topic Re: MKE04 in LPC Microcontrollers

MKE04

TEMCEFF — Fri, 14 Feb 2020 11:54:43 GMT

We are using Periodic Interrupt Timer in MKE04Z8VTG4 controller. While using PIT, facing a problem like, generating interrupt without reaching count to zero. Initializations are provided below:

void pit_init()
{

CLOCK_EnableClock(kCLOCK_Pit0);
PIT->MCR = 0x01; // Enable clock for PIT
PIT->CHANNEL[0].LDVAL = 0x0003A9A6;

PIT->CHANNEL[0].TCTRL = 0x03; // Start Timer & Interrupt Enable
NVIC_EnableIRQ(PIT_CH0_IRQn);
NVIC_SetPriority(PIT_CH0_IRQn,0);

}

Re: MKE04

Alexis_A — Mon, 17 Feb 2020 15:47:04 GMT

Hi Muralidhar M,

In the MCR register, the first bit that should be enabled is the MDIS.

Also, I will suggest to start the timer after the NVIC interruptions are enabled.

I hope this helps you.

Best Regards,

Alexis Andalon

Re: MKE04

TEMCEFF — Sat, 14 Mar 2020 07:19:02 GMT

I have done the same thing sir.

but entering into PIT Handler even if counter is not set to zero.

Even the timing is also getting mismatch. from below calculation it should be 10msec, but it is set to 13msec.

Here BUS_CLOCK = 24MHz, PIT_INT = 10msec

void pit_init()
{
pit_config.enableRunInDebug = false;

PIT_Init(PIT, &pit_config);   // PIT PERIPHERAL RUNS ON BUS CLOCK, AS PER USER MANUAL

PIT->MCR              = 0x00;                            // Enable clock for PIT
PIT->CHANNEL[0].LDVAL = 240000;//(BUS_CLOCK*(PIT_INT/1000));      // LOAD VALUE FOR EVERY 10MSEC INTERRUPT
PIT->CHANNEL[0].TCTRL = 0x03;                            // Start Timer & Interrupt Enable
NVIC_EnableIRQ(PIT_CH0_IRQn);
NVIC_SetPriority(PIT_CH0_IRQn,0);

}

void PIT_CH0_IRQHandler()
{
PIT->CHANNEL[0].TFLG = 0x01;      // Disable Interrupt
PIT->CHANNEL[0].TCTRL = 0x00;     // Disable timer & Stop timer
PIT->CHANNEL[0].TCTRL = 0x03;       // Start Timer & Interrupt Enable

count_l++;

if(count_l >= LED_TOGGLE_VALUE)
{
  flag = flag^1;
    GPIO_PortToggle(kGPIO_PORTB, 0x20); // toggle led for every 500msec
   count_l = RESET;
}
ADC_SetChannelConfig(ADC,&sADC_Config_1);
}

Please reply back..

Re: MKE04

Alexis_A — Tue, 17 Mar 2020 19:34:45 GMT

Hello Muralidhar,

In the following link if you download the SDK for the FRDM-KE06 (the SDK for the KE04 doesn't have examples available but the ones from the KE06 works for all the KE0x) you can find an example of how to configure the PIT timer.

Let me know if this helps you.

Best Regards,

Alexis Andalon

Re: MKE04

TEMCEFF — Sat, 21 Mar 2020 10:39:11 GMT

Thank you Alexis Andalon, for your valuable replies..

The link was helpful.