topic Re: how to output RTCO on FRDM-KE02Z? in Kinetis Microcontrollers

how to output RTCO on FRDM-KE02Z?

jacquesnapoleon — Mon, 14 Sep 2015 07:48:16 GMT

Hello,

Can I find some test codes allowing to output RTCO on PTC5 using FRDM-KE02Z?

Thanks and best regards,

Jacques.

Re: how to output RTCO on FRDM-KE02Z?

jeremyzhou — Tue, 15 Sep 2015 07:22:46 GMT

Hi Jacques,

Please check the attachment.
Have a great day,
Ping

-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------

Re: how to output RTCO on FRDM-KE02Z?

jacquesnapoleon — Tue, 15 Sep 2015 09:35:32 GMT

Hi Jeremy,

Thanks for your reply.

I already had this kind of project taken from library.

Seems that this output RTCO coming from 1kHz LPO.

I would like to configure RTC clock gated from ICS, then controlling ICSIRCLK gate and SIM RTC/WDOG gate (refer to top of Figure 5-1 clocking diagram from RM).

The output frequency should be 32kHz.

I already tried this but this does not work up to now...

Many thanks and best regards,

Jacques.

Re: how to output RTCO on FRDM-KE02Z?

jeremyzhou — Wed, 16 Sep 2015 02:22:17 GMT

Hi Jacques,

In the demo, the 1kHz LPO as the clock source of the RTC, and it's supported to select other clock source.

I was wondering if you can tell what issue you stuck in.

Have a great day,
Ping

Re: how to output RTCO on FRDM-KE02Z?

jacquesnapoleon — Wed, 16 Sep 2015 06:20:11 GMT

Hi Jeremy,

Thanks for your reply and you help on this topic.

I already tried this but it cannot make appearing 32kHz frequency to RTCO pin.

I only want to use 32kHz IRC as an external signal to drive external components...

I modified the initial code as shown below.

In that case, I observed ~19.73kHz on RTCO pin which it supposed to be the 39,0625kHz divided by 2 (?), as if PTC5 output FTM signal (ICSFFCLK/2) instead of ICSIRCLK... However, RTC0 pin is well assigned to PTC5 in SIM_PINSEL as RTCS = 1...

Thanks and best regards,

Have a nice day!

Jacques.

int main (void)

{

uint8_t u8Ch;

ICS_ConfigType sICSConfig;

RTC_ConfigType sRTCConfig;

RTC_ConfigType *pRTCConfig = &sRTCConfig;

UART_ConfigType sConfig;

ICS_Trim(ICS_TRIM_VALUE);

LED0_Init();

LED2_Init();

/* configure RTC to 1Hz interrupt frequency */

pRTCConfig->u16ModuloValue = 0;

pRTCConfig->bRTCOut=RTC_OUTPUT_ENABLE;

pRTCConfig->bInterruptEn = RTC_INTERRUPT_ENABLE; /* enable interrupt */

pRTCConfig->bClockSource = RTC_CLKSRC_IREF; /*clock source is 1khz*/

pRTCConfig->bClockPresaler = RTC_CLK_PRESCALER_128; /*prescaler is 100*/

SIM->PINSEL |=SIM_PINSEL_RTCPS_MASK;

RTC_SetCallback(RTC_Task);

RTC_Init(pRTCConfig);

/* Enable IRCLK */

ICS->C1 |= 0x02;

/* switch clock mode from FEE to FEI */

sICSConfig.u32ClkFreq = 32; /* NOTE: use value 32 for 31.25KHz to 39.0625KHz of internal IRC */

ICS_SwitchMode(FEE,FEI, &sICSConfig);

while(1)

{

}

Re: how to output RTCO on FRDM-KE02Z?

jeremyzhou — Thu, 17 Sep 2015 02:56:56 GMT

Hi Jacques,

According to the fig 1 illustrates , you'll learn that

Fig 1

Have a great day,
Ping

Re: how to output RTCO on FRDM-KE02Z?

jacquesnapoleon — Thu, 17 Sep 2015 13:56:58 GMT

Hello Ping,

Thanks for your reply.

This could explain the frequency observed...

BTW, where this formula comes from, I did not find it in the reference manual...?

Thanks and best regards,

Jacques.

Re: how to output RTCO on FRDM-KE02Z?

jeremyzhou — Fri, 18 Sep 2015 01:42:25 GMT

Hi Jacques,

The formula is created by myself, by using this formula, I think it can help you to understand it easily.
Have a great day,
Ping