Trouble in waking up from VLLS1

varunrajarangan — Tue, 28 Apr 2015 05:57:44 GMT

Hi,

I am trying to put KL05 to VLLS1 mode. I have configured LLW_P6 /PTB4 to wake up in falling edge.

My problem is, the microcontroller is going to VLLS1 mode. But It is not waking up when I change the state of LLW_P6/PTB4 to low.

/************************************************************ This is my code *************************************************************************/

#include "derivative.h" /* include peripheral declarations */

#include "SpiComm.h"

#include "dma.h"

#include "timer.h"

#include "globals.h"

#define SET_NMI_INTERRUPT() SCB_ICSR |= SCB_ICSR_NMIPENDSET_MASK

#define PORTB_TOGGLE(n) GPIOB_PTOR = 0x0001 << (n)

#define PORTB_SET(n) GPIOB_PSOR = 0x0001 << (n)

#define PORTB_CLR(n) GPIOB_PCOR = 0x0001 << (n)

#define PORTB(n) GPIOB_PDIR & (0x01 << (n))

void InitPortB(){

SIM_BASE_PTR->SCGC5 |= 0x01 << 10; // Enable clock

PTB_BASE_PTR ->PDDR |= 0x01 << 8; // Direction : Output

PTB_BASE_PTR->PDOR = 0x01; // Initial value = 0

PORTB_BASE_PTR->PCR[8] = 0x01 << 8; // Enable MUX

PTB_BASE_PTR->PDDR &= ~(0x01 << 4); // PTB4 as input

PORTB_BASE_PTR->PCR[4] |= 0x01 << 8; // Enable MUX for PTB4

PORTB_BASE_PTR->PCR[4] |= 0x01 << 1; // Enable Pull-up/Pull-down

PORTB_BASE_PTR->PCR[4] |= 0x01 << 0; // Enable Pull-up resistor

// PORTB_BASE_PTR->PCR[4] |= 0x08 << 16; // Interrupt when logic '1'

// NVIC_BASE_PTR->ISER |= (uint32_t)(0x01 << 31);

}

void InitPortA(){

GPIOA_PDDR &= ~(0x1000);

PORTA_PCR12 &= ~(0x01 << 8);

PORTA_PCR12 |= 0x01 << 8;

PORTA_PCR12 |= 0xB0000;

((NVIC_MemMapPtr)0xE000E100)->ISER |=0x01<<30;

}

void Set_VLLS1(){

uint8_t temp1 = 0;

// Configure VLLS Mode

SMC_PMPROT = 0x02; // Allow Low Leakage Power Modes (VLPR,VLPW,VLPS,LLS)

temp1 = SMC_PMPROT; // Dummy read

SMC_PMCTRL = 0x04; // Run and Stop Mode Control (RUN,VLPR,VLPS,LLS,VLLSx)

temp1 = SMC_PMCTRL; // Dummy read

SMC_STOPCTRL = 0x01; // Select VLLS1

// Configure Wakeup source

LLWU_PE2 = 0x20; // Enable LLW_P6/PTB4 as wakeup source (Falling edge)

LLWU_ME = 0x40; // Enable LLWU Module 6

LLWU_F1 |= 0x01 << 6;

LLWU_F3 |= 0x01 << 6;

}

int main(void)

{

unsigned int count1 = 0x00;

InitPortB();

TimerInit();

SPI_Init(); //

Set_VLLS1(); // Configure sleep mode

PORTB_SET(8);

for(count1=0; count1<128; count1++){

SpiBuff[count1] = 0x0A + count1;

}

while(1){

if(TimeCount == 500){ // If count reached

TimeCount = 0; // Clear count

SCB_SCR|=SCB_SCR_SLEEPDEEP_MASK; // Enable ARM deep sleep modes

__asm("WFI"); // Go to sleep

}

if(PORTB(4)){

asm("nop");

}

return 0;

}

Did I miss something or did I do something wrong??

Please help me guys..

Thanks and regards

Varun Rajarangan

Re: Trouble in waking up from VLLS1

kerryzhou — Wed, 29 Apr 2015 03:49:06 GMT

Hi Varun Rajarangan,

Please add this code in the beginning area of your main:

if (PMC_REGSC & PMC_REGSC_ACKISO_MASK)

PMC_REGSC |= PMC_REGSC_ACKISO_MASK;

If it is still not OK, please refer to my code, find it from the attachment, I already set PTB4 rising as the VLLS1 wakeup source.

Wish it helps you!

Have a great day,

Jingjing

-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------

Re: Trouble in waking up from VLLS1

varunrajarangan — Wed, 29 Apr 2015 05:19:40 GMT

Hey Jingjing Zhou,

Thank you for your reply. I made it work by enabling the LLWU interrupt in NVIC-ISER.

I am a bit confused about what the datasheet says. It says that the NVIC is disabled in VLLS1 mode. Then what is the point in enabling the interrupt. Because if the NVIC is disabled, it should not serve any interrupts. Am I correct???

Regards

Varun Rajarangan

Re: Trouble in waking up from VLLS1

kerryzhou — Wed, 29 Apr 2015 05:39:09 GMT

Hi Varun Rajarangan,

Yes, you are right, NVIC won't run in VLLS1, so actually the LLWU interrupt is executed after wakeup reset.

Wish it helps you!

Have a great day,
Jingjing

Kinetis MicrocontrollersのトピックRe: Trouble in waking up from VLLS1

Trouble in waking up from VLLS1

Re: Trouble in waking up from VLLS1

Re: Trouble in waking up from VLLS1

Re: Trouble in waking up from VLLS1