https://community.nxp.com/t5/Model-Based-Design-Toolbox-MBDT/Data-Measurement-amp-Parameter-Calibration-over-CAN-using-NXP/m-p/1877858#M9152 <P>Dear Team,&nbsp;</P><P>Was able to successfully flash &amp; run code on to S32K144 MCU based ECU board directly out of Matlab-Simulink - NXP MBDT over Seggar Jlink. The code has the Freemaster Config Block over CAN2 at 1M Baud - Refer Image #1&nbsp;&nbsp;<span class="lia-inline-image-display-wrapper lia-image-align-inline" image-alt="Freemaster Block Config.png" style="width: 999px;"><img src="https://community.nxp.com/t5/image/serverpage/image-id/281661i634DE5ABABAD4682/image-size/large?v=v2&amp;px=999" role="button" title="Freemaster Block Config.png" alt="Freemaster Block Config.png" /></span><span class="lia-inline-image-display-wrapper lia-image-align-inline" image-alt="image.png" style="width: 669px;"><img src="https://community.nxp.com/t5/image/serverpage/image-id/281662iD5913D79F0B4BFAF/image-size/large?v=v2&amp;px=999" role="button" title="image.png" alt="image.png" /></span><span class="lia-inline-image-display-wrapper lia-image-align-inline" image-alt="image.png" style="width: 484px;"><img src="https://community.nxp.com/t5/image/serverpage/image-id/281663i149DDD362F4552C9/image-size/large?v=v2&amp;px=999" role="button" title="image.png" alt="image.png" /></span></P><P><BR />Upon Opening Freemaster to enable the connection over CAN2&nbsp;@1000K Baud , the tool detects my connected CAN2USB HW but the connection is not established.</P><OL><LI>Is it because it checking for drivers in the location : C:\Windows\SYSTEM32\canlib32.dll where it cannot be found as this is greyed out for user to enter a different location. The latest Kavaser Driver for Windows is&nbsp;V5.44.630 but not sure it corresponds to the number 8.40.102.0 mentioned on the GUI&nbsp;</LI><LI>Is it because the default command message ID &amp; Response Message ID are the same at&nbsp;0x7aa and need to be some other - could not find any such info in the Simulink config block to set&nbsp;&nbsp;</LI></OL><P>Thanks a lot for the superb tool chain once again to your team and congratulations!&nbsp;</P> Thu, 30 May 2024 04:43:46 GMT Vasappanavara 2024-05-30T04:43:46Z https://community.nxp.com/t5/Model-Based-Design-Toolbox-MBDT/Data-Measurement-amp-Parameter-Calibration-over-CAN-using-NXP/m-p/1877858#M9152 <P>Dear Team,&nbsp;</P><P>Was able to successfully flash &amp; run code on to S32K144 MCU based ECU board directly out of Matlab-Simulink - NXP MBDT over Seggar Jlink. The code has the Freemaster Config Block over CAN2 at 1M Baud - Refer Image #1&nbsp;&nbsp;<span class="lia-inline-image-display-wrapper lia-image-align-inline" image-alt="Freemaster Block Config.png" style="width: 999px;"><img src="https://community.nxp.com/t5/image/serverpage/image-id/281661i634DE5ABABAD4682/image-size/large?v=v2&amp;px=999" role="button" title="Freemaster Block Config.png" alt="Freemaster Block Config.png" /></span><span class="lia-inline-image-display-wrapper lia-image-align-inline" image-alt="image.png" style="width: 669px;"><img src="https://community.nxp.com/t5/image/serverpage/image-id/281662iD5913D79F0B4BFAF/image-size/large?v=v2&amp;px=999" role="button" title="image.png" alt="image.png" /></span><span class="lia-inline-image-display-wrapper lia-image-align-inline" image-alt="image.png" style="width: 484px;"><img src="https://community.nxp.com/t5/image/serverpage/image-id/281663i149DDD362F4552C9/image-size/large?v=v2&amp;px=999" role="button" title="image.png" alt="image.png" /></span></P><P><BR />Upon Opening Freemaster to enable the connection over CAN2&nbsp;@1000K Baud , the tool detects my connected CAN2USB HW but the connection is not established.</P><OL><LI>Is it because it checking for drivers in the location : C:\Windows\SYSTEM32\canlib32.dll where it cannot be found as this is greyed out for user to enter a different location. The latest Kavaser Driver for Windows is&nbsp;V5.44.630 but not sure it corresponds to the number 8.40.102.0 mentioned on the GUI&nbsp;</LI><LI>Is it because the default command message ID &amp; Response Message ID are the same at&nbsp;0x7aa and need to be some other - could not find any such info in the Simulink config block to set&nbsp;&nbsp;</LI></OL><P>Thanks a lot for the superb tool chain once again to your team and congratulations!&nbsp;</P> Thu, 30 May 2024 04:43:46 GMT https://community.nxp.com/t5/Model-Based-Design-Toolbox-MBDT/Data-Measurement-amp-Parameter-Calibration-over-CAN-using-NXP/m-p/1877858#M9152 Vasappanavara 2024-05-30T04:43:46Z