imx8mp uuu download failed (No udc Available!)

[dskim2]

Hello

I tried to download yocto image with uuu tool but failed

How can I fix it.

below is uuu and device log

[uuu log]

uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.4.139-0-g1a8f760

Build in config:
Pctl Chip Vid Pid BcdVersion
==================================================
SDPS: MX8QXP 0x1fc9 0x012f [0x0002..0xffff]
SDPS: MX8QM 0x1fc9 0x0129 [0x0002..0xffff]
SDPS: MX8DXL 0x1fc9 0x0147
SDPS: MX28 0x15a2 0x004f
SDPS: MX815 0x1fc9 0x013e
SDPS: MX865 0x1fc9 0x0146
SDPS: MX8ULP 0x1fc9 0x014a
SDPS: MX8ULP 0x1fc9 0x014b
SDP: MX7D 0x15a2 0x0076
SDP: MX6Q 0x15a2 0x0054
SDP: MX6D 0x15a2 0x0061
SDP: MX6SL 0x15a2 0x0063
SDP: MX6SX 0x15a2 0x0071
SDP: MX6UL 0x15a2 0x007d
SDP: MX6ULL 0x15a2 0x0080
SDP: MX6SLL 0x1fc9 0x0128
SDP: MX7ULP 0x1fc9 0x0126
SDP: MXRT106X 0x1fc9 0x0135
SDP: MX8MM 0x1fc9 0x0134
SDP: MX8MQ 0x1fc9 0x012b
SDPU: SPL 0x0525 0xb4a4 [0x0000..0x04ff]
SDPV: SPL1 0x0525 0xb4a4 [0x0500..0x9998]
SDPU: SPL 0x0525 0xb4a4 [0x9999..0x9999]
SDPU: SPL 0x3016 0x1001 [0x0000..0x04ff]
SDPV: SPL1 0x3016 0x1001 [0x0500..0x9998]
FBK: 0x066f 0x9afe
FBK: 0x066f 0x9bff
FB: 0x0525 0xa4a5
FB: 0x18d1 0x0d02
FB: 0x3016 0x0001
Wait for Known USB Device Appear...
New USB Device Attached at 2:141
2:141>Start Cmd:SDPS: boot -f imx8mp_flash_2G_4000.bin
100%2:141>Okay (1.894s)
New USB Device Attached at 2:141
2:141>Start Cmd:FB: ucmd setenv fastboot_dev mmc
2:141>Okay (0.022s)
2:141>Start Cmd:FB: ucmd setenv mmcdev ${emmc_dev}
2:141>Okay (0.313s)
2:141>Start Cmd:FB: flash bootloader imx8mp_flash_2G_4000.bin
0x400000002:141>Okay (0.432s)
2:141>Start Cmd:FB: ucmd if env exists emmc_ack; then ; else setenv emmc_ack 0; fi;
2:141>Okay (0.011s)
2:141>Start Cmd:FB: ucmd setenv emmc_cmd mmc partconf ${emmc_dev} ${emmc_ack} 1 0
2:141>Okay (0.013s)
2:141>Start Cmd:FB: ucmd if test "${emmc_skip_fb}" != "yes"; then run emmc_cmd; fi
2:141>Okay (0.014s)
2:141>Start Cmd:FB: ucmd setenv emmc_cmd mmc bootbus ${emmc_dev} 2 2 1;
2:141>Okay (0.013s)
2:141>Start Cmd:FB: ucmd if test "${emmc_skip_fb}" != "yes"; then run emmc_cmd; fi
2:141>Okay (0.013s)
2:141>Start Cmd:FB: ucmd setenv fastboot_buffer ${loadaddr}
2:141>Okay (0.012s)
2:141>Start Cmd:FB: download -f Image
2:141>Okay (1.554s)
2:141>Start Cmd:FB: ucmd setenv fastboot_buffer ${fdt_addr}
2:141>Okay (0.012s)
2:141>Start Cmd:FB: download -f imx8mp-evk.dtb
2:141>Okay (0.025s)
2:141>Start Cmd:FB: ucmd setenv fastboot_buffer ${initrd_addr}
2:141>Okay (0.03s)
2:141>Start Cmd:FB: download -f fsl-image-mfgtool-initramfs-imx_mfgtools.cpio.zst.u-boot
2:141>Okay (0.624s)
2:141>Start Cmd:FB: acmd ${kboot} ${loadaddr} ${initrd_addr} ${fdt_addr}
2:141>Okay (0.009s)
New USB Device Attached at 2:141
2:141>Start Cmd:SDPS: boot -f imx8mp_flash_2G_4000.bin
100%2:141>Okay (1.91s)
New USB Device Attached at 2:141
2:141>Start Cmd:FB: ucmd setenv fastboot_dev mmc
2:141>Okay (0.023s)
2:141>Start Cmd:FB: ucmd setenv mmcdev ${emmc_dev}
2:141>Okay (0.297s)
2:141>Start Cmd:FB: flash bootloader imx8mp_flash_2G_4000.bin
0x400000002:141>Okay (0.451s)
2:141>Start Cmd:FB: ucmd if env exists emmc_ack; then ; else setenv emmc_ack 0; fi;
2:141>Okay (0.013s)
2:141>Start Cmd:FB: ucmd setenv emmc_cmd mmc partconf ${emmc_dev} ${emmc_ack} 1 0
2:141>Okay (0.012s)
2:141>Start Cmd:FB: ucmd if test "${emmc_skip_fb}" != "yes"; then run emmc_cmd; fi
2:141>Okay (0.012s)
2:141>Start Cmd:FB: ucmd setenv emmc_cmd mmc bootbus ${emmc_dev} 2 2 1;
2:141>Okay (0.015s)
2:141>Start Cmd:FB: ucmd if test "${emmc_skip_fb}" != "yes"; then run emmc_cmd; fi
2:141>Okay (0.013s)
2:141>Start Cmd:FB: ucmd setenv fastboot_buffer ${loadaddr}
2:141>Okay (0.012s)
2:141>Start Cmd:FB: download -f Image
2:141>Okay (1.608s)
2:141>Start Cmd:FB: ucmd setenv fastboot_buffer ${fdt_addr}
2:141>Okay (0.012s)
2:141>Start Cmd:FB: download -f imx8mp-evk.dtb
2:141>Okay (0.024s)
2:141>Start Cmd:FB: ucmd setenv fastboot_buffer ${initrd_addr}
2:141>Okay (0.011s)
2:141>Start Cmd:FB: download -f fsl-image-mfgtool-initramfs-imx_mfgtools.cpio.zst.u-boot
2:141>Okay (0.624s)
2:141>Start Cmd:FB: acmd ${kboot} ${loadaddr} ${initrd_addr} ${fdt_addr}
2:141>Okay (0.008s)

[Device log]

U-Boot SPL 2021.04-lf_v2021.04+g263b27e076 (Nov 22 2021 - 01:39:23 +0000)
DDRINFO: start DRAM init
DDRINFO: DRAM rate 4000MTS
DDRINFO:ddrphy calibration done
DDRINFO: ddrmix config done
SEC0: RNG instantiated
Normal Boot
WDT: Not found!
Trying to boot from BOOTROM
Find img info 0x&480269a0, size 1032
Need continue download 1024
Download 1593520, Total size 1595152
NOTICE: BL31: v2.4(release):lf-5.10.72-2.2.0-0-g5782363f9
NOTICE: BL31: Built : 12:17:17, Nov 18 2021

U-Boot 2021.04-lf_v2021.04+g263b27e076 (Nov 22 2021 - 01:39:23 +0000)

CPU: i.MX8MP[8] rev1.1 1600 MHz (running at 1200 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 33C
Reset cause: POR
Model: NXP i.MX8MPlus LPDDR4 EVK board
DRAM: 2 GiB
tcpc_init: Can't find bus
setup_typec: tcpc port2 init failed, err=-22
setup_pd_switch: Can't find device id=0x72
TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C1 0x50]
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Fail to setup video link
In: serial
Out: serial
Err: serial
SEC0: RNG instantiated

BuildInfo:
- ATF 5782363

MMC: no card present
Detect USB boot. Will enter fastboot mode!
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address - 0a:1c:79:0d:7b:97

Warning: ethernet@30bf0000 (eth1) using random MAC address - fe:53:ba:8e:22:15
eth0: ethernet@30be0000, eth1: ethernet@30bf0000 [PRIME]
Fastboot: Normal
Boot from USB for mfgtools
*** Warning - Use default environment for mfgtool
s
, using default environment

Run bootcmd_mfg: run mfgtool_args;if iminfo ${initrd_addr}; then if test ${tee}
= yes; then bootm ${tee_addr} ${initrd_addr} ${fdt_addr}; else booti ${loadaddr}
${initrd_addr} ${fdt_addr}; fi; else echo "Run fastboot ..."; fastboot 0; fi;
Hit any key to stop autoboot: 0

## Checking Image at 43800000 ...
Unknown image format!
Run fastboot ...
Detect USB boot. Will enter fastboot mode!
flash target is MMC:1
MMC: no card present
MMC card init failed!
MMC: no card present
** Block device MMC 1 not supported
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Detect USB boot. Will enter fastboot mode!
flash target is MMC:2
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Starting download of 1955600 bytes
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
..............
downloading of 1955600 bytes finished
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
writing to partition 'bootloader'
Initializing 'bootloader'
switch to partitions #1, OK
mmc2(part 1) is current device
Writing 'bootloader'

MMC write: dev # 2, block # 0, count 3820 ... 3820 blocks written: OK
Writing 'bootloader' DONE!
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Detect USB boot. Will enter fastboot mode!
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Detect USB boot. Will enter fastboot mode!
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Detect USB boot. Will enter fastboot mode!
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Detect USB boot. Will enter fastboot mode!
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Detect USB boot. Will enter fastboot mode!
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Detect USB boot. Will enter fastboot mode!
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Starting download of 32121344 bytes
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
..........................................................................
..........................................................................
..........................................................................
.......................
downloading of 32121344 bytes finished
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Detect USB boot. Will enter fastboot mode!
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Starting download of 58085 bytes
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk

downloading of 58085 bytes finished
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Detect USB boot. Will enter fastboot mode!
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Starting download of 12029289 bytes
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
..........................................................................
.................
downloading of 12029289 bytes finished
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
(NULL udevice *): request 00000000bdf1f900 was not queued to ep1in-bulk
Moving Image from 0x40480000 to 0x40600000, end=42550000
## Loading init Ramdisk from Legacy Image at 43800000 ...
Image Name: fsl-image-mfgtool-initramfs-imx8
Created: 2011-04-05 23:00:00 UTC
Image Type: AArch64 Linux RAMDisk Image (uncompressed)
Data Size: 12029225 Bytes = 11.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 43000000
Booting using the fdt blob at 0x43000000
Using Device Tree in place at 0000000043000000, end 00000000430112e4

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.1.22+g66e442bc7fdc (oe-user@oe-host) (aarch64-pok
y-linux-gcc (GCC) 12.2.0, GNU ld (GNU Binutils) 2.40.20230119) #1 SMP PREEMPT Mo
n Jun 12 12:31:27 UTC 2023
[ 0.000000] Machine model: NXP i.MX8MP SOM on AB2
[ 0.000000] efi: UEFI not found.
[ 0.000000] OF: reserved mem: failed to allocate memory for node 'linux,cma':
size 960 MiB
[ 0.000000] Reserved memory: created DMA memory pool at 0x0000000094300000, s
ize 1 MiB
[ 0.000000] OF: reserved mem: initialized node vdev0buffer@94300000, compatib
le id shared-dma-pool
[ 0.000000] NUMA: No NUMA configuration found
[ 0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x00000000bfffffff
]
[ 0.000000] NUMA: NODE_DATA [mem 0xbfbca700-0xbfbccfff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000055ffffff]
[ 0.000000] node 0: [mem 0x0000000058000000-0x00000000923fffff]
[ 0.000000] node 0: [mem 0x0000000092400000-0x00000000943fffff]
[ 0.000000] node 0: [mem 0x0000000094400000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] On node 0, zone DMA: 8192 pages in unavailable ranges
[ 0.000000] cma: Reserved 32 MiB at 0x00000000bba00000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 20 pages/cpu s44520 r8192 d29208 u81920
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Fallback order for Node 0: 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 507904
[ 0.000000] Policy zone: DMA
[ 0.000000] Kernel command line: console=ttymxc1,115200,115200 rdinit=/linuxr
c clk_ignore_unused
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes,
linear)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes,
linear)
[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off
[ 0.000000] Memory: 1914504K/2064384K available (19584K kernel code, 1608K rw
data, 6708K rodata, 3328K init, 644K bss, 117112K reserved, 32768K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jif
fies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 160 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: GICv3 features: 16 PPIs
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000038880000
[ 0.000000] ITS: No ITS available, not enabling LPIs
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles:
0x1d854df40, max_idle_ns: 440795202120 ns
[ 0.000000] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 21990
23255500ns
[ 0.000460] Console: colour dummy device 80x25
[ 0.000518] Calibrating delay loop (skipped), value calculated using timer fr
equency.. 16.00 BogoMIPS (lpj=32000)
[ 0.000528] pid_max: default: 32768 minimum: 301
[ 0.000579] LSM: Security Framework initializing
[ 0.000660] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, line
ar)
[ 0.000671] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes,
linear)
[ 0.001940] cblist_init_generic: Setting adjustable number of callback queues
.
[ 0.001951] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.002019] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.002172] rcu: Hierarchical SRCU implementation.
[ 0.002175] rcu: Max phase no-delay instances is 1000.
[ 0.003615] EFI services will not be available.
[ 0.003811] smp: Bringing up secondary CPUs ...
[ 0.004281] Detected VIPT I-cache on CPU1
[ 0.004356] GICv3: CPU1: found redistributor 1 region 0:0x00000000388a0000
[ 0.004390] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.004864] Detected VIPT I-cache on CPU2
[ 0.004925] GICv3: CPU2: found redistributor 2 region 0:0x00000000388c0000
[ 0.004943] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.005374] Detected VIPT I-cache on CPU3
[ 0.005437] GICv3: CPU3: found redistributor 3 region 0:0x00000000388e0000
[ 0.005454] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.005512] smp: Brought up 1 node, 4 CPUs
[ 0.005520] SMP: Total of 4 processors activated.
[ 0.005524] CPU features: detected: 32-bit EL0 Support
[ 0.005527] CPU features: detected: 32-bit EL1 Support
[ 0.005530] CPU features: detected: CRC32 instructions
[ 0.005584] CPU: All CPU(s) started at EL2
[ 0.005602] alternatives: applying system-wide alternatives
[ 0.007132] devtmpfs: initialized
[ 0.015380] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma
x_idle_ns: 7645041785100000 ns
[ 0.015400] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.016407] pinctrl core: initialized pinctrl subsystem
[ 0.019052] DMI not present or invalid.
[ 0.019617] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.020616] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[ 0.020863] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allo
cations
[ 0.021040] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic al
locations
[ 0.021089] audit: initializing netlink subsys (disabled)
[ 0.021209] audit: type=2000 audit(0.020:1): state=initialized audit_enabled=
0 res=1
[ 0.021700] thermal_sys: Registered thermal governor 'step_wise'
[ 0.021704] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.021736] cpuidle: using governor menu
[ 0.021915] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.021992] ASID allocator initialised with 65536 entries
[ 0.023104] Serial: AMBA PL011 UART driver
[ 0.023166] imx mu driver is registered.
[ 0.023187] imx rpmsg driver is registered.
[ 0.031671] imx8mp-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver
[ 0.043620] platform 32fc6000.lcd-controller: Fixed dependency cycle(s) with
/soc@0/bus@30c00000/hdmi@32fd8000
[ 0.048582] KASLR disabled due to lack of seed
[ 0.067197] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.067206] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page
[ 0.067211] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.067214] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page
[ 0.067220] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.067225] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page
[ 0.067231] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.067235] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page
[ 0.069040] ACPI: Interpreter disabled.
[ 0.069697] iommu: Default domain type: Translated
[ 0.069701] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.069962] SCSI subsystem initialized
[ 0.070255] usbcore: registered new interface driver usbfs
[ 0.070288] usbcore: registered new interface driver hub
[ 0.070315] usbcore: registered new device driver usb
[ 0.071450] mc: Linux media interface: v0.10
[ 0.071481] videodev: Linux video capture interface: v2.00
[ 0.071544] pps_core: LinuxPPS API ver. 1 registered
[ 0.071547] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome
tti <giometti@linux.it>
[ 0.071560] PTP clock support registered
[ 0.071711] EDAC MC: Ver: 3.0.0
[ 0.072800] FPGA manager framework
[ 0.072872] Advanced Linux Sound Architecture Driver Initialized.
[ 0.073386] Bluetooth: Core ver 2.22
[ 0.073412] NET: Registered PF_BLUETOOTH protocol family
[ 0.073416] Bluetooth: HCI device and connection manager initialized
[ 0.073423] Bluetooth: HCI socket layer initialized
[ 0.073427] Bluetooth: L2CAP socket layer initialized
[ 0.073437] Bluetooth: SCO socket layer initialized
[ 0.073765] vgaarb: loaded
[ 0.074186] clocksource: Switched to clocksource arch_sys_counter
[ 0.074356] VFS: Disk quotas dquot_6.6.0
[ 0.074394] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.074545] pnp: PnP ACPI: disabled
[ 0.081198] NET: Registered PF_INET protocol family
[ 0.081360] IP idents hash table entries: 32768 (order: 6, 262144 bytes, line
ar)
[ 0.082894] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 1638
4 bytes, linear)
[ 0.082945] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes,
linear)
[ 0.082958] TCP established hash table entries: 16384 (order: 5, 131072 bytes
, linear)
[ 0.083070] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linea
r)
[ 0.083486] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.083568] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.083616] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.083758] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.084073] RPC: Registered named UNIX socket transport module.
[ 0.084077] RPC: Registered udp transport module.
[ 0.084080] RPC: Registered tcp transport module.
[ 0.084082] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.084791] PCI: CLS 0 bytes, default 64
[ 0.084991] Unpacking initramfs...
[ 0.094716] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counte
rs available
[ 0.095476] kvm [1]: IPA Size Limit: 40 bits
[ 0.096654] kvm [1]: GICv3: no GICV resource entry
[ 0.096662] kvm [1]: disabling GICv2 emulation
[ 0.096675] kvm [1]: GIC system register CPU interface enabled
[ 0.096814] kvm [1]: vgic interrupt IRQ9
[ 0.096896] kvm [1]: Hyp mode initialized successfully
[ 0.098054] Initialise system trusted keyrings
[ 0.098258] workingset: timestamp_bits=42 max_order=19 bucket_order=0
[ 0.104153] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.104792] NFS: Registering the id_resolver key type
[ 0.104826] Key type id_resolver registered
[ 0.104829] Key type id_legacy registered
[ 0.104905] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.104910] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering
...
[ 0.104932] jffs2: version 2.2. (NAND) 짤 2001-2006 Red Hat, Inc.
[ 0.105261] 9p: Installing v9fs 9p2000 file system support
[ 0.141387] Key type asymmetric registered
[ 0.141401] Asymmetric key parser 'x509' registered
[ 0.141477] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2
43)
[ 0.141483] io scheduler mq-deadline registered
[ 0.141487] io scheduler kyber registered
[ 0.148851] EINJ: ACPI disabled.
[ 0.161365] mxs-dma 33000000.dma-apbh: initialized
[ 0.168963] SoC: i.MX8MP revision 1.1
[ 0.172855] Bus freq driver module loaded
[ 0.179316] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.181971] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 17, base_baud
= 5000000) is a IMX
[ 0.182652] 30880000.serial: ttymxc2 at MMIO 0x30880000 (irq = 18, base_baud
= 5000000) is a IMX
[ 0.183146] 30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 19, base_baud
= 1500000) is a IMX
[ 0.707916] Freeing initrd memory: 11740K
[ 0.709691] printk: console [ttymxc1] enabled
[ 0.715331] imx-sdma 30bd0000.dma-controller: Direct firmware load for imx/sd
ma/sdma-imx7d.bin failed with error -2
[ 1.311999] imx-sdma 30bd0000.dma-controller: Falling back to sysfs fallback
for: imx/sdma/sdma-imx7d.bin
[ 1.316622] loop: module loaded
[ 1.326284] megasas: 07.719.03.00-rc1
[ 1.335318] spi-nor spi0.0: n25q256ax1 (32768 Kbytes)
[ 1.344800] tun: Universal TUN/TAP device driver, 1.6
[ 1.350906] thunder_xcv, ver 1.0
[ 1.354167] thunder_bgx, ver 1.0
[ 1.357439] nicpf, ver 1.0
[ 1.362423] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - versio
n
[ 1.369658] hns3: Copyright (c) 2017 Huawei Corporation.
[ 1.375024] hclge is initializing
[ 1.378362] e1000: Intel(R) PRO/1000 Network Driver
[ 1.383247] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 1.389032] e1000e: Intel(R) PRO/1000 Network Driver
[ 1.394005] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.399971] igb: Intel(R) Gigabit Ethernet Network Driver
[ 1.405410] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 1.411028] igbvf: Intel(R) Gigabit Virtual Function Network Driver
[ 1.417308] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 1.423433] sky2: driver version 1.30
[ 1.427754] usbcore: registered new interface driver r8152
[ 1.433511] VFIO - User Level meta-driver version: 0.3
[ 1.442420] usbcore: registered new interface driver uas
[ 1.447785] usbcore: registered new interface driver usb-storage
[ 1.453852] usbcore: registered new interface driver usbserial_generic
[ 1.460413] usbserial: USB Serial support registered for generic
[ 1.466452] usbcore: registered new interface driver ftdi_sio
[ 1.472220] usbserial: USB Serial support registered for FTDI USB Serial Devi
ce
[ 1.479563] usbcore: registered new interface driver usb_serial_simple
[ 1.486116] usbserial: USB Serial support registered for carelink
[ 1.492229] usbserial: USB Serial support registered for zio
[ 1.497907] usbserial: USB Serial support registered for funsoft
[ 1.503933] usbserial: USB Serial support registered for flashloader
[ 1.510303] usbserial: USB Serial support registered for google
[ 1.516243] usbserial: USB Serial support registered for libtransistor
[ 1.522789] usbserial: USB Serial support registered for vivopay
[ 1.528820] usbserial: USB Serial support registered for moto_modem
[ 1.535109] usbserial: USB Serial support registered for motorola_tetra
[ 1.541743] usbserial: USB Serial support registered for nokia
[ 1.547593] usbserial: USB Serial support registered for novatel_gps
[ 1.553969] usbserial: USB Serial support registered for hp4x
[ 1.559736] usbserial: USB Serial support registered for suunto
[ 1.565676] usbserial: USB Serial support registered for siemens_mpi
[ 1.572063] usbcore: registered new interface driver usb_ehset_test
[ 1.581333] input: 30370000.snvs:snvs-powerkey as /devices/platform/soc@0/300
00000.bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0
[ 1.596044] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc0
[ 1.602264] snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to 1970-
01-01T00:00:00 UTC (0)
[ 1.611469] i2c_dev: i2c /dev entries driver
[ 1.620744] Bluetooth: HCI UART driver ver 2.3
[ 1.625213] Bluetooth: HCI UART protocol H4 registered
[ 1.630363] Bluetooth: HCI UART protocol BCSP registered
[ 1.635698] Bluetooth: HCI UART protocol LL registered
[ 1.640844] Bluetooth: HCI UART protocol ATH3K registered
[ 1.646265] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 1.652632] Bluetooth: HCI UART protocol Broadcom registered
[ 1.658322] Bluetooth: HCI UART protocol QCA registered
[ 1.663746] EDAC MC: ECC not enabled
[ 1.668770] sdhci: Secure Digital Host Controller Interface driver
[ 1.674972] sdhci: Copyright(c) Pierre Ossman
[ 1.680136] Synopsys Designware Multimedia Card Interface Driver
[ 1.686884] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.695138] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.702048] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[ 1.708998] usbcore: registered new interface driver usbhid
[ 1.714584] usbhid: USB HID core driver
[ 1.723363] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA
[ 1.723520] cs_system_cfg: CoreSight Configuration manager initialised
[ 1.725509] mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA
[ 1.746016] optee: probing for conduit method.
[ 1.750504] optee: revision 3.15 (c939619d)
[ 1.751382] optee: dynamic shared memory is enabled
[ 1.760852] optee: initialized driver
[ 1.767407] Galcore version 6.4.11.p1.658245
[ 1.790409] [drm] Initialized vivante 1.0.0 20170808 for 40000000.mix_gpu_ml
on minor 0
[ 1.800170] hantrodec 0 : module inserted. Major = 510
[ 1.805877] hantrodec 1 : module inserted. Major = 510
[ 1.812639] hantroenc: HW at base <0000000038320000> with ID <0x80006200>
[ 1.819580] hx280enc: module inserted. Major <509>
[ 1.827031] NET: Registered PF_LLC protocol family
[ 1.833179] NET: Registered PF_INET6 protocol family
[ 1.839922] Segment Routing with IPv6
[ 1.843645] In-situ OAM (IOAM) with IPv6
[ 1.847659] NET: Registered PF_PACKET protocol family
[ 1.852756] bridge: filtering via arp/ip/ip6tables is no longer available by
default. Update your scripts to load br_netfilter if you need this.
[ 1.866677] Bluetooth: RFCOMM TTY layer initialized
[ 1.871597] Bluetooth: RFCOMM socket layer initialized
[ 1.876774] Bluetooth: RFCOMM ver 1.11
[ 1.880554] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.885904] Bluetooth: BNEP filters: protocol multicast
[ 1.891158] Bluetooth: BNEP socket layer initialized
[ 1.896139] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.902079] Bluetooth: HIDP socket layer initialized
[ 1.908013] 8021q: 802.1Q VLAN Support v1.8
[ 1.912241] lib80211: common routines for IEEE802.11 drivers
[ 1.918036] 9pnet: Installing 9P2000 support
[ 1.922449] Key type dns_resolver registered
[ 1.927445] registered taskstats version 1
[ 1.931591] Loading compiled-in X.509 certificates
[ 1.931885] mmc2: new HS400 Enhanced strobe MMC card at address 0001
[ 1.943540] mmcblk2: mmc2:0001 DG4016 14.7 GiB
[ 1.949929] mmcblk2boot0: mmc2:0001 DG4016 4.00 MiB
[ 1.955984] mmcblk2boot1: mmc2:0001 DG4016 4.00 MiB
[ 1.959944] mmc0: new ultra high speed SDR104 SDIO card at address 0001
[ 1.962007] mmcblk2rpmb: mmc2:0001 DG4016 4.00 MiB, chardev (234:0)
[ 1.978372] nxp-pca9450 0-0025: pca9450bc probed.
[ 1.983188] i2c i2c-0: IMX I2C adapter registered
[ 1.989071] pca953x 1-0020: supply vcc not found, using dummy regulator
[ 1.995788] pca953x 1-0020: using no AI
[ 1.999962] pca953x 1-0020: failed writing register
[ 2.005220] pca953x 1-0021: supply vcc not found, using dummy regulator
[ 2.011933] pca953x 1-0021: using no AI
[ 2.016095] pca953x 1-0021: failed writing register
[ 2.021189] i2c i2c-1: IMX I2C adapter registered
[ 2.027018] pca953x 2-0020: supply vcc not found, using dummy regulator
[ 2.033738] pca953x 2-0020: using no AI
[ 2.038130] pca953x 2-0020: failed writing register
[ 2.044081] i2c i2c-2: IMX I2C adapter registered
[ 2.059009] dwhdmi-imx 32fd8000.hdmi: Detected HDMI TX controller v2.13a with
HDCP (samsung_dw_hdmi_phy2)
[ 2.070647] dwhdmi-imx 32fd8000.hdmi: registered DesignWare HDMI I2C bus driv
er
[ 2.082496] imx-drm display-subsystem: bound imx-lcdifv3-crtc.0 (ops lcdifv3_
crtc_ops)
[ 2.090483] imx-drm display-subsystem: bound 32fd8000.hdmi (ops dw_hdmi_imx_o
ps)
[ 2.098786] [drm] Initialized imx-drm 1.0.0 20120507 for display-subsystem on
minor 1
[ 2.106692] imx-drm display-subsystem: [drm] Cannot find any crtc or sizes
[ 2.117393] imx-dwmac 30bf0000.ethernet: IRQ eth_lpi not found
[ 2.124489] imx-dwmac 30bf0000.ethernet: User ID: 0x10, Synopsys ID: 0x51
[ 2.131311] imx-dwmac 30bf0000.ethernet: DWMAC4/5
[ 2.136115] imx-dwmac 30bf0000.ethernet: DMA HW capability register supported
[ 2.143258] imx-dwmac 30bf0000.ethernet: RX Checksum Offload Engine supported
[ 2.150401] imx-dwmac 30bf0000.ethernet: TX Checksum insertion supported
[ 2.157110] imx-dwmac 30bf0000.ethernet: Wake-Up On Lan supported
[ 2.163259] imx-dwmac 30bf0000.ethernet: Enable RX Mitigation via HW Watchdog
Timer
[ 2.170938] imx-dwmac 30bf0000.ethernet: device MAC address a6:03:10:dd:59:f7
[ 2.178084] imx-dwmac 30bf0000.ethernet: Enabled L3L4 Flow TC (entries=8)
[ 2.184884] imx-dwmac 30bf0000.ethernet: Enabled RFS Flow TC (entries=10)
[ 2.191686] imx-dwmac 30bf0000.ethernet: Enabling HW TC (entries=256, max_off
=256)
[ 2.199272] imx-dwmac 30bf0000.ethernet: Using 34/40 bits DMA host/device wid
th
[ 2.214373] imx-cpufreq-dt imx-cpufreq-dt: cpu speed grade 7 mkt segment 2 su
pported-hw 0x80 0x4
[ 2.224119] Hot alarm is canceled. GPU3D clock will return to 64/64
[ 2.233560] sdhci-esdhc-imx 30b50000.mmc: Got CD GPIO
[ 2.235471] cfg80211: Loading compiled-in X.509 certificates for regulatory d
atabase
[ 2.251204] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 2.257837] platform regulatory.0: Direct firmware load for regulatory.db fai
led with error -2
[ 2.266467] platform regulatory.0: Falling back to sysfs fallback for: regula
tory.db
[ 2.266507] clk: Not disabling unused clocks
[ 2.274368] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA
[ 2.278515] ALSA device list:
[ 2.288511] No soundcards found.
[ 2.293287] Freeing unused kernel memory: 3328K
[ 2.314256] Run /linuxrc as init process
No udc Available!
No udc Available!
No udc Available!
[ 12.515257] platform gpio-reset: deferred probe pending
No udc Available!
No udc Available!
No udc Available!
No udc Available!

[dskim2]

I used new uuu tool please below uuu tool version

uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.5.21-0-g1f42172

[jogt]

did you find any solution?

[xjy198903]

Hi,
Configure usb as host mode in the kernel and try.

[jogt]

In my case, as I compiled a modified kernel and rootfs using buildroot. I just had missed adding the bash package to run "imx-uuu-init" after init. Now, everything is working on my end.

[xjy198903]

I'm also experiencing this problem, how can I solve it