LPC55S69 Ctimer2 CAP doesn't work

qingyunliu — Fri, 30 Dec 2022 10:50:07 GMT

I want use Ctimer2 cap function to calculate PWM frequency.

I find the similar introduction, eg

[1] https://community.nxp.com/t5/LPC-Microcontrollers-Knowledge/LPC845-Pulse-width-Measurement-Using-CTIMER/ta-p/1254941

[2] https://www.freesion.com/article/4997763456/ the pin is P1_9, I configure it as following code, but it can not work if I press SW3(P1_9), no Ctimer2 IRQ is trigger.

const uint32_t port1_pin9_config = (/* Pin is configured as CTIMER_INP4 */
IOCON_PIO_FUNC3 |
/* No addition pin function */
IOCON_PIO_MODE_INACT |
/* Standard mode, output slew rate control is enabled */
IOCON_PIO_SLEW_STANDARD |
/* Input function is not inverted */
IOCON_PIO_INV_DI |
/* Enables digital function */
IOCON_PIO_DIGITAL_EN |
/* Open drain is disabled */
IOCON_PIO_OPENDRAIN_DI);

IOCON_PinMuxSet(IOCON, 1U, 9U, port1_pin9_config);

can anyone show a demo on LPC55S69? or fingure out what's wrong in demo2.

Re: LPC55S69 Ctimer2 CAP doesn't work

RaRo — Mon, 02 Jan 2023 19:40:20 GMT

Hello @qingyunliu,

Demo 2 is using MCUXpresso IDE's ConfigTools, to use and routing the pin INPUTCAPTURE0; updating the code trough ConfigTools gives the following code:

if (Chip_GetVersion()==1)

{

IOCON->PIO[1][9] = ((IOCON->PIO[1][9] &

/* Mask bits to zero which are setting */

(~(IOCON_PIO_FUNC_MASK | IOCON_PIO_DIGIMODE_MASK)))

/* Selects pin function.

* : PORT19 (pin 10) is configured as CT_INP4. */

| IOCON_PIO_FUNC(PIO1_9_FUNC_ALT3)

/* Select Digital mode.

* : Enable Digital mode.

* Digital input is enabled. */

| IOCON_PIO_DIGIMODE(PIO1_9_DIGIMODE_DIGITAL));

}

else

{

IOCON->PIO[1][9] = ((IOCON->PIO[1][9] &

/* Mask bits to zero which are setting */

(~(IOCON_PIO_FUNC_MASK | IOCON_PIO_DIGIMODE_MASK)))

/* Selects pin function.

* : PORT19 (pin 10) is configured as CT_INP4. */

| IOCON_PIO_FUNC(PIO1_9_FUNC_ALT3)

/* Select Digital mode.

* : Enable Digital mode.

* Digital input is enabled. */

| IOCON_PIO_DIGIMODE(PIO1_9_DIGIMODE_DIGITAL));

}

Could you please try out modifying your pin_mux.c with the previous code?

Do not forget to modify the pin_mux.h with:

#define PIO1_9_DIGIMODE_DIGITAL 0x01u

#define PIO1_9_FUNC_ALT3 0x03u

If you are using MCUXpresso IDE, you could try using ConfigTools to do the same routing scheme than Demo 2, as follows:

Click in Pins icon

Search for the pin you are looking for

Check the box and select the functionality you need.

Update the Code (it will update pin_mux.c and pin_mux.h)

Best regards, Raul.

LPC MicrocontrollersのトピックLPC55S69 Ctimer2 CAP doesn't work

LPC55S69 Ctimer2 CAP doesn't work

Re: LPC55S69 Ctimer2 CAP doesn't work