Model-Based Design Toolbox (MBDT)中的主题 Re: Issue with gpio_s32k144 example

Issue with gpio_s32k144 example

m_benderradji — Sun, 06 Jan 2019 15:19:45 GMT

Hello,

I'am using

Model-Based Design Toolbox for S32K14x Automotive MCU 2018.R1

I try to build the gpio_s32k144 example in order to use it with S32K144EVB. I have the following issue:

### Build procedure for model: 'gpio_s32k144' aborted due to an error.
For S-function 'gpio_s32k14_output', the number of defined parameters, 4, does not match the number of parameters on the dialog of 'gpio_s32k144/Digital_Output', 0. These two values must be identical.
Component:Simulink | Category:Block diagram error
For S-function 'gpio_s32k14_output', the number of defined parameters, 4, does not match the number of parameters on the dialog of 'gpio_s32k144/GREEN_LED', 0. These two values must be identical.
Component:Simulink | Category:Block diagram error
For S-function 'gpio_s32k14_input', the number of defined parameters, 6, does not match the number of parameters on the dialog of 'gpio_s32k144/SW2', 0. These two values must be identical.
Component:Simulink | Category:Block diagram error

Could you please tel me what i need to do ? thanks in advance

Regards

Re: Issue with gpio_s32k144 example

mariuslucianand — Mon, 07 Jan 2019 09:28:48 GMT

Hello m.benderradji@outlook.fr‌,

Have you installed the 2018.R1 over the last MBDT version?

Please reset the Matlab "Set Path" to "Default" like in the attached image and then perform a clean install of the MBDT 2018.R1.

Best regards,

Marius

Re: Issue with gpio_s32k144 example

m_benderradji — Mon, 07 Jan 2019 18:39:09 GMT

Hello and thanks for your support.

I have already installed the 2018.R1. I have this issue with this last version.

What do you mean by "perform a clean install of the MBDT 2018.R1" after "set path"

Thank in advance for your replay

regards

Re: Issue with gpio_s32k144 example

mariuslucianand — Tue, 08 Jan 2019 09:37:28 GMT

Hello m.benderradji@outlook.fr‌,

I assumed that you used the old toolbox version before and the files from the last toolbox version were still in the Matlab's path. So with a clean install I want to be sure that the only files related with the MBDT toolbox are the ones from the current toolbox.

Now, you set the paths to default, go to the Addons folder which typically is C:\Users\[...]\Documents\MATLAB\Add-Ons and in the MBDT toolbox please run the "mbd_s32k_path.m" script.

Now, if you type the command "ver" in the Matlab Command Window, you need to be sure that you have only one toolbox related with S32K. For example I only have this "Model-Based Design Toolbox for S32K1xx Series Version 2018.R1 (R2016b-R2018a)".

Hope this helps,

Marius

Re: Issue with gpio_s32k144 example

m_benderradji — Tue, 08 Jan 2019 10:25:11 GMT

Hello Marius,

Thank you for your support.

I did not install the old version of MBDT. would you tell me if the issue comes from the installation of the "Motor Control Toolbox supporting S32K"

I'have installed this tool box with the pervious one (MBDT 2018 R1).

Best regards

Re: Issue with gpio_s32k144 example

mariuslucianand — Tue, 08 Jan 2019 12:13:14 GMT

Hello m.benderradji@outlook.fr‌,

Please uninstall the "Motor Control Toolbox supporting S32K" and use only "Model-Based Design Toolbox for S32K1xx Series". All the features from that toolbox are embedded in 2018.R1. For a clean install you can follow my previous responses.

Best regards,

Marius

Re: Issue with gpio_s32k144 example

m_benderradji — Tue, 08 Jan 2019 13:04:23 GMT

Thanks Marius

IIs it possible to use Model BaseD Design toolbox without Embedded coder from mathworks ? Is it possible to use only with Matlab coder and Simulink coder ?

Best regards

Re: Issue with gpio_s32k144 example

mariuslucianand — Tue, 08 Jan 2019 13:24:11 GMT

Hello m.benderradji@outlook.fr‌,

It is not possible to use the MBDT toolbox without Embedded Coder.

Marius

Re: Issue with gpio_s32k144 example

m_benderradji — Thu, 10 Jan 2019 08:58:09 GMT

Hello Marious,

Could you please tell me where i can find the steps to follow in order to setup the compilerr for MBDT 2018.R1

I want to use the requested compiler instead of the default one "GCC 6.3 compiler" i think.

Thanks in advance for your support

Re: Issue with gpio_s32k144 example

mariuslucianand — Thu, 10 Jan 2019 09:39:10 GMT

Hello m.benderradji@outlook.fr‌,

To use another GCC compiler it is enough to declare an Environment Variable named "GCC_S32K_TOOL" to the location where the GCC complier is installed and restart Matlab after that. If no variable is declared the MBDT uses the default compiler located at "C:\Users\[...]\Documents\MATLAB\Add-Ons\Toolboxes\NXP_MBDToolbox_S32K1xx\code\tools\gcc-6.3-arm32-eabi"

Best regards,

Marius

Re: Issue with gpio_s32k144 example

m_benderradji — Fri, 11 Jan 2019 08:06:04 GMT

Hello Maruis,

Could you please tell me how to declare the environment Variable named "GCC_S32K_TOOL".

is it a command to type on matlab ?

Thanks in advance. Regards

Re: Issue with gpio_s32k144 example

mariuslucianand — Fri, 11 Jan 2019 10:59:19 GMT

Hello m.benderradji@outlook.fr‌,

For adding an environment variable in Windows you need to right click Computer -> Properties -> Advanced system Settings and in the Advanced tab you click the "Environment Variables". Then press New... and add the GCC_S32K_TOOl variable name and the compiler location. After that restart Matlab and it will use the new compiler.

Best regards,

Marius

Re: Issue with gpio_s32k144 example

m_benderradji — Sat, 12 Jan 2019 13:06:23 GMT

Thanks for your support