topic Re: Error in services launch sequence in Kinetis Microcontrollers

Error in services launch sequence

srihariprasad24 — Sat, 19 Jun 2021 06:01:10 GMT

Hai,

I am facing this error while debugging any codes(sdk example and new projects). i m using FRDM-KE16z Eval board. mke16Z64VLF4 controller. Kindly help solving.

thanks,

Hari.

Re: Error in services launch sequence

nxf56274 — Mon, 21 Jun 2021 01:37:09 GMT

Hi,

What's your debugger firmware of the board? When you plug the board to PC, do your PC show something like 'FRDM-KE16Z'. If not, hold the reset and then power on, do you see the disk like 'bootloader' or 'maintenance'

Have a great day,
TIC

-------------------------------------------------------------------------------
Note:
- If this post answers your question, please click the "Mark Correct" button. Thank you!

- We are following threads for 7 days after the last post, later replies are ignored
Please open a new thread and refer to the closed one, if you have a related question at a later point in time.
-------------------------------------------------------------------------------

Re: Error in services launch sequence

srihariprasad24 — Tue, 22 Jun 2021 04:58:42 GMT

Re: Error in services launch sequence

srihariprasad24 — Tue, 22 Jun 2021 04:59:17 GMT

Hi, cant able to find any port name or address, what may be the issue? Can anyone help solving?

Re: Error in services launch sequence

ErichStyger — Tue, 22 Jun 2021 05:09:12 GMT

Hi @srihariprasad24 ,

Does pressing the 'Refresh' button in your screenshot help? If not, then your P&E debug probe is not recognized. If you are using the FRDM board with an on-board P&E firmware: make sure you are connected to the board.

If you plugin in the board, it should show up in your device manager, potentially showing up as a device on your host. Can you show a screenshot or tell us about what you see? If using Windows 10 and if your board has an old bootloader, you need to update the bootloader, see https://mcuoneclipse.com/2014/11/01/illustrated-step-by-step-instructions-updating-the-freescale-freedom-board-firmware/ and https://mcuoneclipse.com/2018/04/10/recovering-opensda-boards-with-windows-10/

I hope this helps,

Erich

Re: Error in services launch sequence

srihariprasad24 — Tue, 22 Jun 2021 06:13:50 GMT

Hi, pressing Refresh did not help, I have attached some screenshots. 1st one is an another frdm board that is working good and 2nd one is the one with issue.

Re: Error in services launch sequence

ErichStyger — Tue, 22 Jun 2021 06:41:26 GMT

Hi @srihariprasad24 ,

is that COM5 from your board with the issue? If yes, the board is recognized but not as an P&E one.

What firmware did you load onto the K20 (if any)?

Does it show up as drive on your host? If so, the drive would show some diagnostic data.

I hope this helps,

Erich

Re: Error in services launch sequence

srihariprasad24 — Tue, 22 Jun 2021 07:14:20 GMT

FYI:

Eval board: FRDM- KE16Z

IC: KE16Z64VLF4

Software: MCUxpresso IDE

is that COM5 from your board with the issue? YES

I m loading the sdk demo examples.

No diagnostics are shown in the drive, screen shot attached

Re: Error in services launch sequence

ErichStyger — Tue, 22 Jun 2021 07:18:21 GMT

can you upload/share the content of the two files on the drive?

Erich

Re: Error in services launch sequence

srihariprasad24 — Tue, 22 Jun 2021 08:45:52 GMT

Hi, here it is

Re: Error in services launch sequence

ErichStyger — Tue, 22 Jun 2021 08:51:32 GMT

I see. So you have a DapLink (CMSIS-DAP) on your board. You need to connect to it using the LinkServer debug connection (not the P&E or Segger one).

I hope this helps,

Erich

Re: Error in services launch sequence

srihariprasad24 — Tue, 22 Jun 2021 11:58:41 GMT

Debugging completed.

Thanks,

Hari