MPC5xxxのトピックRe: CW11.1 for MPC56X Problem1

CW11.1 for MPC56X Problem1

NXP_Hongyu — Wed, 22 Sep 2021 06:41:31 GMT

Capture.PNGwhen i installed the CW11.1, i can't create a new project for MPC56X, because i can't find relevant device

Re: CW11.1 for MPC56X Problem1

lukaszadrapa — Wed, 22 Sep 2021 10:51:27 GMT

Hi,

it was necessary to select "Qorivva" (this was a nickname for MPC5xxx devices in the past) during the installation:

lukaszadrapa_0-1632307753339.png

To add support to existing installation, open Help -> Install New Software

and select:

lukaszadrapa_1-1632307858493.png

Regards,

Lukas

Re: CW11.1 for MPC56X Problem1

NXP_Leo — Thu, 23 Sep 2021 03:22:59 GMT

I operate according to your instructions, i meet a new issue below:

Capture.PNG

I disable the 1.0.3 version of buildtools, then it can continue again, but i don't know whether this will influence my developpment.

Re: CW11.1 for MPC56X Problem1

lukaszadrapa — Thu, 23 Sep 2021 05:26:03 GMT

That should be ok, it's just older version which is not needed.

Regards,

Lukas

Re: CW11.1 for MPC56X Problem1

NXP_Leo — Thu, 23 Sep 2021 05:57:51 GMT

Thanks for your support!

Re: CW11.1 for MPC56X Problem1

NXP_Leo — Fri, 24 Sep 2021 02:30:43 GMT

Capture.PNG

MCU above is what i use, but i don't know which family i should select from item below:

Capture1.PNG

Re: CW11.1 for MPC56X Problem1

lukaszadrapa — Fri, 24 Sep 2021 06:04:28 GMT

Hi,

if you really have SPC5604P34/SPC560P40, you are talking to wrong company. These are parts from ST. Please contact www.st.com

Regards,

Lukas

Re: CW11.1 for MPC56X Problem1

JOE_1209 — Wed, 22 Dec 2021 08:45:41 GMT

Hi Lukas,

I am also using the chip MPC5602P and I have followed the instruction to update the Qorivva Support & MCU v11.1 Update for Qorivva. However, when I created a new project for MPC5602P, the component inspector is blank. I assume there is no SDK S32PA support for MPC5602P? I also tried S32 design studio power architecture, the component inspector is blank as well

S32 Design Studio問題.PNG

Regards,

Joe

Re: CW11.1 for MPC56X Problem1

lukaszadrapa — Wed, 22 Dec 2021 12:39:53 GMT

Hi,

yes, that's correct. There's no SDK for MPC56xx family of devices. We provided Autosar MCAL only:

https://www.nxp.com/design/automotive-software-and-tools/autosar:AUTOSAR-HOME

Regards,

Lukas

Re: CW11.1 for MPC56X Problem1

JOE_1209 — Thu, 23 Dec 2021 05:30:59 GMT

Hi Lukas,

Thank you for the reply. I installed the files

1. STUDIO_14.0.0_2013-02-26

2. MPC560XP_MCAL4.0_RTM_1.0.0_signed

3. MPC560XP_MCAL4.0_RTM_HF1_1.0.0_signed

For the MCAL4.0 RTM, I installed them under the path of "C:\EB\tresos\plugins"

file directory.PNG

When I clicked file -> import -> Existing Project into Workspace on Tresos studio, I selected "MPC560XP_MCAL4.0_RTM_1.0.0_Integration_Application" as root directory. (which then be copied into workspace). Then I clicked SampleApplication (PA, XPC560XP), it prompted a warning showing T2D11M10I0R0 is not installed. Where should I move all the files with T2D11M10I0R0 ending? So the Tresos Studio can load the configuration.

EBtresos.PNG

My intent here is to only configure the low level driver and pin configuration. no need for OS.

Best Regards,

Joe

Re: CW11.1 for MPC56X Problem1

lukaszadrapa — Mon, 03 Jan 2022 06:07:50 GMT

Hi Joe,

I'm sorry for delayed response caused by Christmas holidays. This is for another team, so if it is still not resolved, please create new ticket here and it will be assigned to them:

https://support.nxp.com/

Thanks,

Lukas

Re: CW11.1 for MPC56X Problem1

JOE_1209 — Mon, 03 Jan 2022 07:42:50 GMT

Hi Lukas,

Happy 2022, I created a new post and Nam is helping me with the issue

Thanks,

Joe