LPC MicrocontrollersのトピックRe: need help with Can module https://community.nxp.com/t5/LPC-Microcontrollers/need-help-with-Can-module/m-p/546640#M13299 <HTML><HEAD></HEAD><BODY><STRONG>Content originally posted in LPCWare by xianghuiwang on Tue Dec 02 14:15:56 MST 2014</STRONG><BR /><SPAN>Hi, Mary,</SPAN><BR /><SPAN>Have you tried to run the sample project periph_can? and use it as a reference to setup your software?</SPAN><BR /><SPAN><A class="jive-link-external-small" href="https://community.nxp.com/external-link.jspa?url=http%3A%2F%2Fwww.lpcware.com%2Fcontent%2Fnxpfile%2Flpcopen-software-development-platform-lpc40xx-packages" rel="nofollow" target="_blank">http://www.lpcware.com/content/nxpfile/lpcopen-software-development-platform-lpc40xx-packages</A></SPAN><BR /><BR /><SPAN>Thanks,</SPAN><BR /></BODY></HTML> Wed, 15 Jun 2016 18:32:07 GMT lpcware 2016-06-15T18:32:07Z need help with Can module https://community.nxp.com/t5/LPC-Microcontrollers/need-help-with-Can-module/m-p/546639#M13298 <HTML><HEAD></HEAD><BODY><STRONG>Content originally posted in LPCWare by Mary Cilna on Wed Nov 12 23:46:26 MST 2014</STRONG><BR /><SPAN>hi,</SPAN><BR /><SPAN>i have configured my Can 2.&nbsp; i dont have enough knowledge to configure the bus timing registers.</SPAN><BR /><SPAN> i want to communicate with bus bit rate of 1 Mbps. what should be my baud rate ? the can module works with a clock of 60 MHz. Is it possible to establish&nbsp; the communication with this clock frequency ?</SPAN><BR /><BR /><SPAN>when the Can_Send_msg() function is called the Transmission Complete Status bit is set to '0' and am not able to receive any data in the receiving end . it happened to repeat with all the transmit buffers. why is it so ? i am new to CAN also .</SPAN><BR /><BR /></BODY></HTML> Wed, 15 Jun 2016 18:32:05 GMT https://community.nxp.com/t5/LPC-Microcontrollers/need-help-with-Can-module/m-p/546639#M13298 lpcware 2016-06-15T18:32:05Z Re: need help with Can module https://community.nxp.com/t5/LPC-Microcontrollers/need-help-with-Can-module/m-p/546640#M13299 <HTML><HEAD></HEAD><BODY><STRONG>Content originally posted in LPCWare by xianghuiwang on Tue Dec 02 14:15:56 MST 2014</STRONG><BR /><SPAN>Hi, Mary,</SPAN><BR /><SPAN>Have you tried to run the sample project periph_can? and use it as a reference to setup your software?</SPAN><BR /><SPAN><A class="jive-link-external-small" href="https://community.nxp.com/external-link.jspa?url=http%3A%2F%2Fwww.lpcware.com%2Fcontent%2Fnxpfile%2Flpcopen-software-development-platform-lpc40xx-packages" rel="nofollow" target="_blank">http://www.lpcware.com/content/nxpfile/lpcopen-software-development-platform-lpc40xx-packages</A></SPAN><BR /><BR /><SPAN>Thanks,</SPAN><BR /></BODY></HTML> Wed, 15 Jun 2016 18:32:07 GMT https://community.nxp.com/t5/LPC-Microcontrollers/need-help-with-Can-module/m-p/546640#M13299 lpcware 2016-06-15T18:32:07Z