LPC Microcontrollers中的主题 Re: LPC4337 USB CDC VCOM not enumerating

LPC4337 USB CDC VCOM not enumerating

rishitborad — Tue, 06 Jun 2017 14:28:51 GMT

Hi,

I am working on LPC4337 USB CDC VCOM on a customize board. It uses external crystal for clocking of 10MHz. For the software I am referring to LPCOpen usbd_rom_cdc_vcom project. Unfortunately my board doesn't support debugger yet and I am using UART printing to determine whats going on.

So far, USBD_API->hw->init() and vcom_init() returns LPC_OK. USB interrupts are being generated and program enters EP0_patch; I am also reading USBSTS register in side usb0_IRQhandler() and 'event' parameter in EP0_patch. My serial terminal outputs something like this after USBD_API->hw->Connect(g_hUsb, 1) function call :

1) USBSTS: 0x180 (SOF | SUSPENDED)

2) USBSTS: 0xC0 (SOF | RESET)

3) USBSTS: 0x84 (SOF | PORTCHANGE)

4) USBSTS: 0x81 (SOF | USBERROR)

5) EP0_patch event: USB_EVT_SETUP

6) USBSTS: 0x10001 (SOF | NAK_INT)

7) EP0_patch event: USB_EVT_OUT_NAK

8) USBSTS: 0x1 (USBERROR)

9) EP0_patch event: USB_EVT_OUT

10) USBSTS: 0x81 (SOF | USBERROR)

11) EP0_patch event: USB_EVT_SETUP

12) USBSTS: 0x1 (USBERROR)

13) USBSTS: 0x81 (SOF | USBERROR)

14) EP0_patch event: USB_EVT_SETUP

14) EP0_patch event: USB_EVT_OUT_NAK

16) USBSTS: 0x1 (USBERROR)

14) EP0_patch event: USB_EVT_OUT

15) Stops printing on serial terminal and windows reports, after a delay of 45-50 seconds, Unknown USB Device (Device Descriptor Request Failed) Code 43.

I am also setting the M-divider value to 0x071A7FAA (corrosponding to 10 MHz) in usbPLLSetup. My code is same as LPCOpen CDC_VCOM software except I had to port it to C++.

I am stuck here and hoping to get an idea of what is happening inside, the cause or resolution of the problem.

Thanks in advance,

Rishit

Re: LPC4337 USB CDC VCOM not enumerating

rishitborad — Tue, 06 Jun 2017 19:34:24 GMT

Small correction, its USB INT not USBERR.

Re: LPC4337 USB CDC VCOM not enumerating

jeremyzhou — Wed, 07 Jun 2017 01:54:31 GMT

Hi Rishit Borad ，

Thank you for your interest in NXP Semiconductor products and

the opportunity to serve you.

I'd highly recommend you to use the UsbTreeView to grab enumeration information and the tool will exemplify the issue visually, so please check the attachment.

Have a great day,
TIC

-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------

Re: LPC4337 USB CDC VCOM not enumerating

rishitborad — Wed, 07 Jun 2017 17:24:58 GMT

Resolved this problem. Turns out too many print statements caused problem.

Now i am stuck at a problem identicle to this https://community.nxp.com/thread/419944 .

Can you help?

Regards,

Rishit