Kinetis MicrocontrollersのトピックRe: FRDM-K64F PIT on different Rev boards

FRDM-K64F PIT on different Rev boards

ve3id — Mon, 21 Sep 2026 17:27:48 GMT

Hi,

I am experimenting with radio networking using six FRDM-K64F boards equipped with nrf23l01 transceivers.

I am splitting a second into ten time slots, the idea being that a transmission in slot 1 gets repeated in time slot 2, time slot 2 into time slot 3 etc for relaying.

So I am using PIT to generate interrupts at 100 ms periods, which I have checked on a scope.

On three boards, rev C,F, and F this is working fine and I am seeing the data on air being repeated. However with the three rev F1 boards my transmit routine gets hung waiting for time slot 1 to come around. I am not getting the interrupt!

Does anybody know what changed between, say rev F and Rev F1 that would cause this behaviour?

Here is my init routine:

SIM->SCGC6 |= SIM_SCGC6_PIT_MASK; // Turn on clock to to the PIT PIT->MCR = 0x1; // Enable PIT timers

PIT->CHANNEL[0].LDVAL = 5999999; // Set reload value to 100mS

PIT->CHANNEL[0].TCTRL = 0x03; // Turn PIT timer 0 on, interrupts on

and in main:

NVIC_EnableIRQ(PIT0_IRQn); // Enable PI timer, ch 0 interrupt

and the ISR:

void PIT0_IRQHandler(void)

{

/* Clear interrupt flag */

PIT->CHANNEL[0].TFLG = PIT_TFLG_TIF_MASK;

NVIC_ClearPendingIRQ(PIT0_IRQn); // Clear pending PI timer, ch 0 interrupt

//scope_trigger();

time_slot +=1;

if (time_slot >10) time_slot=0;

__DSB(); // Add for ARM errata 838869, affects Cortex-M4

}

any help appreciated!

cheers

nigel

Re: FRDM-K64F PIT on different Rev boards

carlos_o — Mon, 21 Sep 2026 22:34:29 GMT

Hi @ve3id

Thank you for your post!

Please review if the errata e7914 applies for your MCU: Kinetis_K_1N83J.pdf

I've tested it in FRDM-K64F REV F1 and it works, I used SDK 2.11.0 and MCUXpresso IDE 25.06.

Also, I notice that in the code you share the "PIT->MCR = 0x1;" is included as a comment in the enablement of the SCGC6, I only want to confirm if that is a typo in the post

Re: FRDM-K64F PIT on different Rev boards

ve3id — Mon, 21 Sep 2026 23:09:36 GMT

Aha! Thanks for that. Yes I have that mask on all three chips. I'm surprised that your AI engine that I have found very useful so far did not bring that up! Is there a suggested work-around? A delay or nops maybe? And yes, the PIT->MCR = 0x1; should be on a separate line, the <cr><lf> must have have slipped out during cut and paste.

Re: FRDM-K64F PIT on different Rev boards

ve3id — Tue, 22 Sep 2026 12:34:59 GMT

I've changed my init code to this and still have the same problem:
delay(10);
volatile uint32_t PIT_MCR_read = PIT->MCR; // to overcome problem in 1N83J mask set errata 2026-09-22 NWJ
PIT->MCR = 0x1; // Enable PIT timers
PIT->CHANNEL[0].LDVAL = 5999999; // Set reload value to 100mS
PIT->CHANNEL[0].TCTRL = 0x03; // Turn PIT timer 0 on, interrupts on

Re: FRDM-K64F PIT on different Rev boards

ve3id — Tue, 22 Sep 2026 12:37:40 GMT

I even changed the delay to 100 us and still no PIT action

Re: FRDM-K64F PIT on different Rev boards

carlos_o — Tue, 22 Sep 2026 17:02:10 GMT

Hi @ve3id

The workaround mentioned with the errata is to put a read of the PIT_MCR register before writing it.

I use the PIT example of the SDK as base to test what you are doing in a FRDM board REV F1, I modified as following

It works without issues.