topic Re: PN7150 device tree in NFC

PN7150 device tree

sivasu4098 — Sat, 06 Jul 2019 15:25:49 GMT

I have PN7150 NC controller on custom apq8909 board. I am adding the hardware configuration in the device tree. But my device is not registered in i2c bus and device noe /dev/pn544 is also not created. The following iss the device tree coniguration for PN7150. Is the configuration is either right or wrong. Please help me to solve the probem

nfc: pn544@28 {
	status = "okay";
	compatible = "nxp,pn544";
	reg = <0x28>;
	nxp,gpio_sda = <&msm_gpio 111 0x00>;
	nxp,gpio_scl = <&msm_gpio 112 0x00>;
	nxp,gpio_ven = <&msm_gpio 53 0x00>;
	nxp,gpio_mode = <&msm_gpio 27 0x00>;
	nxp,gpio_irq = <&msm_gpio 98 0x00>;
	qcom,clk-src = "BBCLK2";
	interrupt-parent = <&msm_gpio>;
	interrupts = <21 0x2>;
	interrupt-names = "nfc_irq";
	pinctrl-names = "default","suspend";
	pinctrl-0 = <&nfc_int_active &nfc_reset_active &nfc_mode_active>;
	pinctrl-1 = <&nfc_int_suspend &nfc_reset_suspend &nfc_mode_suspend>;
	nxp,i2c-pull-up = <1>;
	clocks = <&clock_rpm clk_bb_clk2_pin>;
	clock-names = "ref_clk";
	};

Thanks and Regards,

Sivasubramaniyan

Re: PN7150 device tree

weidong_sun — Mon, 08 Jul 2019 08:04:14 GMT

Hi,

The document is on how to port PN7150 to linux OS.

https://www.nxp.com/docs/en/application-note/AN11697.pdf

and device tree has been given in the application note.

Refer to the application to port your PN7150 to embeded linux, please!

Have a nice day!

BR,

Weidong

Re: PN7150 device tree

sivasu4098 — Tue, 09 Jul 2019 11:05:27 GMT

Thank you very much. Successfully device node is created

Thanks and Regards,

Sivasubramaniyan

Re: PN7150 device tree

engineer_bsp01 — Thu, 05 Sep 2019 05:54:26 GMT

sivasu4098@gmail.com Please let me known the changes that you have made in device tree..since I'm also dealing with the same issue.

Re: PN7150 device tree

sivasu4098 — Wed, 11 Sep 2019 04:18:47 GMT

nfc: pn544@28 {
                status="okay";
                compatible = "nxp,pn544";
                reg = <0x28>;
                pinctrl-names = "nfc_active","nfc_suspend";
                pinctrl-0 = <&nfc_int_active &nfc_disable_active>;
                pinctrl-1 = <&nfc_int_suspend &nfc_disable_suspend>;
                interrupt-parent = <&msm_gpio>;
                interrupts = <98 0x2>;
                enable-gpios = <&msm_gpio 53 0x1>;
                interrupt-gpios = <&msm_gpio 98 0x1>;

};

Kindly use this device tree structure engineer.bsp01@vstmobility.com‌

match the interuppt and enable pin according to your configuration

Regards,

Sivasubramaniyan P

Re: PN7150 device tree

engineer_bsp01 — Mon, 30 Sep 2019 11:43:40 GMT

Hi sivasu4098@gmail.com,

Thank u for your valuable reply. but not even detecting PN7150 as shown below.

msm8909:/ # /data/NfcFactoryTestApp

----------------------------
NFC Factory Test Application
----------------------------
Cannot connect to PN71xx NFC controller
255|msm8909:/ #

I followed this application note as it is https://www.nxp.com/docs/en/application-note/AN11690.pdf

Re: PN7150 device tree

sivasu4098 — Tue, 01 Oct 2019 06:08:21 GMT

Hi RICHU,

Please install the nxp nfc driver through insmod command and check it once again.

Regards,

Sivasubramaniyan P

Re: PN7150 device tree

engineer_bsp01 — Tue, 01 Oct 2019 06:28:20 GMT

installed pn5xx_i2c.ko in system/lib/modules using insmod command.

But nothing happens.