, TRAN_SPEED 50

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 C_SIZE 59023, C_SIZE_MULT 0

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 READ_BL_LEN 9, WRITE_BL_LEN 9

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 ERASE GRP_SIZE 0, GRP_MULT 0, SIZE 127

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 blksz 512, sectors 60440576, dtr 25000000

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 SD SW CAPS:

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 bus mode 0x3, cmd sys 0x1

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 drv type 0x1, curr limit 0x1

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 dtr 50000000

Jan 01 00:00:00.644 devb_sdmmc_mx8x.24595 slog 1800 CFG: Timing HS, DTR 50000000, Bus Width 4 bit

Jan 01 00:00:00.645 devb_sdmmc_mx8x.24595 slog 100 cam-disk.so (Jun 22 2020 21:33:17)

Jan 01 00:00:00.647 devb_sdmmc_mx8x.24595 slog 0 scsi_interpret_sense (sdmmc ptl-0:0:0): cam_status=c4, scsi_status=2, flag=00000040, vuflag=0008, cmd=1a, error=70, sense=5, asc=24, ascq=0

Jan 01 00:00:00.647 devb_sdmmc_mx8x.24595 slog 0 scsi_interpret_sense (sdmmc ptl-0:0:0): cam_status=c4, scsi_status=2, flag=00000040, vuflag=0008, cmd=5a, error=70, sense=5, asc=24, ascq=0

Jan 01 00:00:01.827 devb_sdmmc_mx8x.24595 slog 1000 fs-qnx6: Allocation strategy 0

Jan 01 00:00:01.827 devb_sdmmc_mx8x.24595 slog 1000 fs-qnx6: Use btree directory 0

Jan 01 00:00:01.828 devb_sdmmc_mx8x.24595 slog 1000 fs-qnx6: fs-qnx6: trim (0,1048576,2) was not requested, and is NOT supported

Jan 01 00:00:01.833 io_usb_otg.36885 slog* 0 main(453)[tid:1]: io-usb-otg (Jun 13 2020 20:10:17) args: -d hcd-ehci-mx28 ioport=0x44064100,irq=243,ulpi,no_stream,verbose=5

Jan 01 00:00:01.835 devf_qspi_s32g.36884 slog* 0 (devf t1::f3s_qspi_ident:73) Page size: 256

Jan 01 00:00:01.835 devf_qspi_s32g.36884 slog 0 (devf t1::f3s_qspi_ident:74) Total chip size: 0x4000000, Unit size: 0x10000

Jan 01 00:00:01.839 io_usb_otg.36885 slog 0 ehci_init: Initialiaing with sever version: 2

Jan 01 00:00:01.839 io_usb_otg.36885 slog 0 ehci_controller_init(4303): devu-hcd-ehci-mx28.so (Apr 19 2024 13:44:54): args ulpi,no_stream,verbose=5

Jan 01 00:00:01.840 io_usb_otg.36885 slog 8 usb_enum_port(94)[tid:1]: busno 0, parent -1, port 0, High speed

Jan 01 00:00:01.840 io_usb_otg.36885 slog 11 usb_client_descriptor_get(198)[tid:1]: (type 1, index 0, length

Jan 01 00:00:01.840 io_usb_otg.36885 slog 12 usb_device_set_address(245)[tid:1]: b:0 devno 0

Jan 01 00:00:01.840 io_usb_otg.36885 slog 11 usb_client_descriptor_get(198)[tid:1]: (type 1, index 0, length 18)

Jan 01 00:00:01.841 io_usb_otg.36885 slog 11 usb_client_descriptor_get(198)[tid:1]: (type 2, index 0, length 9)

Jan 01 00:00:01.841 io_usb_otg.36885 slog 11 usb_client_descriptor_get(198)[tid:1]: (type 2, index 0, length 25)

Jan 01 00:00:01.841 io_usb_otg.36885 slog 8 usb_enum_port(141)[tid:1]: vid 0x0000, did 0x0000 enumerated(busno 0, devno 0:0)

Jan 01 00:00:01.841 io_usb_otg.36885 slog 11 hub_state_inserted(569)[tid:1]: bdentry 0, dentry 0 0

Jan 01 00:00:01.841 io_usb_otg.36885 slog 13 hub_configuration_enable(263)[tid:1]: 1

Jan 01 00:00:01.943 io_usb_otg.36885 slog 0 usbh_timeout_init(203)[tid:1]: Complete

Jan 01 00:00:01.954 io_usb_otg.36885 slog 0 read_vid_pid: ULPI VID 0x0424 PID 0x0009

Jan 01 00:00:01.954 io_usb_otg.36885 slog 0 s32g_phy_set_vbus: set_vbus off

Jan 01 00:00:01.968 io_usb_otg.36885 slog 0 s32g_phy_set_vbus: set_vbus on

Jan 01 00:00:01.979 io_usb_otg.36885 slog 0 ehci_get_port_status(3568 0x44064100): port=0, tpstatus 10100 e_pstatus 8c001000

Jan 01 00:00:01.979 io_usb_otg.36885 slog 8 usb_enum_port_extract(172)[tid:7]: (busno 0, pdevno 0, portno 1)

Jan 01 00:00:01.979 io_usb_otg.36885 slog 8 usb_enum_port_extract(192)[tid:7]: status (2)

Jan 01 00:00:01.983 devb_umass.36886 slog* 900 devb-umass 1.00A (Jun 22 2020 21:33:41)

Jan 01 00:00:01.984 devb_umass.36886 slog 0 libcam.so (Jun 22 2020 21:33:15) bver 7010003

Jan 01 00:00:01.985 io_usb_otg.36885 slog 0 usbdi_client_connect(58)[tid:5]: pid 36886 proc=proc/boot/devb-umass usbdi_client 32eebb9a80

Jan 01 00:00:01.986 io_usb_otg.36885 slog 0 usbdi_resmgr_connect(310)[tid:5]: usbdi_resmgr_connect: pid 36886 usbdi_client 32eebb9a80

Jan 01 00:00:01.986 devb_umass.36886 slog 0 usbdi debug path /pps/usb/debug/ doesn't exist

Process 49177 (slog2info) exited status=0.

# ifconfig

lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33136

inet 127.0.0.1 netmask 0xff000000

inet6 ::1 prefixlen 128

inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1

pfe0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500

capabilities=1f<IP4CSUM,TCP4CSUM,UDP4CSUM,TCP6CSUM,UDP6CSUM>

enabled=0

address: 00:0a:0b:0c:0d:66

media: Ethernet none (1000baseT full-duplex)

status: active

inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255

inet6 fe80::20a:bff:fe0c:d66%pfe0 prefixlen 64 scopeid 0x11

pfe1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500

capabilities=1f<IP4CSUM,TCP4CSUM,UDP4CSUM,TCP6CSUM,UDP6CSUM>

enabled=0

address: 00:1a:1b:1c:1d:66

media: Ethernet none (1000baseT full-duplex)

status: no carrier

pfe2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500

capabilities=1f<IP4CSUM,TCP4CSUM,UDP4CSUM,TCP6CSUM,UDP6CSUM>

enabled=0

address: 00:2a:2b:2c:2d:66

media: Ethernet none (1000baseT full-duplex)

status: no carrier

Process 57369 (ifconfig) exited status=0.

#