Enable XRDC in S32G

[Atkinson]

Hi,
How can i enable the XRDC ?
Whether should i need to Bring some peripheral component of XRDC if yes, can you share me the peripheral component to download and bring it into the SDK ?
I have referred the "AN13024 S32G Extended Resource Domain Controller (XRDC)"
can you be more specific how to configure and differentiate the process of handling 

Regards
Atkinson

[Joey_z]

hi，Atkinson

You can refer to the AN13024 of chapter about how to initial XRDC, it is a demo flow as the following picture.

Also, typical use case would have the M7_0 core (acting as the safety core) configure the XRDC at device boot before bringing other cores out of reset.

Hope this can help you.

BR

Joey

[Atkinson]

Hi @Joey_z 

I went to the Documentation it was complete sort of theory where this theory completely depicts the flow of XRDC but, 
I would like to get the Configuration 
where to start the configuration? which are the files need to be changed with the assignment? 
Where to change the memory assignment ? 
can you give the complete brief about the note how i can move forward with the configuration
The documentation gives the theory perspective there is no example configuration 
so i would like to get the example configuration ?

Regards
Atkinson

[Joey_z]

hi,Atkinson

Thank you for your reply.

You can refer to the Goldvip content and RTD demo to know about the XRDC using. It is as the following picture.

Hope this can help you.

BR

Joey

[Atkinson]

Hi @Joey_z 

I do able to access the document.
1.)Where can i download the "Bootloader_platform>_ASR_4.4_M7" workspace whether this will be integrated with the PDF ?
2.)This configuration setting it will be performed only via the EB tresos or it can be also performed via the S32DS SDK ?
3.)So apart from this one small doubt so in this XRDC configuration were will we be able to bring the different OS ?

Regards
Atkinson

[Joey_z]

hi,Atkinson

Thank you for your reply.

1.)Where can i download the "Bootloader_platform>_ASR_4.4_M7" workspace whether this will be integrated with the PDF ?

>>>You can download Goldvip package to refer to this link:Design : Product Download : Files

2.)This configuration setting it will be performed only via the EB tresos or it can be also performed via the S32DS SDK ?

>>> The RTD demo can be used in EB or S32DS IDE, Goldvip package only is used in EB tresos.

3.)So apart from this one small doubt so in this XRDC configuration were will we be able to bring the different OS ?

>>>You can refer to the AN13024, the following figure shows a simple example usage of S32G274A on S32G-VNP-RDB.

Hope this can help you.

BR

Joey

[Atkinson]

Hi @Joey_z 

I got the "Bootloader_platform>_ASR_4.4_M7" 
So for the EB Tresos we need to install RTD packages right so where can i find the RTD Packages for EB Tresos ? because when i opened the ECU part it showing me some errors like below

An error occurred while loading the module Mcu.
For details click on the items below.

Click "Remove Module" to remove the module configuration finally from the project and continue loading.
Click "Remove all faulty Modules" to remove all faulty module configurations finally from the project and continue loading.
Click "Cancel Load" to stop loading the project and return to the main windows.

"Plug-in with a module "Mcu_TS_T40D11M40I0R0" is not installed - cannot create module configurations for project "Bootloader_S32G2XX_ASR_4.4_M7""

can you share me the dependencies file which needed for it to overcome this issue
So can you suggest me how can i configure it complete via S32DS 

[Joey_z]

hi，Atkinson

Thank you for your reply.

The package of (Mcu_TS_T40D11M40I0R0) can be found int the RTD 4.0.0. The folder is :

C:\nxp\SW32_RTD_4.4_4.0.0\eclipse\plugins

Also, you should apply the Goldvip package in the EB Tresos.

BR

Joey

[Atkinson]

Hi @Joey_z 

I have found the package so where should i need to keep the package -->in which folder should i need to put this folder "Mcl_TS_T40D11M40I2R0"
So that the issue can be resolved
Can you be more specific

Regards
Atkinson

[Joey_z]

hi，Atkinson

Thank you for your reply.

You can try to add the package to the folder(C:\EB\tresos\plugins) of EB Tresos.

BR

Joey

[Atkinson]

Hi @Joey_z 

After including the plugins files into the respective folder still not able to see the configuration files inside the EcuC (CORTEXM, S32G2XXM7) so how to overcome that issue 

Regards
Atkinson

[Joey_z]

hi，Atkinson

Which package you can find it? Could you tell me the complete name of package?

BR

Joey

[Atkinson]

Hi @Joey_z 

I have currently copied the all files inside the EB/tresos/Plugins/

The folder contains 

Mcu_TS_T40D11M40I0R0 which you mentioned it but still not working as expected 

Regards
Atkinson

[Joey_z]

hi，Atkinson

Dose your EB Tresos has any error information? Could you share it with me? I can help you to check it.

BR

Joey

[Joey_z]

hi，Atkinson

Thank you for contacting us.

Could you share more information with us?

Are you using the S32G2 or S32G3? And do you want to use the A core or M core?

BR

Joey

[Atkinson]

Hi @Joey_z 

Thanks for the quick reply 
I am using S32G274ARDB2 Board 
I am comfortable to bring either in A - core or M7 - Core 
Currently i am trying to bring either in A-core or M7 - core 
Can you provide me perspective for both also i would like to choose depends on difficulty level