I got a new FRDM-KL26z yesterday, and followed the Quick Start Guide to test it.
But when I set it into Bootloader Mode, it always in the Bootloader mode.
Even I tried to copy MSD-DEBUG-FRDM-KL26Z_Pemicro_v114.SDA or BOOTUPDATEAPP_Pemicro_v111.SDA through command line.
There is only a BOOTLOADER disk shown in my Windows7 machine.
The SDA_INFO shows:
Board Name is: FRDM-KL26Z
MicroBoot Kernel Version is: 1.05
Bootloader Version is: 1.09
Application Version is: 0.00
DUID is: A5733938-8F1281C7-3737E815-B779E678
EUID is: ADF1A239-20388745-18390A12-958268D6
TUID is: 74823938-473281CF-378C980C-B990E678
TOA is: 86B6E505-2E89E395-1D79DB3C-4DDEE7A7
TOA2 is: 86B6E505-B6F4FCE7-8B5E2BB1-1EE08095
SUID is: 86B6E505-6D47969C-37239804-8003EC65
Are there anything wrong about this board?
Thanks,
Solved! Go to Solution.
Only the BOOTLOADER disk is shown? What happen when you drag and drop the BOOTUPDATEAPP_Pemicro_v111.SDA file into the BOOTLOADER disk?
Can you please confirm the same behavior in another computer?
Regards,
Adrian
Hi Adrain,
Thanks for your reply.
But I still cannot update the bootloader, because the LED always shows "2 seconds off followed by 8 rapid on/off blinks" even I pressed the reset button when I power-on the board.
Thanks,
Henry Xin
Only the BOOTLOADER disk is shown? What happen when you drag and drop the BOOTUPDATEAPP_Pemicro_v111.SDA file into the BOOTLOADER disk?
Can you please confirm the same behavior in another computer?
Regards,
Adrian
Thanks, It works when I use my old IBM T61 laptop. Is it possible the difference about the USB host in two computers. They both have Windows7 Installed.
Best Regards
Henry
This is the new SDA_INFO:
Your Hardware Information | |
Board Name is: FRDM-KL26Z MicroBoot Kernel Version is: 1.05 Bootloader Version is: 1.11 Installed Application: PEMicro FRDM-KL26Z Mass Storage/Debug App Application Version is: 1.14 DUID is: A5733938-8F1281C7-3737E815-B779E678 EUID is: ADF1A239-20388745-18390A12-958268D6 TUID is: 74823938-473281CF-378C980C-B990E678 TOA is: 86B6E505-2E89E395-1D79DB3C-4DDEE7A7 TOA2 is: 86B6E505-B6F4FCE7-8B5E2BB1-1EE08095 SUID is: 86B6E505-6D47969C-37239804-8003EC65 |
Hi,
I am not sure about the way that Windows 7 manage the different versions of this firmware. But now you can use the board without any problems, I mean can you debug or load a binary to the board the first computer you tried?
Hope this information can help you.
Best Regards,
Adrian Sanchez Cano
Technical Support Engineer
-----------------------------------------------------------------------------------------------------------------------
:smileyinfo:Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------
Hi Adrian,
The pre-compile binary file works well in my board now.
Thanks for your help.
Henry Xin
When I drag and drop the BOOTUPDATEAPP_Pemicro_v111.SDA file into BOOTLOADER disk, there is nothing wrong in my windows7 as following:
There is not another computer on hand now, I will try it later.
Thanks,
Henry
I think there is an error in bootloader mode, because the LED shows this way:
Bootloader Error 2 seconds off followed by 8 rapid on/off blinks
Hi,
Please try to update the firmware for the version v114, here you can find a complete step by step tutorial to accomplish this by colleague Erich Styger:
You need to use the files for the FRDM-KL26
Hope this information can help you.
Best Regards,
Adrian Sanchez Cano
Technical Support Engineer
-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------