MPC5xxxのトピックRe: MCAL drivers

MCAL drivers

DariushTsh — Sat, 25 Dec 2021 08:29:05 GMT

I have MCAL drivers for MPC560 and MPC563 microcontrollers (AUTOSAR 3.0 and 4.0). Can we use them to write MCAL drivers for SPC560 and SPC563 microcontrollers?

Re: MCAL drivers

namnguyenviet — Thu, 30 Dec 2021 02:00:40 GMT

Hello @DariushTsh,

If you're asking about the SPC560/SPC563 microcontrollers which are listed out here: https://www.nxp.com/products/processors-and-microcontrollers/power-architecture/mpc5xxx-microcontrollers/ultra-reliable-mpc56xx-mcus/ultra-reliable-mpc56xb-mcu-for-automotive-and-industrial-general-purpose:MPC560xB?tab=Buy_Parametric_Tab#/ and here: https://www.nxp.com/products/processors-and-microcontrollers/power-architecture/mpc5xxx-microcontrollers/ultra-reliable-mpc56xx-mcus/ultra-reliable-mpc563xm-for-automotive-industrial-engine-management:MPC563xM?tab=Buy_Parametric_Tab#/
Then the answer is yes, you can use the MCAL drivers for MPC560/MPC563 in those products.

Best Regards,

Nam

Re: MCAL drivers

DariushTsh — Thu, 30 Dec 2021 19:14:53 GMT

Please help me to configure and use MCAL drivers with EB tresos Studio.

Re: MCAL drivers

namnguyenviet — Fri, 31 Dec 2021 03:21:21 GMT

Hello,

You can refer to this video: https://www.nxp.com/video/introduction-to-nxp-autosar-mcal-software:AUTOSAR-OnDemand-Training-Video

Best Regards,

Nam

Re: MCAL drivers

DariushTsh — Fri, 31 Dec 2021 09:50:06 GMT

What MCAL drivers of NXP microcontrollers can be used for SPC563M64L5 microcontroller (of ST)?

Re: MCAL drivers

namnguyenviet — Fri, 31 Dec 2021 09:52:57 GMT

Unfortunately, there isn't any NXP MCAL drivers can be used for an ST microcontroller.

Re: MCAL drivers

DariushTsh — Fri, 31 Dec 2021 10:05:44 GMT

Because SPC and MPC have a common architecture, can't use each other's MCAL drivers?

But you said in this post, this is possible.

Re: MCAL drivers

namnguyenviet — Fri, 31 Dec 2021 10:14:16 GMT

Hello,

I'm afraid you have a misunderstood. What I meant is the SPC microcontroller from NXP, not ST. Please carefully read the whole comment and check the link that I have provided, which listed out only NXP products, and not any product from ST.

Best Regards,

Nam

Re: MCAL drivers

DariushTsh — Fri, 31 Dec 2021 10:31:55 GMT

Oh ... I'm a little confused. Can I email you or privately? Because I have many questions.

Re: MCAL drivers

namnguyenviet — Fri, 31 Dec 2021 10:38:07 GMT

Hello,

Please create a ticket in here: https://support.nxp.com/s/ and our experts will be assigned to support you.

Best Regards,

Nam

Re: MCAL drivers

DariushTsh — Fri, 31 Dec 2021 10:42:13 GMT

Thanks ...

Re: MCAL drivers

DariushTsh — Fri, 31 Dec 2021 14:53:06 GMT

I'm confused.
Did I get it right ??? MPC microcontrollers can (of NXP) be used instead of SPC (of ST), but MCAL drivers of MPC microcontrollers (of NXP) can not be used for SPC microcontrollers (of ST) . Is it correct???

Re: MCAL drivers

namnguyenviet — Fri, 31 Dec 2021 15:02:22 GMT

Hello,

If you want to integrate the NXP MCAL driver into a ST microcontroller, then you need to use with your own risks. Although the hardware might be equivalent between these two microcontrollers, it remains the fact that the NXP MCAL is only verified with NXP microcontrollers, and we can't guarantee that there wouldn't be any issue when integrating a NXP MCAL software into a ST microcontroller, or whichever another company's microcontroller.

Best Regards,

Nam

Re: MCAL drivers

DariushTsh — Fri, 31 Dec 2021 16:08:00 GMT

I have a general question.

Can MCAL drivers be prepared and written by software engineers and programmers at all or must they be purchased ???

Please explain about MCAL drivers and their standard

Re: MCAL drivers

namnguyenviet — Tue, 04 Jan 2022 06:37:24 GMT

Hello,

Definitely you can develop for your own the AUTOSAR MCAL drivers in a NXP microcontroller. It's not mandatory to purchase the NXP AUTOSAR MCAL.

You can figure out the portfolio of our AUTOSAR MCAL here: https://www.nxp.com/design/automotive-software-and-tools/autosar:AUTOSAR-HOME

Best Regards,

Nam

Re: MCAL drivers

DariushTsh — Wed, 05 Jan 2022 09:19:35 GMT

Thanks...