Hi Juan,
I think you have to use FB_AD[1:16] to connect with the address lines of the device, data connection should be fine, and for flexbus initialization, please kindly refer to the following sample code for details.
void TWRK60_flexbus_init(void){
/* Enable the FlexBus */
/* Configure the FlexBus Registers for 8-bit port size */
/* with separate address and data using chip select 0 */
/* These configurations are specific to communicating with */
/* the MRAM used in this example */
/* For K60 tower module - do not set byte lane shift so that data */
/* comes out on AD[31:24] */
//Set Base address
FB_CSAR0 = (uint32)&MRAM_START_ADDRESS;
FB_CSCR0 = FB_CSCR_PS(1) // 8-bit port
| FB_CSCR_AA_MASK // auto-acknowledge
| FB_CSCR_ASET(0x1) // assert chip select on second clock edge after address is asserted
| FB_CSCR_WS(0x1) // 1 wait state - may need a wait state depending on the bus speed
;
FB_CSMR0 = FB_CSMR_BAM(0x7) //Set base address mask for 512K address space
| FB_CSMR_V_MASK //Enable cs signal
;
//enable BE signals - note, not used in this example
FB_CSPMCR = 0x02200000;
//fb clock divider 3
SIM_CLKDIV1 |= SIM_CLKDIV1_OUTDIV3(0x3);
/* Configure the pins needed to FlexBus Function (Alt 5) */
/* this example uses low drive strength settings */
//address
PORTB_PCR11 = PORT_PCR_MUX(5); // fb_ad[18]
PORTB_PCR16 = PORT_PCR_MUX(5); // fb_ad[17]
PORTB_PCR17 = PORT_PCR_MUX(5); // fb_ad[16]
PORTB_PCR18 = PORT_PCR_MUX(5); // fb_ad[15]
PORTC_PCR0 = PORT_PCR_MUX(5); // fb_ad[14]
PORTC_PCR1 = PORT_PCR_MUX(5); // fb_ad[13]
PORTC_PCR2 = PORT_PCR_MUX(5); // fb_ad[12]
PORTC_PCR4 = PORT_PCR_MUX(5); // fb_ad[11]
PORTC_PCR5 = PORT_PCR_MUX(5); // fb_ad[10]
PORTC_PCR6 = PORT_PCR_MUX(5); // fb_ad[9]
PORTC_PCR7 = PORT_PCR_MUX(5); // fb_ad[8]
PORTC_PCR8 = PORT_PCR_MUX(5); // fb_ad[7]
PORTC_PCR9 = PORT_PCR_MUX(5); // fb_ad[6]
PORTC_PCR10 = PORT_PCR_MUX(5); // fb_ad[5]
PORTD_PCR2 = PORT_PCR_MUX(5); // fb_ad[4]
PORTD_PCR3 = PORT_PCR_MUX(5); // fb_ad[3]
PORTD_PCR4 = PORT_PCR_MUX(5); // fb_ad[2]
PORTD_PCR5 = PORT_PCR_MUX(5); // fb_ad[1]
PORTD_PCR6 = PORT_PCR_MUX(5); // fb_ad[0]
//data
PORTB_PCR20 = PORT_PCR_MUX(5); // fb_ad[31] used as d[7]
PORTB_PCR21 = PORT_PCR_MUX(5); // fb_ad[30] used as d[6]
PORTB_PCR22 = PORT_PCR_MUX(5); // fb_ad[29] used as d[5]
PORTB_PCR23 = PORT_PCR_MUX(5); // fb_ad[28] used as d[4]
PORTC_PCR12 = PORT_PCR_MUX(5); // fb_ad[27] used as d[3]
PORTC_PCR13 = PORT_PCR_MUX(5); // fb_ad[26] used as d[2]
PORTC_PCR14 = PORT_PCR_MUX(5); // fb_ad[25] used as d[1]
PORTC_PCR15 = PORT_PCR_MUX(5); // fb_ad[24] used as d[0]
//control signals
PORTB_PCR19 = PORT_PCR_MUX(5); // fb_oe_b
PORTC_PCR11 = PORT_PCR_MUX(5); // fb_rw_b
PORTD_PCR1 = PORT_PCR_MUX(5); // fb_cs0_b
PORTD_PCR0 = PORT_PCR_MUX(5); // fb_ale
}
Hope that helps,
Have a great day,
Kan
-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------
