Hi Zhijun wu,
1. Please check the default board configuration.
You can refer to TWR-KV58F220MUG.pdf in the TWR-KV58F220M-QSP
But take care, the TWR-KV58F220MUG have a error about J29 and J28, J29 should be open, J28 should connect 1-2.
Please make sure your board's configuration is in default.
Then try again.
2. If item 1 still not OK, please try to use JLINK firmware, which you can find int TWR-KV58F220M-QSP, the folder is:TWR-KV58F220M-QSP\TWR-KV58F220M_Quick Start Package\OpenSDA Application\Segger OpenSDA\JLink_OpenSDA_V2_1_2015-10-13.bin
1) install JLINK driver
SEGGER - The Embedded Experts - Downloads - J-Link / J-Trace
2) unplug your board, then press RESET button and hold on it, at the same time, plug board to your PC, you will find your board is a device named as"BOOTLOADER"
3) Send "JLink_OpenSDA_V2_1_2015-10-13.bin" to "BOOTLOADER"
4) unplug your board and plug it again.
You will find your board is a device named as "JLINK"
5) Use JLINK command to check ,whether you can find Cortex-M7?
If the core is found, then you can download your code again with JLINK debugger.
Please use the SDK_2.0_TWR-KV58F220M sample code to test it.
You can find KSDK2.0 from this link:
Welcome to Kinetis Expert | Kinetis Expert
Click build an SDK, and generate the SDK_2.0_TWR-KV58F220M package.
Wish it helps you!
Have a great day,
Kerry
-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------
Hi Zhijun wu,
1. Please check the default board configuration.
You can refer to TWR-KV58F220MUG.pdf in the TWR-KV58F220M-QSP
But take care, the TWR-KV58F220MUG have a error about J29 and J28, J29 should be open, J28 should connect 1-2.
Please make sure your board's configuration is in default.
Then try again.
2. If item 1 still not OK, please try to use JLINK firmware, which you can find int TWR-KV58F220M-QSP, the folder is:TWR-KV58F220M-QSP\TWR-KV58F220M_Quick Start Package\OpenSDA Application\Segger OpenSDA\JLink_OpenSDA_V2_1_2015-10-13.bin
1) install JLINK driver
SEGGER - The Embedded Experts - Downloads - J-Link / J-Trace
2) unplug your board, then press RESET button and hold on it, at the same time, plug board to your PC, you will find your board is a device named as"BOOTLOADER"
3) Send "JLink_OpenSDA_V2_1_2015-10-13.bin" to "BOOTLOADER"
4) unplug your board and plug it again.
You will find your board is a device named as "JLINK"
5) Use JLINK command to check ,whether you can find Cortex-M7?
If the core is found, then you can download your code again with JLINK debugger.
Please use the SDK_2.0_TWR-KV58F220M sample code to test it.
You can find KSDK2.0 from this link:
Welcome to Kinetis Expert | Kinetis Expert
Click build an SDK, and generate the SDK_2.0_TWR-KV58F220M package.
Wish it helps you!
Have a great day,
Kerry
-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------
Hi Kerry Zhou,
Thank you for your great answer!
item 1 isn't the solution,maybe I have been reset the CPU before.
But item 2 is ok, I follow your item 2 steps,and finally,CPU is identified.
the following is my result:
now , can I just use J-Link to download my program? can't use openSDA miniUSB CMSIS-DAP anymore?
hello Kerry,
I reuse CMSIS-DAP fireware to download promgram ,but "reading CPU status failed " problem is also exist.
I following the default jumper setting :
in the file "TWR-KV58F220M Quick Start Guide":
in the file "TWR-KV58F220M Tower Module User's Guide":
and change the J29 to off(open) (you said "the TWR-KV58F220MUG have a error about J29 and J28, J29 should be open, J28 should connect 1-2.")。
following picture is the real jumper setting in my twr-kv58f220:
is this problem a other hardware or software error?
Hi zhijun,
The workaround for IAR with cmsis dap debugger problem is :
Please chose software, then build and download again, the problem will be dissappeared
Wish it helps you!
Have a great day,
Kerry
-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------
Hi Zhijun,
Your hardware configuration is correct, I also the same with you.
When you use the CMSIS DAP, and click the download, do you meet this problem?
I have reproduced your problem with the OSP CMSIS firmware, I will report it to our according department.
Now, please use the JLINK firmware to download the code, this firmware have no problem.
Wish it helps you!
Have a great day,
Kerry
-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------
