https://community.nxp.com/t5/LPC-Microcontrollers/LPC1113-202/m-p/2190288#M58897 <P>Hi <a href="https://community.nxp.com/t5/user/viewprofilepage/user-id/255730">@SkyPilot</a>,</P> <P>The following debuggers support LPC1100</P> <P><A href="https://www.nxp.com/design/design-center/development-boards-and-designs/universal-multilink-development-interface:UMultilink" target="_blank">Universal Multilink Development Interface | NXP Semiconductors</A></P> <P><A href="https://www.nxp.com/design/design-center/development-boards-and-designs/CYCLONE-FX" target="_blank">PEmicro Cyclone FX programmer | NXP Semiconductors</A></P> <P><A href="https://www.nxp.com/design/design-center/development-boards-and-designs/U-MULTILINK-FX" target="_blank">Universal Multilink FX High-Speed Development Interface | NXP Semiconductors</A></P> <P><A href="https://www.nxp.com/design/design-center/development-boards-and-designs/CYCLONE" target="_blank">PEmicro Cyclone programmer | NXP Semiconductors</A></P> <P>You can refer to the connections on the following board, which supports the LPC1100 series:</P> <P><A href="https://www.nxp.com/design/design-center/software/development-software/mcuxpresso-software-and-tools-/lpcxpresso-boards/lpcxpresso1125-board:OM13080" target="_blank">LPCXpresso1125 Board | NXP Semiconductors</A></P> <P>Additionally, according to Section 6.2: Pin Description in the datasheet, a LOW level on pin PIO0_1 during reset triggers the ISP command handler.</P> <P>Best Regards,</P> <P>Pablo</P> Tue, 21 Oct 2025 22:46:24 GMT Pablo_Ramos 2025-10-21T22:46:24Z https://community.nxp.com/t5/LPC-Microcontrollers/LPC1113-202/m-p/2187573#M58869 <P>Hello, We are an aviation company that uses the LPC1113 /202 controller in our instruments. We needing to source a module / socket with pins so we can access so we can program the chip in ISP mode.</P><P>&nbsp;</P><P>Any help would be appreciated.</P> Thu, 16 Oct 2025 14:07:30 GMT https://community.nxp.com/t5/LPC-Microcontrollers/LPC1113-202/m-p/2187573#M58869 SkyPilot 2025-10-16T14:07:30Z https://community.nxp.com/t5/LPC-Microcontrollers/LPC1113-202/m-p/2190288#M58897 <P>Hi <a href="https://community.nxp.com/t5/user/viewprofilepage/user-id/255730">@SkyPilot</a>,</P> <P>The following debuggers support LPC1100</P> <P><A href="https://www.nxp.com/design/design-center/development-boards-and-designs/universal-multilink-development-interface:UMultilink" target="_blank">Universal Multilink Development Interface | NXP Semiconductors</A></P> <P><A href="https://www.nxp.com/design/design-center/development-boards-and-designs/CYCLONE-FX" target="_blank">PEmicro Cyclone FX programmer | NXP Semiconductors</A></P> <P><A href="https://www.nxp.com/design/design-center/development-boards-and-designs/U-MULTILINK-FX" target="_blank">Universal Multilink FX High-Speed Development Interface | NXP Semiconductors</A></P> <P><A href="https://www.nxp.com/design/design-center/development-boards-and-designs/CYCLONE" target="_blank">PEmicro Cyclone programmer | NXP Semiconductors</A></P> <P>You can refer to the connections on the following board, which supports the LPC1100 series:</P> <P><A href="https://www.nxp.com/design/design-center/software/development-software/mcuxpresso-software-and-tools-/lpcxpresso-boards/lpcxpresso1125-board:OM13080" target="_blank">LPCXpresso1125 Board | NXP Semiconductors</A></P> <P>Additionally, according to Section 6.2: Pin Description in the datasheet, a LOW level on pin PIO0_1 during reset triggers the ISP command handler.</P> <P>Best Regards,</P> <P>Pablo</P> Tue, 21 Oct 2025 22:46:24 GMT https://community.nxp.com/t5/LPC-Microcontrollers/LPC1113-202/m-p/2190288#M58897 Pablo_Ramos 2025-10-21T22:46:24Z https://community.nxp.com/t5/LPC-Microcontrollers/LPC1113-202/m-p/2190974#M58901 <P>Thank you&nbsp;<SPAN>Pablo,</SPAN></P><P>&nbsp;</P><P><SPAN>This should get me on the right track.</SPAN></P> Wed, 22 Oct 2025 19:37:57 GMT https://community.nxp.com/t5/LPC-Microcontrollers/LPC1113-202/m-p/2190974#M58901 SkyPilot 2025-10-22T19:37:57Z