Model-Based Design Toolbox (MBDT)のトピックRe: Conflicting identifiers issue after installation of MBDT for for S32K14 and MC Development Toolbox for Kinetis

Conflicting identifiers issue after installation of MBDT for for S32K14 and MC Development Toolbox for Kinetis

m_benderradji — Fri, 25 Jan 2019 14:07:08 GMT

Hello,

I'have installed:

Model-Based Design Toolbox for S32K14x Automotive MCU 2018.R1

and

MC Development Toolbox for Kinetis

In matlab command window, i have the following Warning. Could you please tel me how i can resolve this issue

Warning: Incorrect internal Simulink identifiers were detected. The following blocks have
conflicting identifiers:
'mcd_kv_ec_toolbox/KV5xF/Math and Motor Control Library'
'mcd_kv_ec_toolbox/KV3xF/Math and Motor Control Library'.
The Simulink identifier of 'mcd_kv_ec_toolbox/KV5xF/Math and Motor Control Library' was
changed from '65' to '91'. Backup the original model, and then save and reopen the current
model.
> In LibraryBrowser.internal.generateRepository
In LibraryBrowser.internal.generateRepository
In LibraryBrowser.internal.generateRepository
In LibraryBrowser.internal.generateRepository
In LibraryBrowser.internal.findLibraryInfo
In LibraryBrowser.internal.findLibraryInfo
In LibraryBrowser.internal.findLibraryInfo
Warning: Incorrect internal Simulink identifiers were detected. The following blocks have
conflicting identifiers:
'mcd_kv_ec_toolbox/KV5xF/Math and Motor Control Library'
'mcd_kv_ec_toolbox/KV3xF/Math and Motor Control Library'.
The Simulink identifier of 'mcd_kv_ec_toolbox/KV5xF/Math and Motor Control Library' was
changed from '65' to '91'. Backup the original model, and then save and reopen the current
model.
> In LibraryBrowser.internal.generateRepository
In LibraryBrowser.internal.generateRepository
In LibraryBrowser.internal.generateRepository
In LibraryBrowser.internal.generateRepository
In LibraryBrowser.internal.findLibraryInfo
In LibraryBrowser.internal.findLibraryInfo
In LibraryBrowser.internal.findLibraryInfo

regards

Re: Conflicting identifiers issue after installation of MBDT for for S32K14 and MC Development Toolbox for Kinetis

m_benderradji — Tue, 29 Jan 2019 14:07:00 GMT

Hello,

Any feedback please ? thanks in advance

Re: Conflicting identifiers issue after installation of MBDT for for S32K14 and MC Development Toolbox for Kinetis

constantinrazva — Tue, 29 Jan 2019 14:34:53 GMT

Hello m.benderradji@outlook.fr‌,

Can you try and reset the MATLAB path? For that you should go to MATLAB Home tab -> Set Path -> Click on Default -> Then click on Save.

and then run the mbd_s32k_path script so you install the path for the toolbox over a fresh, default MATLAB path.

Note: you will lose other paths other than the default + S32K toolbox paths by doing this. Consider saving the current contents of your MATLAB path (you can get it by typing matlabpath in the MATLAB terminal for instance).

Note: this file is located in {INSTALL_ROOT}/src.

Kind regards,

Razvan.

Re: Conflicting identifiers issue after installation of MBDT for for S32K14 and MC Development Toolbox for Kinetis

m_benderradji — Wed, 30 Jan 2019 14:07:08 GMT

Hello,

I have done the requested step but the issue still exsist.

First, i have setted the default path and next applied teh mbd_s32k_path to add MBDT for S32

I had:

MBD Toolbox path prepended.
Successful.

Secondly, i have applied mcd_kv_path to add MC toolbox for kentis

I had:

Treating 'C:\MCToolbox\mctbx_Kinetis' as MCD Toolbox installation root.
MCD Toolbox path prepended.
Successful.

by typin ver I had:

Model-Based Design Toolbox for S32K1xx Series Version 2018.R1 (R2016b-R2018a)
Motor Control Development Toolbox for Kinetis Version 1.4 (R2014a-R2015b)

When i refrech the simulink librery i had the issue:

Re: Conflicting identifiers issue after installation of MBDT for for S32K14 and MC Development Toolbox for Kinetis

m_benderradji — Tue, 05 Feb 2019 10:58:48 GMT

Hello NXP tram,

Any feedback please ?

Thanks in avance for your support