How do I configure SPLL CLK?

[jinsheng20]

[Robin_Shen · Accepted solution]

Hi jinsheng20,

The Phase-locked loop (PLL) is not available for the S32K11x product series. That is why you cannot configure it.

Best Regards,
Robin
-------------------------------------------------------------------------------
Note:
- If this post answers your question, please click the "Mark Correct" button. Thank you!

- We are following threads for 7 weeks after the last post, later replies are ignored
Please open a new thread and refer to the closed one, if you have a related question at a later point in time.
-------------------------------------------------------------------------------

[1090097669]

Hi Robin,

according to Datasheert,the  and the current consumption it is 21mA,and following Code which the current consumption it is 4mA,it should be less than 1mA.

how to further reduce the current consumption by the controller?
 And also how to disable the clock monitors?
And if possible also let me know how to come to normal RUN mode through CAN

Please point out my configuration errors or missing areas

void power_cp_wakeup_set(void)/*E5*/

{

PINS_DRV_SetPinIntSel(GPIO_CP_WAKE_PORT,GPIO_CP_WAKE_PIN,PORT_INT_RISING_EDGE);

}

void init_NVIC(void)

{

power_cp_wakeup_set();

INT_SYS_ClearPending(PORTE_IRQn);

INT_SYS_SetPriority(PORTE_IRQn, 0);

// PORTE_interrupt

S32_NVIC-> ICPR [1] = (1 <<(63%32));

S32_NVIC-> ISER [1] = (1 <<(63%32));

S32_NVIC-> IP [63] = 0x10;

PORTE-> DFER |= (1 << 5);

}

void Power_RUN_to_STOP (void)

{

#if 0

/* Set the SLEEPDEEP bit to enable deep sleep mode (STOP) */

S32_SCB->SCR |= S32_SCB_SCR_SLEEPDEEP_MASK;

/*select stop mode*/

SMC->PMCTRL = SMC_PMCTRL_STOPM(0b00);

SMC->STOPCTRL = SMC_STOPCTRL_STOPO(0b01);

if(SMC->PMSTAT == 0x01)

{

asm("WFI");

}

#else

/* Disable the JTAG port pins */

/* Disable Adc Pins */

PMC->REGSC |= PMC_REGSC_BIASEN(1); // [1] CLKBIASDIS = 1 In VLPS mode, the bias current for SIRC, FIRC, PLL is disabled

/* Disable the Fosc and Sosc from chip*/

SCG->FIRCCSR = SCG_FIRCCSR_FIRCEN(0);

while(SCG->FIRCCSR & (1 << 24));

SCG->SOSCCSR = SCG_SOSCCSR_SOSCEN(0);

S32_SCB->SCR |= S32_SCB_SCR_SLEEPDEEP_MASK|0x2; /* allow deep sleep mode0 */

SMC->PMPROT = SMC_PMPROT_AVLP(1); /* allow very low power mode*/

SMC->PMCTRL = SMC_PMCTRL_STOPM(2);

if(SMC->PMSTAT == 0x01)

{

asm("WFI");

}

#endif

}

void power_set_mode(POWER_SYS_TYPE mod)
{
if(mod == POWER_SYS_SLEEP)
{

init_NVIC();
//power_can_wakeup_set();
Power_RUN_to_STOP();
}
}

Regards,

Katrinal