topic Re: MK10 interrupt reading problem in Kinetis Microcontrollers

MK10 interrupt reading problem

nikivendola — Thu, 09 Jun 2016 08:36:54 GMT

!Hello everyone,
I have a board composed of a MK10DN512VLL10 connected via UART to a Fastrax UP501 GPS module.
Main:

#define STDIO_UART1 volatile bool contr_GPS = false; volatile char GPS_buff[3000]; volatile int i=0; #ifdef STDIO_UART1 // enable GPS connector to be used as external UART connection PTC->PSOR = (1u << 1); uart_enable(1, 9600, false, true); printf("ready.\r\n"); #endif for(;;) {

if (contr_GPS)

{

	for (z=0; z<3000; z++)
	printf("%c", GPS_buff[z]);

}

}

Interrupt management:

extern volatile char GPS_buff[]; volatile char *data=GPS_buff; volatile bool contr_write = true; extern volatile bool contr_GPS; extern volatile int i; static void process_irq(uint8_t dev) { UART_Type *uart = uart_reg[dev]; //UART_Trans *buffer; if (uart->S1 & UART_S1_TDRE_MASK) { // NON C'E' NULLA PERCHE' TEORICAMENTE DOVREBBE DARE QUALCUSA DI DEFAULT } if (uart->S1 & UART_S1_RDRF_MASK) { if (i<3000){ *data++ = uart->D; i++; } else { uart->C2 &= ~UART_C2_RIE_MASK; uart->C2 &= ~UART_C2_RE_MASK; contr_GPS = true; } } }

If I remove contr_GPS and random print stuff out but meaningless symbols. Example:
? Cm? T? À "6½UùÄ? UG0? ¾m8? ËWÞÑæ +> ?? W®ÝUâ? ‡, |ù? Õ [??,? ÞÓÙú
Hz? $: bQŸZø "Å × · §ºö? † Ñ ?? ß§Äº6Ë AU ÷ Á ¢,? - ¡° Ê ú- ^ J¤ † Æ ÷? OCHA? Aini ??? 7ØU¤½ü%? Œ \ ä¼0? ¢ ñ> Ýº-ù9Tê? Æ? Y ÷ ü £

If you leave the condition contr_GPS prints nothing.

Do you have any tips or suggestions to understand or correct the mistake?

Thank you

Re: MK10 interrupt reading problem

jorge_a_vazquez — Fri, 10 Jun 2016 00:00:12 GMT

Hi nikivendola

RDRF is a flag that is set to indicate that Receive Data Register is Full. But you need to clear it so it can be set again in other interrupt. To clear RDRF, read S1 when RDRF is set and then read D.

if (uart->S1 & UART_S1_RDRF_MASK)
    {
          if (i<3000){
/* Dummy read for S1 when RDRF bit is set */
        (void)uart->S1;
/* Read received character, RDRF will be cleared */
         *data++ = uart->D;
         i++;
         }
          else
           {
           uart->C2 &= ~UART_C2_RIE_MASK;
           uart->C2 &= ~UART_C2_RE_MASK;
           contr_GPS = true;
           }
    }

Also, I don't see clear where and how your Process_irq function is called? This also could be related.

Hope this information can help you.

Best Regards

Jorge Alcala

Re: MK10 interrupt reading problem

nikivendola — Fri, 10 Jun 2016 16:15:04 GMT

Thanks for your answer

I wanted to ask one more thing. I added a breakpoint but I can not take it off. At each Debug I remove him with the double click on the breakpoint or double X but to debug later reappears.

How can I do?

Thank you and greetings

Re: MK10 interrupt reading problem

jorge_a_vazquez — Fri, 10 Jun 2016 23:14:25 GMT

Hi nikivendola

What debug interface are you using? and How this breakpoint appear in your breakpoint list? (windows>show views>Breakpoints). Could you please check the disassembly view and verify if the breakpoint appear there.

Best Regards

Jorge Alcala

Re: MK10 interrupt reading problem

nikivendola — Sat, 11 Jun 2016 06:38:57 GMT

I'm sorry but the debugging interface has been set by one of my prof. How do I know?

I made a sreenshot to show how it looks breakpoint.

Re: MK10 interrupt reading problem

nikivendola — Sat, 11 Jun 2016 06:57:36 GMT

This is useful for you?

Re: MK10 interrupt reading problem

jorge_a_vazquez — Mon, 13 Jun 2016 14:58:29 GMT

Hi nikivendola

You're using segger j-link to debug. The Breakpoint that you showed in your image is set in the startup menu configuration. You can uncheck this breakpoint in the startup tab in the debug configuration:

You can also check the following link: https://mcuoneclipse.com/2014/10/04/emulating-eclipse-run-with-debug-configuration/

Hope this could help.
Jorge Alcala

-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------