topic Re: External Crystal Drive Level Too High S9KEAZN64AMLC in Kinetis Microcontrollers

External Crystal Drive Level Too High S9KEAZN64AMLC

amitsinhaEM — Thu, 21 Aug 2025 12:05:04 GMT

Hello,

We are using the MCU S9KEAZN64AMLC in our design with an external crystal (ECS-160-12-37BQ-CTN-TR, load capacitance 12 pF).

We observed that the crystal drive level is about three times the recommended 100 µW.

Currently, we are using HGO = 1 (high gain) in our code because the ESR of the external crystal is 150 Ω.

Could you please advise which setup is correct, high gain (HGO = 1) or switch to low gain (HGO = 0) for this crystal?

If HGO=1 is correct why drive level of crystal too high?

Re: External Crystal Drive Level Too High S9KEAZN64AMLC

Pablo_Ramos — Tue, 26 Aug 2025 20:44:08 GMT

Hi @amitsinhaEM,

According to the datasheet, and given the crystal's ESR of 150 Ω, your setup should be configured with High Range and High Gain Mode.

Set the oscillator control register as follows:

OSC_CR[RANGE] = 1 (High frequency range)

OSC_CR[HGO] = 1 (High gain mode)

Please ensure that both the RANGE and HGO bits in the OSC_CR register are properly set.

Best Regards,

Pablo

Re: External Crystal Drive Level Too High S9KEAZN64AMLC

amitsinhaEM — Wed, 27 Aug 2025 05:12:47 GMT

We are using the same setup still drive level is too high.

Re: External Crystal Drive Level Too High S9KEAZN64AMLC

amitsinhaEM — Thu, 28 Aug 2025 05:29:48 GMT

Hi @Pablo_Ramos,

We are using the same setup still drive level is too high.

OSC_CR[RANGE] = 1 (High frequency range)

OSC_CR[HGO] = 1 (High gain mode)

Re: External Crystal Drive Level Too High S9KEAZN64AMLC

Pablo_Ramos — Mon, 08 Sep 2025 22:11:06 GMT

Hi @amitsinhaEM,

Can you help me with the following test?

Start with HGO = 0 (low-gain mode) and test for stability. If the oscillator fails to start or shows instability, switch to HGO = 1.

Best Regards,

Pablo

Re: External Crystal Drive Level Too High S9KEAZN64AMLC

amitsinhaEM — Tue, 09 Sep 2025 07:08:26 GMT

Hi @Pablo_Ramos in both the cases crystal is stable and working fine. Only difference is in case of HGO=1 drive level is too high and in case of HGO=0 drive level is withing the recommended limit. ESR of external crystal is 150 Ohm.

Re: External Crystal Drive Level Too High S9KEAZN64AMLC

Pablo_Ramos — Tue, 09 Sep 2025 16:38:05 GMT

Hi @amitsinhaEM,

What may be happening is that when the configuration is set to high-gain mode (HGO = 1), the crystal is being overdriven, as you can observe.

If the crystal operates stably in low-gain mode (HGO = 0), please use that configuration.

Best Regards,

Pablo

Re: External Crystal Drive Level Too High S9KEAZN64AMLC

amitsinhaEM — Wed, 10 Sep 2025 07:35:16 GMT

Thanks, but what is the correct way to choose drive level?

Re: External Crystal Drive Level Too High S9KEAZN64AMLC

Pablo_Ramos — Thu, 11 Sep 2025 18:07:32 GMT

Hi @amitsinhaEM,

For Drive Level evaluation, it is advisable to collaborate closely with the crystal supplier and consider utilizing the circuit evaluation services they typically offer.

Best Regards,

Pablo

Re: External Crystal Drive Level Too High S9KEAZN64AMLC

amitsinhaEM — Fri, 12 Sep 2025 06:21:01 GMT

@Pablo_RamosSo, does this mean there is no standard method to define the drive level after selecting the external crystal, and that we need to send the board to the crystal manufacturer for circuit evaluation?

Re: External Crystal Drive Level Too High S9KEAZN64AMLC

Pablo_Ramos — Fri, 17 Oct 2025 21:40:55 GMT

Hello,

I apologize for the delay; I was not able to locate any other information available on the request to share.

I apologize for the inconvenience this might cause you.

Regards,

Pablo

Re: External Crystal Drive Level Too High S9KEAZN64AMLC

amitsinhaEM — Mon, 20 Oct 2025 12:26:43 GMT

Thanks