topic Re: Compile error using KDS - Interrupt/Exception in Kinetis Design Studio

Compile error using KDS - Interrupt/Exception

Donsnook — Fri, 05 Dec 2014 20:35:52 GMT

15:26:38 **** Incremental Build of configuration Debug for project Peak ****

make -k pre-build main-build

make: Interrupt/Exception caught (code = 0xc0000005, addr = 0x00411244)

15:26:39 Build Finished (took 170ms)

Re: Compile error using KDS - Interrupt/Exception

Alice_Yang — Mon, 08 Dec 2014 01:17:33 GMT

Hello Don,

Please tell us your project in detailed , which chip ? And bareboard ? with PE ? SDK?

Then we can help you as soon as possible .

Best Regards

Alice

Re: Compile error using KDS - Interrupt/Exception

Donsnook — Mon, 08 Dec 2014 15:44:03 GMT

I'm using K22 freedom board, I have the USB setup as a CDC device, RTC enabled I'm working on setting up the SPI with DMA when I started seeing this. The first time I close SDK restarted was ok for a while. It starting happen again rebooted PC still had issues close out some other programs that I run on PC and was able to compile.

Re: Compile error using KDS - Interrupt/Exception

Alice_Yang — Tue, 09 Dec 2014 01:53:01 GMT

Hi Don,

Under the SDK, there is a "dspi_edma_demo" (C:\Freescale\KSDK_1.0.0\demos\dspi_edma_demo\kds), you can refer to this .

First run this demo on you board , then compare it with your project .

Wish it helps you!
If you still have question, please contact me!

Alice

Re: Compile error using KDS - Interrupt/Exception

Donsnook — Wed, 10 Dec 2014 23:07:06 GMT

another strange issue unable to debug k22 freedom board or CDI hardware board base on K22 freedom

loading programming algorithm ...

Done.

CMD>PM

Programming.

Processing Object File Data ...

Programmed.

CMD>VC

Verifying object file CRC-16 to device ranges ...

block 00000000-0000040F ...

block 00000420-00019B0F ...

Checksum Verification Successful. (Cumulative CRC-16=$AD31)

CMD>RE

Initializing.

Target has been RESET and is active.

Disconnected from "127.0.0.1" via 127.0.0.1

Terminating Gracefully...

Target Disconnected.

Re: Compile error using KDS - Interrupt/Exception

Alice_Yang — Thu, 11 Dec 2014 05:51:03 GMT

Hi Don,

Do you debug refer to the "kds_user_guide.pdf"-> 4.2 Debugging with the Kinetis Design Studio IDE ? (C:\Freescale\KDS_1.1.1\doc\pdf)

If you still have question, please contact us!

Best Regards

Alice

Re: Compile error using KDS - Interrupt/Exception

BlackNight — Thu, 11 Dec 2014 06:24:21 GMT

Hi Don,

can you check if you have any breakpoints or expressions/watchpoints set?

See http://mcuoneclipse.com/2014/10/11/failed-to-debug-with-gdb-breakpoints-or-expressions-on-non-existing-locations/

I hope this helps,

Erich

Re: Compile error using KDS - Interrupt/Exception

Donsnook — Thu, 11 Dec 2014 14:40:50 GMT

Erich,

I had break points but all were uncheck what I had to do is delete all break points

thanks

Re: Compile error using KDS - Interrupt/Exception

BlackNight — Thu, 11 Dec 2014 15:59:26 GMT

Yes, you have to delete them. Unchecking seems not be enough.

Erich