topic Videos testing out Freescale Cup kit in University Programs https://community.nxp.com/t5/University-Programs/Videos-testing-out-Freescale-Cup-kit/m-p/274231#M177 <HTML><HEAD></HEAD><BODY><P>Couple of new videos.</P><P></P><P>This time I am running the FRDM-TFC library demo code written by Eli Hughes without any change at all-- successfully on my car.</P><P></P><P>I have had the 0 ohm R24 res replaced with a higher one thanks to the soldering skills of David DiCarlo!</P><P></P><P>The first video highlights demo modes 0 through 3:</P><P></P><P><A href="https://www.youtube.com/watch?v=ttrPzk_6K9g" title="https://www.youtube.com/watch?v=ttrPzk_6K9g">Car demos - YouTube</A></P><P></P><P>Demo 0- test buttons and switches</P><P>Demo 1- test servo</P><P>Demo 2- test motors</P><P></P><P>Second, I was able to get my little o-scope (<A href="http://www.gabotronics.com/development-boards/xmega-xprotolab.htm">xprotolab</A>) to capture the camera analog out-- here:</P><P></P><P><A href="https://www.youtube.com/watch?v=c4M_7pOCWi0" title="https://www.youtube.com/watch?v=c4M_7pOCWi0">Camera testing - YouTube</A></P><P></P><P></P><P>No major coding done but I understand the library and ports on the boards much better now.&nbsp;&nbsp; Still haven't resolved the 'whining' apparent when I enable the H-bridge but I will try a few things this week-- it is possible it is harmless.</P><P></P><P>Next steps, buffering camera data then on to control loops!</P><P></P><P>Daniel</P></BODY></HTML> Mon, 26 Aug 2013 03:03:07 GMT danielhadad 2013-08-26T03:03:07Z Videos testing out Freescale Cup kit https://community.nxp.com/t5/University-Programs/Videos-testing-out-Freescale-Cup-kit/m-p/274231#M177 <HTML><HEAD></HEAD><BODY><P>Couple of new videos.</P><P></P><P>This time I am running the FRDM-TFC library demo code written by Eli Hughes without any change at all-- successfully on my car.</P><P></P><P>I have had the 0 ohm R24 res replaced with a higher one thanks to the soldering skills of David DiCarlo!</P><P></P><P>The first video highlights demo modes 0 through 3:</P><P></P><P><A href="https://www.youtube.com/watch?v=ttrPzk_6K9g" title="https://www.youtube.com/watch?v=ttrPzk_6K9g">Car demos - YouTube</A></P><P></P><P>Demo 0- test buttons and switches</P><P>Demo 1- test servo</P><P>Demo 2- test motors</P><P></P><P>Second, I was able to get my little o-scope (<A href="http://www.gabotronics.com/development-boards/xmega-xprotolab.htm">xprotolab</A>) to capture the camera analog out-- here:</P><P></P><P><A href="https://www.youtube.com/watch?v=c4M_7pOCWi0" title="https://www.youtube.com/watch?v=c4M_7pOCWi0">Camera testing - YouTube</A></P><P></P><P></P><P>No major coding done but I understand the library and ports on the boards much better now.&nbsp;&nbsp; Still haven't resolved the 'whining' apparent when I enable the H-bridge but I will try a few things this week-- it is possible it is harmless.</P><P></P><P>Next steps, buffering camera data then on to control loops!</P><P></P><P>Daniel</P></BODY></HTML> Mon, 26 Aug 2013 03:03:07 GMT https://community.nxp.com/t5/University-Programs/Videos-testing-out-Freescale-Cup-kit/m-p/274231#M177 danielhadad 2013-08-26T03:03:07Z Re: Couple of new videos... https://community.nxp.com/t5/University-Programs/Videos-testing-out-Freescale-Cup-kit/m-p/274232#M178 <HTML><HEAD></HEAD><BODY><P>Oh, I was also able to get the serial port working while code was running so I could get some dynamic feedback.</P></BODY></HTML> Mon, 26 Aug 2013 03:12:55 GMT https://community.nxp.com/t5/University-Programs/Videos-testing-out-Freescale-Cup-kit/m-p/274232#M178 danielhadad 2013-08-26T03:12:55Z