Wireless MCU中的主题 how to add a point in jn-an-1218-zigbee-3-0-light-bulb

how to add a point in jn-an-1218-zigbee-3-0-light-bulb

1948396491 — Sat, 20 Jul 2019 07:16:41 GMT

Hello, I have a problem now, which means I am confused.A problem arose when I added a new endpoint to the ExtendedColorLight routine of jn-an-1218-zigbee-3-0-light-bulb.After completing the configuration in files app_gp.zpscfg and zcl_options.h, and then completing the registration of defining device type and endpoint in files app_extendedcolorlight.c and.However, after I blocked the registration of defined device type and endpoint in app_extendedcolorlight.c and.h files, the file was successfully recompiled, and the data and initialization data were output in Terminal again.Now I'm depressed why is that? I used to add new endpoints like this?

Re: how to add a point in jn-an-1218-zigbee-3-0-light-bulb

mario_castaneda — Mon, 22 Jul 2019 16:49:47 GMT

Hi,

Could you please look at the next community post?

https://community.nxp.com/thread/507619

Please let me know if you have issues adding a new endpoint.

Regards,

Mario

Re: how to add a point in jn-an-1218-zigbee-3-0-light-bulb

1948396491 — Tue, 23 Jul 2019 00:43:04 GMT

Hello, thanks for your reply!I just added the new endpoint in the extendedcolorlight routine of jn-an-1218-zigbee-3.0-light-bulb routine according to the document provided by the government. After the addition, there was no error in the compilation, but where I printed the output, there was no output, and there was no initial output. I don't know why.

Re: how to add a point in jn-an-1218-zigbee-3-0-light-bulb

mario_castaneda — Tue, 23 Jul 2019 18:07:44 GMT

Hi,

I am not sure if I am understanding your issue.

Could you please try to open the terminal in an external software? Teraterm, putty

Regards,

Mario

Re: how to add a point in jn-an-1218-zigbee-3-0-light-bulb

1948396491 — Wed, 24 Jul 2019 00:34:50 GMT

Hello, I opened a terminal in the last picture above, which is also marked.The other pictures are the code I added the endpoint to.My problem is that after adding a new endpoint to the source code above, I find that the terminal has no output of any information, including initialization information.

Re: how to add a point in jn-an-1218-zigbee-3-0-light-bulb

mario_castaneda — Wed, 24 Jul 2019 17:26:03 GMT

Hi,

Could you please comment the next code app_zlc_light_task.c?

           /* else if(E_ZCL_RESTORE_DEFAULT_REPORT_CONFIGURATION == psEvent->eZCL_Status)
            {

                vRestoreDefaultRecord(app_u8GetDeviceEndpoint(),
                                psEvent->psClusterInstance->psClusterDefinition->u16ClusterEnum,
                                psAttributeReportingRecord);
            } */‍‍‍‍‍‍‍

Also, could you please send an active request from the coordinator and wait for the response?

Regards,

Mario

Re: how to add a point in jn-an-1218-zigbee-3-0-light-bulb

1948396491 — Thu, 25 Jul 2019 01:31:28 GMT

Hello, thank you very much for your reply. According to what you said, I blocked that piece of code. After successful compilation, it will still be the same as before.The terminal outputs nothing, so it can't get into the network, and there's no way to send a request through the coordinator.Now I have a request, hope you can help me, can you help me to do a test, in Jacqueline Nottingham - AN - 1218 - zigbee - 3.0 - light bulbs - the ExtendedColorLight source a new growth point, test whether the new endpoint is available, if you can use this endpoint, there is a problem that because this is my code, please share your new endpoint code.If your newly added endpoint doesn't work, you know where my problem lies.In addition, I did not find in the source code where the event information of Color Cluster was received and processed.Do you know where it is?

Re: how to add a point in jn-an-1218-zigbee-3-0-light-bulb

1948396491 — Thu, 25 Jul 2019 01:37:15 GMT

It occurred to me that I had another problem, and the problem was that while enddevice was sleeping, other devices were sending messages to this enddevice, how did this enddevice wake up and receive this message, how did this code do that?

Re: how to add a point in jn-an-1218-zigbee-3-0-light-bulb

mario_castaneda — Thu, 25 Jul 2019 01:48:02 GMT

Hi,

When the end device wakes up, it sends a data request, then the coordinator will send an ack, but with the frame pending flag set. The device will wait for the data.

I am checking your other question.

Regards,

Mario

Re: how to add a point in jn-an-1218-zigbee-3-0-light-bulb

1948396491 — Thu, 25 Jul 2019 02:53:48 GMT

So you're saying that after we have to manually wake up the enddevice, the enddevice will poll the parent, and if it has data, it will receive data, and if it doesn't, it will go back to sleep?Can I get the device into low-power mode without having to wake it up manually?This means that I now want the device to go into low-power mode (sleep mode) when there is no message, and when there is a message, the device will automatically wake up and receive the message.Can it be done?How can I do that? How can I do that?Please guide.

Re: how to add a point in jn-an-1218-zigbee-3-0-light-bulb

mario_castaneda — Wed, 31 Jul 2019 03:07:31 GMT

Hi,

It will go back to sleep? Can I get the device into low-power mode without having to wake it up manually?

Yes, the device will sleep after that. Please look at the JN-AN-1229 sleep end device.

I ran some test by my side adding an endpoint. I sent a simple descriptor request to the endpoint 2.

Regards,

Mario

Re: how to add a point in jn-an-1218-zigbee-3-0-light-bulb

1948396491 — Wed, 31 Jul 2019 03:13:58 GMT

Thank you for your reply.Strange, then, why can't I add endpoints.Can you share your test code for adding endpoints with me?

Re: how to add a point in jn-an-1218-zigbee-3-0-light-bulb

mario_castaneda — Wed, 31 Jul 2019 16:47:27 GMT

Hi,

Please see the files that I modified. See my comments [MC]

Regards,

Mario