LPC MicrocontrollersのトピックRe: Flashing EVSE-SIG-BRD2X board

Flashing EVSE-SIG-BRD2X board

mjadan — Thu, 19 Mar 2026 08:15:40 GMT

I am working with an EVSE-SIG-BRD2X board and trying to flash EV-side software onto it. My setup consists of a Linux machine connected to an i.MX 93 EVK board, which is in turn connected to the EVSE-SIG-BRD2X. The EVSE-SIG-BRD2X is powered by the i.MX 93 EVK, so jumpers J2 and J3 are set to pins 2–3.

For debugging, I am using an MCU-Link Debug Probe connected to the SWD debug port J30, and LinkServer is installed and updated on my Linux system.

LinkServer --version

When checking for available probes, I get the following:

I am building and flashing the project using MCUXpresso IDE. The build completes successfully, but flashing fails with the following error:

Using the GUI Flash Tool

I get the same error

I click cancel

I also attempted flashing via LinkServer:

LinkServer devices | grep LPC55S36
LinkServer flash -p '#1' LPC55S36 load /home/mj/Desktop/EV/NXP_EasyEVSE/workplace/evsigbrd_sw/Debug/evsigbrd_sw.axf

Since SWD did not work, I switched to ISP programming. I opened jumper J29 to enable ISP mode and connected a UART TTL adapter to J46 (pins 2, 3, and 4). Then I ran:

Downloads/blhost_2.6.7/bin/linux/amd64/blhost -p /dev/ttyUSB0,115200 -- get-property 1

Downloads/blhost_2.6.7/bin/linux/amd64/blhost -p /dev/ttyUSB0,115200 -- flash-erase-all

Unfortunately, it is still not working. I would appreciate any suggestions on how to resolve this issue.

Thanks

Re: Flashing EVSE-SIG-BRD2X board

Zhiming_Liu — Mon, 23 Mar 2026 01:18:16 GMT

Hi @mjadan

Please measure and monitor the voltage on the download pin.

Best Regards,
Zhiming

Re: Flashing EVSE-SIG-BRD2X board

mjadan — Mon, 23 Mar 2026 18:25:12 GMT

Hello Zhiming,

Thank you for your response. I measured the voltage on all pins of J46 (Aux UART) with J29 open:

Pin 1: 3.34 V
Pin 2: 0 V
Pin 3: 0 V
Pin 4: GND

Re: Flashing EVSE-SIG-BRD2X board

Zhiming_Liu — Tue, 31 Mar 2026 02:36:57 GMT

Hi @mjadan

It's strange that there's no active signal on TXD/RXD. Could you check the LPC55S36's power supply against the schematic to see if it's working properly?

Best Regards,
Zhiming

Re: Flashing EVSE-SIG-BRD2X board

mjadan — Tue, 31 Mar 2026 08:30:50 GMT

Hi Zhiming, thank you again for your response.

By default, pins 1 and 2 on all the jumpers you mentioned are connected. The measured voltages are:

J25: 3.3V
J26: 3.3V
J27: 3.3V
J28: 3.3V
J29: 0V

I then opened all the jumpers and recorded the following measurements:

J25 — Pin 1: 3.3V, Pin 2: 2.6V
J26 — Pin 1: 3.3V, Pin 2: 2.6V
J27 — Pin 1: 3.3V, Pin 2: 1.7V
J28 — Pin 1: 3.3V, Pin 2: 0V
J29 — Pin 1: 2.3V, Pin 2: 0V

Re: Flashing EVSE-SIG-BRD2X board

Zhiming_Liu — Tue, 07 Apr 2026 01:49:10 GMT

Hi @mjadan

You can try the following steps to see if you can flash the device using Windows. If that doesn't work, please contact the sales team to see if you can request a replacement.

https://docs.nxp.com/bundle/UG10140/page/topics/programming_evse-sig-brd_software.html

Best Regards,
Zhiming