1 GND Ground9 GND Ground11 BKGND Background13 EXTAL Crystal oscillator input14 CLKO Programmable Clock Output (default: 32,768 kHz)17 GND Ground24 Vcc Modem voltage regulators' input25 GND Ground26 Vcc Modem voltage regulators' input27 RESET MCU reset. Active low31 GND Ground
LOL, one year later... Still fighting against this one
Actually, I was able to wire everything up to a state on the attached diagram. Then I launch hiwave.exe, go to Component=> Set Connection => HCS08 => HCS08 Open Source BDM, and then USB ACT LED blinks on my BDM and the Command window displays the following:
NO CONNECTIONLoading Target ...SETCOMM DRIVER NOPROTOCOL NOPERIODICALSETCOMM COMPORT NONETARGET SECURED? NO TARGET CONNECTED?Communication settings:SETCOMM DRIVER PROTOCOL NOPERIODICALCommunication settings:SETCOMM COMPORT LPT "OSBDM #1"GDI: DiGdiClose(TRUE)Communication settings:SETCOMM DRIVER PROTOCOL NOPERIODICALLoading Communication DLL ==> C:\Program Files\Freescale\CodeWarrior for Microcontrollers V6.2\prog\gdi\OSBDM_S08.dllGDI: DiGdiOpen()==> DI_OKGDI: DiGdiVersion()==> DI_ERR_NOTSUPPORTEDGDI: DiGdiAddCallBack(8192)==> DI_OKGDI: DiGdiAddCallBack(16384)==> DI_OKGDI: DiCommGetAcceptableSettings()==> 5GDI: DiCommGetAcceptableSettings()==> 0GDI: DiCommGetAcceptableSettings()==> 5Communication settings:SETCOMM COMPORT LPT "OSBDM #1"Initializing STARTUP command file:CMDFILE STARTUP ON "startup.cmd"Initializing RESET command file:CMDFILE RESET ON "reset.cmd"Initializing PRELOAD command file:CMDFILE PRELOAD ON "preload.cmd"Initializing POSTLOAD command file:CMDFILE POSTLOAD ON "postload.cmd"GDI: DiGdiInitIO()GDI DLL called: DI_CB_MTWKS_EXTENSION_Callback(MTWKS_CB_DISPLAYLINE)TARGET SECURED? NO TARGET CONNECTED?==> DI_ERR_FATALInitializing STARTUP command file:CMDFILE STARTUP ON "startup.cmd"Initializing RESET command file:CMDFILE RESET ON "reset.cmd"Initializing PRELOAD command file:CMDFILE PRELOAD ON "preload.cmd"Initializing POSTLOAD command file:CMDFILE POSTLOAD ON "postload.cmd"GDI: DiDirectAddMenuItem()==> DI_OKNo Link To Target
OK, now what?
I am not familiar with this device, but it sounds like the chip is not running.
check your clocking, since the bdm does not supply a clock.
Also, that chip has more than one gnd and vcc. Since you don't show them connected, are you connecting them?
Could you wire all the stuff together?
Could you finish your project with PAN4555?
I'm doing the same than u and have the same doubts like you.
Do you have your stuff about this anymore? Would you may send me your schematic and maybe a primitive code?
daniel.schiller_AT_gmail.com (@ instead of _AT_ )
thank u very much!
I've 5 of this PAN4555 chips and i only want to communicate two of them. For example pressing a button on the first and turn a led on the second chip.
Did you solve your problem of "Error Loading Diagnostic Algorithm to target"? I understand this is an old post, but I am experiencing this problem as well. I have three boards built up in parrallel one works two suffer from loading Diagnostic Algorithm. They are not identical boards but very similiar a few farads of difference and trace correction not identical. I did think my dbm and rst lines were a bit noisy, but have since cleaned up the lines.
Retrieving data ...