NFCのトピックRe: PN7642 jlink error

PN7642 jlink error

asknxp — Wed, 08 May 2024 07:52:17 GMT

Hi there,

I have used the same PN7642 development kits(https://www.nxp.com/products/rfid-nfc/nfc-hf/nfc-readers/development-kit-for-pn7642-secure-compact-nfc-controller-with-programmable-memory-and-crypto-acceleration:OM27642) and Segger J-link utra+(https://www.segger.com/products/debug-probes/j-link/models/j-link-ultra-plus/)

for a while.

It works pretty well until two days ago.

The detail of the error message is the following. I am wondering if my dev board is bad or something like that.

Any idea what happened and how to fix it?

Thank you very much

--Kenny

ERROR: Could not connect to target.
SEGGER J-Link GDB Server V7.94b Command Line Version
JLinkARM.dll V7.94b (DLL compiled Dec 13 2023 16:59:37)
Command line: -SettingsFile "/source/nfc_pn7642/application/Debug/nfc_pn7642 JLink Debug SettingsFile.jlink" -nosilent -swoport 2337 -select USB=505001876 -jlinkscriptfile /Documents/MCUXpressoIDE_11.9.0_2144/workspace/.mcuxpressoide_packages_support/PN7642_support/Script/pnev7642fama.jlinkscript -telnetport 2338 -singlerun -endian little -noir -speed 4000 -port 2339 -vd -device PN7642 -if SWD -halt -reportuseraction
-----GDB Server start settings-----
GDBInit file: none
GDB Server Listening port: 2339
SWO raw output listening port: 2337
Terminal I/O port: 2338
Accept remote connection: yes
Generate logfile: off
Verify download: on
Init regs on start: off
Silent mode: off
Single run mode: on
Target connection timeout: 0 ms
------J-Link related settings------
J-Link Host interface: USB
J-Link script: /Documents/MCUXpressoIDE_11.9.0_2144/workspace/.mcuxpressoide_packages_support/PN7642_support/Script/pnev7642fama.jlinkscript
J-Link settings file: "/source/nfc_pn7642/application/Debug/nfc_pn7642 JLink Debug SettingsFile.jlink"
------Target related settings------
Target device: PN7642
Target device parameters: none
Target interface: SWD
Target interface speed: 4000kHz
Target endian: little
Connecting to J-Link...
J-Link is connected.
Device "PN7642" selected.
Firmware: J-Link Ultra V5 compiled Dec 13 2023 14:34:48
Hardware: V5.00
S/N: 505001876
Feature(s): RDI, FlashBP, FlashDL, JFlash, GDB
Checking target voltage...
Target voltage: 3.32 V
Listening on TCP/IP port 2339
Connecting to target...
Found SW-DP with ID 0x6BA02477
DPIDR: 0x6BA02477
CoreSight SoC-400 or earlier
Scanning AP map to find all available APs
AP[1]: Stopped AP scan as end of AP map seems to be reached
AP[0]: AHB-AP (IDR: 0x84770001)
Iterating through AP map to find AHB-AP to use
AP[0]: Skipped. Could not read CPUID register
Attach to CPU failed. Executing connect under reset.
DPIDR: 0x6BA02477
CoreSight SoC-400 or earlier
Scanning AP map to find all available APs
AP[1]: Stopped AP scan as end of AP map seems to be reached
AP[0]: AHB-AP (IDR: 0x84770001)
Iterating through AP map to find AHB-AP to use
AP[0]: Skipped. Could not read CPUID register
Could not find core in Coresight setup
Found SW-DP with ID 0x6BA02477
DPIDR: 0x6BA02477
CoreSight SoC-400 or earlier
Scanning AP map to find all available APs
AP[1]: Stopped AP scan as end of AP map seems to be reached
AP[0]: AHB-AP (IDR: 0x84770001)
Iterating through AP map to find AHB-AP to use
AP[0]: Skipped. Could not read CPUID register
Attach to CPU failed. Executing connect under reset.
DPIDR: 0x6BA02477
CoreSight SoC-400 or earlier
Scanning AP map to find all available APs
AP[1]: Stopped AP scan as end of AP map seems to be reached
AP[0]: AHB-AP (IDR: 0x84770001)
Iterating through AP map to find AHB-AP to use
AP[0]: Skipped. Could not read CPUID register
Could not find core in Coresight setup
ERROR: Could not connect to target.

Re: PN7642 jlink error

KaiLi — Wed, 08 May 2024 10:05:59 GMT

Hello @asknxp

What is your FW version? Or can you enter Mass-storage mode and update the firmware to the latest version (FW02.02)and try again.

kelly

Re: PN7642 jlink error

asknxp — Wed, 08 May 2024 10:34:05 GMT

Hi Kelly,

I believe I am using FW02.02. OK. I will try to update the firmware again. Do you have a quick reference for using Mass-storge mode to update the firmware?

Thanks.

--Kenny

Re: PN7642 jlink error

asknxp — Wed, 08 May 2024 13:16:02 GMT

OK. I think I found the documentation for Mass-storage mode to update the firmware.

https://www.nxp.com/docs/en/application-note/AN13134.pdf page 54.

However, I have no idea which file I should put.

[kenny@MBP PN7642_FW_v02.02]$ ls -l
total 1840
-rw-r--r--@ 1 kenny staff 207995 Oct 10 2023 NXP_SLDA.pdf
-rw-r--r--@ 1 kenny staff 115 Oct 6 2023 PN7642_Default_AESChipKey.txt
-rw-r--r--@ 1 kenny staff 5702 Oct 6 2023 PN7642_Default_App_RSAKey.pem
-rw-r--r--@ 1 kenny staff 55036 Dec 15 2022 PN7642_SecureFW_SCR.pdf
-rw-r--r--@ 1 kenny staff 40114 Oct 9 2023 PN7642_v02.F2.esfwu
-rw-r--r--@ 1 kenny staff 1770 Oct 10 2023 ReadMe.txt
-rw-r--r--@ 1 kenny staff 306336 Oct 9 2023 phDnldNfc_UpdateSeq_v02.02.c
-rw-r--r--@ 1 kenny staff 256876 Oct 9 2023 phDnldNfc_UpdateSeq_v02.F2.c
-rw-r--r--@ 1 kenny staff 47842 Oct 9 2023 pn7642_v02.02.esfwu
-rw-r--r--@ 1 kenny staff 232 Oct 6 2023 version.txt

I assume that should be a bin file format.

Here is the screenshot when board operates in Mass-storage mode.

--Kenny

Re: PN7642 jlink error

asknxp — Wed, 08 May 2024 13:36:40 GMT

OK. Here is what I did to solve the issue.

- After board operates in Mass-Storage mode

- Delete the CRP_00.BIN(180KB)

- Then copy one of the .bin application fw to the drive.

- Then my J-link works again.

Thanks Kelly for the hints.

--Kenny