topic Re: ERROR: InitTarget(): PCode returned with error code -1 in MCUXpresso IDE

ERROR: InitTarget(): PCode returned with error code -1

chiao-weitsai — Thu, 20 Jul 2017 02:51:58 GMT

Hi All:

I try to load example project to FRDM-KW41Z, But it always show "ERROR: InitTarget(): PCode returned with error code -1".

I also try removing Anti-virus and disabling firmwall. But i also get same issue.

Please help to check log and give me some suggestion. thanks.

Board:FRDM-KW41Z

IDE:MCUXpresso IDE v10.0.2 [Build 411] [2017-07-11]

Project:frdmkw41z_demo_apps_hello_world

==============LOG===========================

Could not connect to target.
SEGGER J-Link GDB Server V6.16b Command Line Version
JLinkARM.dll V6.16b (DLL compiled Jun 9 2017 18:03:30)
-----GDB Server start settings-----
GDBInit file:                  none
GDB Server Listening port:     2331
SWO raw output listening port: 2332
Terminal I/O port:             2333
Accept remote connection:      localhost only
Generate logfile:              off
Verify download:               on
Init regs on start:            off
Silent mode:                   off
Single run mode:               on
Target connection timeout:     0 ms
------J-Link related settings------
J-Link Host interface:         USB
J-Link script:                 none
J-Link settings file:          none
------Target related settings------
Target device:                 MKW41Z512xxx4
Target interface:              SWD
Target interface speed:        auto
Target endian:                 little
Connecting to J-Link...
$$UserActionStart$$: Terms of use
$$UserActionEnd$$: Terms of use
J-Link is connected.
Device "MKW41Z512XXX4" selected.
Firmware: J-Link OpenSDA 2 compiled May 6 2016 11:04:17
Hardware: V1.00
S/N: 621000000
Checking target voltage...
Target voltage: 3.30 V
Listening on TCP/IP port 2331
Connecting to target...Executing InitTarget()
Connect Under Reset
Connect Under Reset
Executing InitTarget()
Connect Under Reset
Connect Under Reset
ERROR: InitTarget(): PCode returned with error code -1
Executing InitTarget()
Connect Under Reset
Connect Under Reset
Executing InitTarget()
Connect Under Reset
Connect Under Reset
ERROR: InitTarget(): PCode returned with error code -1
ERROR: Could not connect to target.
Target connection failed. GDBServer will be closed...Restoring target state and closing J-Link connection...
Shutting down...
Could not connect to target.
Please check power, connection and settings.

Re: ERROR: InitTarget(): PCode returned with error code -1

ZhangJennie — Tue, 08 Aug 2017 03:52:57 GMT

You met board connection problem.

to confirm if this problem is on firmware side,I suggest you update your board firmware then test again.

OpenSDA Serial and Debug Adapter|NXP

I suggest you try DAPLink rev0241

Can this firmware fix the connection problem?

Have a great day,
Jennie Zhang

-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------

Re: ERROR: InitTarget(): PCode returned with error code -1

nxf42424 — Tue, 12 Mar 2019 11:30:40 GMT

Hi I have tried on the TWR-K65F120M platform, but it will produce this result！

I downloaded this.

Re: ERROR: InitTarget(): PCode returned with error code -1

ZhangJennie — Wed, 13 Mar 2019 03:17:52 GMT

Hi Ding,

This thread is of two years ago. We don't maintain it now.

I suggest you create a new thread for your issue.

We will help.

Thanks for your understanding.

Have a nice day,

Jennie Zhang