Kinetis MicrocontrollersのトピックRe: Ethernet using MQX

Ethernet using MQX

tusharm — Thu, 18 Jul 2013 11:23:48 GMT

Hello,

I working on K60 TWR, i m using Codewarrior 10.4 with MQX 4.0, I m trying to execute a simple Ethernet program with mqx 4.0 with static ip, but i m not able to execute the code for at least ping.

Code:

#include "main.h"

#if !defined(RAM_DISK_SIZE)

#error Please specify RAM_DISK_SIZE

#endif

const SHELL_COMMAND_STRUCT Shell_commands[] = {

/* MFS commands */

{ "cd", Shell_cd },

{ "copy", Shell_copy },

{ "create", Shell_create },

{ "del", Shell_del },

{ "disect", Shell_disect},

{ "dir", Shell_dir },

{ "format", Shell_format },

{ "mkdir", Shell_mkdir },

{ "pwd", Shell_pwd },

{ "read", Shell_read },

{ "ren", Shell_rename },

{ "rmdir", Shell_rmdir },

{ "type", Shell_type },

{ "write", Shell_write },

/* RTCS commands */

{ "arpadd", Shell_arpadd },

{ "arpdel", Shell_arpdel },

{ "arpdisp", Shell_arpdisp },

{ "gate", Shell_gate },

{ "gethbn", Shell_get_host_by_name },

{ "getrt", Shell_getroute },

{ "ipconfig", Shell_ipconfig },

{ "netstat", Shell_netstat },

#if RTCSCFG_ENABLE_ICMP

{ "ping", Shell_ping },

#endif

{ "telnet", Shell_Telnet_client },

{ "telnetd", Shell_Telnetd },

{ "walkrt", Shell_walkroute },

/* Add your custom shell commands here */

/* { "command_name", Your_function }, */

{ "sh", Shell_sh },

{ "help", Shell_help },

{ "?", Shell_command_list },

{ "exit", Shell_exit },

{ NULL, NULL },

};

const SHELL_COMMAND_STRUCT Telnetd_shell_commands[] = {

/* RTCS commands */

{ "exit", Shell_exit },

{ "gethbn", Shell_get_host_by_name },

{ "getrt", Shell_getroute },

{ "help", Shell_help },

{ "ipconfig", Shell_ipconfig },

{ "netstat", Shell_netstat },

{ "pause", Shell_pause },

#if RTCSCFG_ENABLE_ICMP

{ "ping", Shell_ping },

#endif

{ "telnet", Shell_Telnet_client },

{ "walkrt", Shell_walkroute },

{ "?", Shell_command_list },

{ NULL, NULL }

};

TASK_TEMPLATE_STRUCT MQX_template_list[] =

{

/* Task number, Entry point, Stack, Pri, String, Auto? */

{MAIN_TASK, Main_task, 2000, 9, "main", MQX_AUTO_START_TASK},

{0, 0, 0, 0, 0, 0, }

};

I m getting output on Hyper terminal as follows:

Ramdisk initialized to a:\

NOT A DOS DISK! You must format to continue.

Waiting for ethernet cable plug in ...

Please give me solution for this...

Thank you,

Tushar M

Re: Ethernet using MQX

LuisCasado — Thu, 18 Jul 2013 11:48:55 GMT

Hi,

have you configured the K60 clock and TWR-SER jumper settings properly?

Luis

Re: Ethernet using MQX

tusharm — Fri, 19 Jul 2013 04:30:51 GMT

Thanks for your response Luis. There was a problem with jumper setting now its working fine, but still i unable to ping and also i m getting that same Ramdisk initialization to a:..I would like to know what exactly that a: is?

Tushar M

Re: Ethernet using MQX

tusharm — Fri, 19 Jul 2013 05:27:16 GMT

hi Luis,

Can u please tell me what are all the jumper settings to be made...I m bit confused about the jumper settings..

I have K60 Evolution board.

Tushar M

Re: Ethernet using MQX

LuisCasado — Fri, 19 Jul 2013 08:04:07 GMT

Hi,

As you aren't able to communicate, please verify your are configuring ( I am not sure if you use TWR-K60N512 or TWR-K60D100

To enable Ethernet communication (use with TWR-SER): (getting started guide)

TWR-K60N512 - Jumper J6 on position 2-3 - processor clock taken from the TWR-SER board

TWR-K60D100M - Jumper J10 on position 2-3 - processor clock taken from the TWR-SER board

TWR-SER - CLK_SEL 3-4

TWR-SER - CLKIN-SEL 2-3 (processor clock is taken from PHY)

TWR-SER - ETH-CONFIG J12 9-10 to select RMII communication mode

What demo or example are you running?

Luis

Re: Ethernet using MQX

tusharm — Fri, 19 Jul 2013 08:41:11 GMT

Thank you Luis....Now its working very fine.....

Tushar M