Kinetis Microcontrollers中的主题 Re: Using the FRDM-HB2000-EVM evaluation board with a function generator https://community.nxp.com/t5/Kinetis-Microcontrollers/Using-the-FRDM-HB2000-EVM-evaluation-board-with-a-function/m-p/594812#M34883 <HTML><HEAD></HEAD><BODY><P>Hi,</P><P><SPAN class="caseEventBody"><SPAN class="caseEventRow"><SPAN class="cxfeeditemtext feeditemtext"><SPAN>For your case, did you install the SPI H-Bridge driver based on HB2000 and HB2001: </SPAN><A class="jive-link-external-small" href="https://community.nxp.com/external-link.jspa?url=http%3A%2F%2Fwww.nxp.com%2Ffiles%2Fanalo" rel="nofollow" target="_blank">http://www.nxp.com/files/analo</A><SPAN class="wbr"></SPAN>g/doc/user_guide/HB2000-HB2001<SPAN class="wbr"></SPAN>SWUG.pdf.</SPAN></SPAN></SPAN></P></BODY></HTML> Tue, 16 Aug 2016 02:08:17 GMT miduo 2016-08-16T02:08:17Z Using the FRDM-HB2000-EVM evaluation board with a function generator https://community.nxp.com/t5/Kinetis-Microcontrollers/Using-the-FRDM-HB2000-EVM-evaluation-board-with-a-function/m-p/594811#M34882 <HTML><HEAD></HEAD><BODY><P>I recently purchased the FRDM-HB2000-EVM evaluation board to use for a customer demo. On page 19 of the User's guide (Doc. #: KTFRDMHB2000EVM), it illustrates the hardware configuration for using this board with a function generator rather than the FRDM-KL25Z board and SPIGen interface. I followed the setup instructions, but am receiving a 'Status Fault' and cannot seem to figure out how to activate the output.&nbsp; </P><P></P><P>Note: I configured the board with the FRDM-KL25Z board and SPIGen interface and everything works fine. </P><P></P><P>Is there any additional documentation on configuring this board with the function generator?</P></BODY></HTML> Thu, 11 Aug 2016 17:32:16 GMT https://community.nxp.com/t5/Kinetis-Microcontrollers/Using-the-FRDM-HB2000-EVM-evaluation-board-with-a-function/m-p/594811#M34882 carterhough 2016-08-11T17:32:16Z Re: Using the FRDM-HB2000-EVM evaluation board with a function generator https://community.nxp.com/t5/Kinetis-Microcontrollers/Using-the-FRDM-HB2000-EVM-evaluation-board-with-a-function/m-p/594812#M34883 <HTML><HEAD></HEAD><BODY><P>Hi,</P><P><SPAN class="caseEventBody"><SPAN class="caseEventRow"><SPAN class="cxfeeditemtext feeditemtext"><SPAN>For your case, did you install the SPI H-Bridge driver based on HB2000 and HB2001: </SPAN><A class="jive-link-external-small" href="https://community.nxp.com/external-link.jspa?url=http%3A%2F%2Fwww.nxp.com%2Ffiles%2Fanalo" rel="nofollow" target="_blank">http://www.nxp.com/files/analo</A><SPAN class="wbr"></SPAN>g/doc/user_guide/HB2000-HB2001<SPAN class="wbr"></SPAN>SWUG.pdf.</SPAN></SPAN></SPAN></P></BODY></HTML> Tue, 16 Aug 2016 02:08:17 GMT https://community.nxp.com/t5/Kinetis-Microcontrollers/Using-the-FRDM-HB2000-EVM-evaluation-board-with-a-function/m-p/594812#M34883 miduo 2016-08-16T02:08:17Z