LPC MicrocontrollersのトピックRe: Flash programming failure for full sized binaries with LPC804

Flash programming failure for full sized binaries with LPC804

thillaielayaraj — Wed, 29 May 2019 14:51:00 GMT

Hello,

While programming the last page of LPC80x, we encounter issue. Tried both on MCUXpresso and FlashMagic. Attached the screenshots and test binaries used. Any clue on what could go wrong?

Thanks.

Re: Flash programming failure for full sized binaries with LPC804

FelipeGarcia — Thu, 30 May 2019 20:19:29 GMT

Hi,

Page 510 and page 511 in sector 31 are not available for user code because of the boot block.

Please check User Manual in chapter 4.3.5.

Have a great day,
Felipe

-------------------------------------------------------------------------------
Note:
- If this post answers your question, please click the "Mark Correct" button. Thank you!

- We are following threads for 7 weeks after the last post, later replies are ignored
Please open a new thread and refer to the closed one, if you have a related question at a later point in time.
-------------------------------------------------------------------------------

Re: Flash programming failure for full sized binaries with LPC804

thillaielayaraj — Tue, 04 Jun 2019 13:52:41 GMT

Hi,

Thanks for the information.

We created a test binary of size being 0x7E01, which means not occupying page 510 & 511, but still saw the failure with Flash magic.
Could be the drivers attempt to erase the complete sector 31 (which is not possible as per Section 4.5.10)?

Wish you a great day.

Re: Flash programming failure for full sized binaries with LPC804

FelipeGarcia — Tue, 04 Jun 2019 22:33:09 GMT

Hello,

- Do you have the same issue in MCUXpresso?

- What erase blocks are you selecting in Flash Magic?

- Could you please show me a snippet of the error your having?

Regards,

Felipe

Re: Flash programming failure for full sized binaries with LPC804

thillaielayaraj — Wed, 05 Jun 2019 04:33:18 GMT

Hi,

Here are the answers to the questions:

- Do you have the same issue in MCUXpresso?

=> No issue with MCUXpresso while programming. But,

after programming the attached dummy file (size being 0x7E01) through SWD (MCUXpresso), the device becomes not detectable through ISP (Flash Magic).
then if mass erase through SWD is performed, it gets detected via ISP.

- What erase blocks are you selecting in Flash Magic?

=> In Flash Magic, used "Sectors used by file" option

there is an option to erase "pages" via the ISP menu, but whenever starting to program the attached test file, I get a pop-up window saying "LPC804M101JHI33 (LPC800) The system cannot find the file specified"

- Could you please show me a snippet of the error your having?

=> attached.

Thanks and regards.

Re: Flash programming failure for full sized binaries with LPC804

FelipeGarcia — Thu, 06 Jun 2019 20:18:22 GMT

Hi,

Could you please try by installing the latest firmware. Try to follow the below document.

https://community.nxp.com/docs/DOC-335453

I hope it helps!

Best regards,

Felipe

Re: Flash programming failure for full sized binaries with LPC804

thillaielayaraj — Fri, 07 Jun 2019 19:35:59 GMT

Hi, it seems the link is unauthorized or does not exist. Kindly let me know. Thanks!

Regards

Re: Flash programming failure for full sized binaries with LPC804

FelipeGarcia — Mon, 10 Jun 2019 16:42:43 GMT

Hi,

I updated the link.

Regards,

Felipe

Re: Flash programming failure for full sized binaries with LPC804

thillaielayaraj — Fri, 21 Jun 2019 06:32:49 GMT

Hi, we are using LPC LINK2 Debug probe which is based on LPC4370. In this case, is the information on LPC11U35 still valid?

Re: Flash programming failure for full sized binaries with LPC804

FelipeGarcia — Mon, 24 Jun 2019 13:41:09 GMT

Hello,

Are you using a custom board?

Regards,

Felipe