Kinetis Microcontrollers中的主题 Re: k20 secured and unsecuring failed

k20 secured and unsecuring failed

jame — Wed, 09 May 2012 13:05:31 GMT

hi,i have two pcs of k20,one is ok,the other is bad,when i download program into it.the iar always says"timeout while unsecuing device"

how to solove the problem?

Re: k20 secured and unsecuring failed

jame — Wed, 09 May 2012 15:12:33 GMT

and i use the erase_all_pin.jlk to solve it,it also can't unsecuring it.it always say "timeout"....

Re: k20 secured and unsecuring failed

LuisCasado — Wed, 09 May 2012 23:12:57 GMT

Hi Jame,

Try the following:

1. Power off the board

2. Assert the reset pin and hold it asserted for the remainder of the process.

3. Power on the board

4. Execute “jlink.exe erase_all_pin.jlk” .

6. Release the reset pin

7. Try to connect debugger

Best Regards,

Luis

Re: k20 secured and unsecuring failed

jame — Thu, 10 May 2012 07:56:21 GMT

i follow it ,but it' s still says "timeout..."

Re: k20 secured and unsecuring failed

LuisCasado — Thu, 10 May 2012 19:40:41 GMT

Hello,

Can you post here the “jlink.exe erase_all_pin.jlk” command output? with the reset asserted.

Best Regards,

Luis

Re: k20 secured and unsecuring failed

jame — Thu, 10 May 2012 21:48:38 GMT

hi,please see attached.i'm waitting for you

Re: k20 secured and unsecuring failed

J2MEJediMaster — Fri, 11 May 2012 19:53:10 GMT

At the start of this thread, you said that you had two boards, one which worked, and one which didn't. If the boards are identical, set them side by side and compare them. Are all of the board jumpers the same? Is there any loose or bent components on the problem board? If jumpers match and there's nothing physically wrong with of the problem board, it might be some sort of hardware failure in a component.

---Tom

Re: k20 secured and unsecuring failed

jame — Sat, 12 May 2012 08:05:57 GMT

yes.i already compared these two boards and everything is the same.

i think the problem must be caused by MCU.Maybe the mcu was broken by us,maybe the mcu just has the problem.

Re: k20 secured and unsecuring failed

LuisCasado — Sat, 12 May 2012 16:57:49 GMT

Please,

Post the complete printout of the script.

Which K20? 50, 72, 100Mhz?

Best Regards,

Luis

Re: k20 secured and unsecuring failed

jame — Sat, 12 May 2012 21:29:29 GMT

it's pk20dx256vll7

Re: k20 secured and unsecuring failed

jame — Sat, 12 May 2012 22:14:51 GMT

by the way,you answer is too slow.

Re: k20 secured and unsecuring failed

LuisCasado — Tue, 15 May 2012 14:57:52 GMT

Hello,

This is a 72Mhz part. We really need to see the complete output of the script, the screens caps are only a portion. The part we want to see is what is being read from ap register 0.

Regards,

Luis

Re: k20 secured and unsecuring failed

jamezhou — Wed, 16 May 2012 07:22:51 GMT

hi:

attached is the .txt file for the complete script for your reference.

Re: k20 secured and unsecuring failed

DarthVader — Thu, 17 May 2012 01:03:31 GMT

I am not sure if this will work for you. I've got similar problems and it worked for me.

execute

JLink.exe, connect the k20 board and after that, while pressing the reset button type

unlock kinetis

release the reset button then.

this should unlock your board.

hope this helps.

Re: k20 secured and unsecuring failed

jamezhou — Fri, 18 May 2012 07:12:25 GMT

atteched is the complete output of script .

Re: k20 secured and unsecuring failed

admin — Fri, 18 May 2012 22:57:47 GMT

From the looks of your script, the good news is that mass-erase is enabled so you are not permanently locked out even though the security bit is enabled. The bad news is that your chip is not responding to the mass-erase command which means there is no way to recover it.

Re: k20 secured and unsecuring failed

jamezhou — Sat, 19 May 2012 07:08:37 GMT

is this final answer?

Re: k20 secured and unsecuring failed

dead_cell — Wed, 25 Jul 2012 13:25:45 GMT

I'm so sorry but which could lead to such results?

I have some trouble. I used example projects from freescale (IAR 6.30) for TWR-K20D50M.

I have updated the *.icf file after that I can not download MCU, debugger displays an error.