IMX8MPLUS SENSOR CALIBRATION FILES

[venom]

Hi,
Currently i am working on imx415 camera sensor porting on imx8mplus ,i have customized my imx415 driver according to camera sensor porting guide.
What i don't have are the sensor calibration files. Now, even if i don't have calibration file is will my camera work and send data to ISP?? 
Is it really important that i have sensor calibration files??Can i skip that part or not??
For now, without any calbration files i cannot stream.I can see that it actually triggers a ioctl call "VIDIOC_QUERYCAP" in my sensor driver but after that i can see a isp driver log that enables streams and immediately disabling.  What might be the reason for this??.

LOG:

[ 194.089080] imx415 1-001a: Inside VIDIOC_QUERYCAP
[ 194.118862] enter isp_mi_stop
[ 195.511209] enter isp_set_stream 1
[ 212.626549] enter isp_set_stream 0

Thank you,
Regards Harsha.

[Oswalag]

Hello,

the answer is yes, you need the calibration files as explained in the ISP New Camera Sensor Porting and Integration Guide for i.MX 8M Plus EVK.

[venom]

Hi,

While streaming, I can observe the following logs. Could you help me understand what the possible reasons for this behavior might be?

I am not receiving frame end at all.

[Oswalag]

Please modify the DTS node as:

Configure 266MHz clock on the second MIPI-CSI2 port:

+&mipi_csi_1 {

+      #address-cells = <1>;

+      #size-cells = <0>;

+

+      clock-frequency = <266000000>;

+      assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>;

+      assigned-clock-rates = <266000000>;

+

+      status = "okay";

+

+      port@1 {

+              reg = <1>;

+              mipi_csi1_ep: endpoint {

+                      remote-endpoint = <&jxf355_mipi_1_ep>;

+                      data-lanes = <2>;

+

+                      csis-hs-settle = <5>;

+                      csis-clk-settle = <0>;

+                      csis-wclk;

+              };

+      };

+};

[venom]

Hi,
I am using only one csi port & my device tree configuration is as follows:

imx415_0: imx415_mipi@1a {
     compatible = "sony,imx415";
     reg = <0x1a>;
     clocks = <0x1a>;
     assigned-clocks = <0x1a>;
     assigned-clock-rates = <0x16E3600>;
     clock-names = "csi_mclk";
     status = "okay";
     csi_id = <0x00>;

port {
      imx415_0_ep: endpoint {
                   remote-endpoint = <&csi0_ep>;
                   clock-lanes = <0x00>;
                   link-frequencies = /bits/ 64 <360000000>;
                   max-pixel-frequency = <0x00 0x1dcd6500>;
                  data-lanes = <0x01 0x02 0x03 0x04>;
                  };
       };
};

csi@32e40000 {
       compatible = "fsl,imx8mp-mipi-csi\0fsl,imx8mn-mipi-csi";
       reg = <0x32e40000 0x10000>;
       interrupts = <0x00 0x11 0x04>;
       clock-frequency = <0x1dcd6500>;
       clocks = <0x02 0x10f 0x02 0x61 0x02 0x10d>;
       clock-names = "mipi_clk\0disp_axi\0disp_apb";
       assigned-clocks = <0x02 0xaa>;
       assigned-clock-parents = <0x02 0x41>;
       assigned-clock-rates = <0x1dcd6500>;
       bus-width = <0x04>;
       csi-gpr = <0x74>;
       gpr = <0x5b>;
       power-domains = <0x5b 0x01>;
       status = "okay";
       phandle = <0x10e>;

port {
          csi0_ep: endpoint {
                     remote-endpoint = <&imx415_0_ep>;
                     data-lanes = <4>;
                     csis-hs-settle = <0x0F>;
                     csis-clk-settle = <0x10>;
                   };
         };

};

If my sensor is in continuous mode does it work??