i.MX ProcessorsのトピックiMX51 android 10.4 在suspend 時，需要對 gpio 作重新設置嗎?

iMX51 android 10.4 在suspend 時，需要對 gpio 作重新設置嗎?

vincent_rtk — Thu, 22 Nov 2012 11:05:39 GMT

在進入 suspend 模式時， (echo mem > /sys/power/state) ，

為了減少 suspend 的電流，需要對 imx51 的 gpio 作重新設置嗎？

例如：設置為 High-Z (input) mode，以減少電流消耗。

在其他的 application processor 都有類似的動作，但是在 imx51 android bsp 中沒有看到。

請問 imx51 不需要這樣作嗎？

謝謝

Translation: Subject---is it necessary to set GPIO pin to high-Z when entering Suspend mode in i.MX51 Androd 10.4?

When entering suspend mode, in order to reduce current, is it necessary to set GPIO pins? For example, set pin to High-Z (input) mode to reduce power consumption. In other application platform, it is required to do it. However, in i.MX51 bsp, it is not seen.

Does i.MX51 not need the action?

Re: iMX51 android 10.4 在suspend 時，需要對 gpio 作重新設置嗎?

xinyu_chen — Thu, 29 Oct 2020 09:35:56 GMT

Hi Vincent

Do you have 2.6.35 kernel. If so you can refer to arch/arm/mach-mx5/mx50_rdp.c.

There's a suspend enter/exit callback to do such GPIO pin configurations:

static struct mxc_pm_platform_data mx50_pm_data = {

        .suspend_enter = mx50_suspend_enter,

        .suspend_exit = mx50_suspend_exit,

};

We define a sets of iomux which you want that gpio configured, define all the pins as GPIO like:

static iomux_v3_cfg_t suspend_enter_pads[] = {

        MX50_PAD_EIM_DA0__GPIO_1_0,

        MX50_PAD_EIM_DA1__GPIO_1_1,

        MX50_PAD_EIM_DA2__GPIO_1_2,

        MX50_PAD_EIM_DA3__GPIO_1_3,

        MX50_PAD_EIM_DA4__GPIO_1_4,

In mx50_suspend_enter callback, we unset the PAD CTRL mask, and save current iomux configuration, set them all to GPIO ALT:

        for (i = 0; i < ARRAY_SIZE(suspend_enter_pads); i++) {

                suspend_exit_pads[i] = *p;

                *p &= ~MUX_PAD_CTRL_MASK;

                p++;

        }

        mxc_iomux_v3_get_multiple_pads(suspend_exit_pads,

                        ARRAY_SIZE(suspend_exit_pads));

        mxc_iomux_v3_setup_multiple_pads(suspend_enter_pads,

                        ARRAY_SIZE(suspend_enter_pads));

In mx50_suspend_exit callback, restore all the iomux configurations:

mxc_iomux_v3_setup_multiple_pads(suspend_exit_pads,

ARRAY_SIZE(suspend_exit_pads));

Re: iMX51 android 10.4 在suspend 時，需要對 gpio 作重新設置嗎?

YixingKong — Tue, 04 Dec 2012 09:08:21 GMT

vincent_rtk, if your question has been answered, please select Correct Answer so that we can close the DI.

Thanks,

Yixing

Re: iMX51 android 10.4 在suspend 時，需要對 gpio 作重新設置嗎?

YixingKong — Thu, 06 Dec 2012 06:22:50 GMT

No reply from the originator of the DI, I will mark the reply from XinyuChen as Correct Answer.

Re: iMX51 android 10.4 在suspend 時，需要對 gpio 作重新設置嗎?

vincent_rtk — Wed, 12 Dec 2012 11:28:46 GMT

Hi Yixing,

Thanks your reply, I have apply it right after I read it.

and I don't know it's necessary to set the "Correct Answer'.

Sorry for that.