i.MX Processors中的主题 Re: i.MX53 Loco Board UART RX Signal Changed

i.MX53 Loco Board UART RX Signal Changed

vidyasagartata — Fri, 01 Jan 2016 04:11:52 GMT

Dear All,

We have changed the UART Rx & Tx signal in the custom board as per iomux , UART Tx works fine and UART Rx does not work.

I am using the imx537 loco custom design and using ltib for BSP (U-boot2008-09)

Please help me resolve the issue.

Thanks,

Vidya

Re: i.MX53 Loco Board UART RX Signal Changed

igorpadykov — Sat, 02 Jan 2016 06:41:07 GMT

Hi Vidya

UART Rx line requires daisy chain setting, like

IOMUXC_FIRI_IPP_IND_RXD_SELECT_INPUT.

Porting new uart is described on Chapter 13 Registering a

New UART Driver i.MX53 System Development User’s Guide

http://www.nxp.com/files/32bit/doc/user_guide/MX53UG.pdf

Best regards

igor

-----------------------------------------------------------------------------------------------------------------------

Note: If this post answers your question, please click the Correct Answer button. Thank you!

-----------------------------------------------------------------------------------------------------------------------

Re: i.MX53 Loco Board UART RX Signal Changed

vidyasagartata — Thu, 07 Jan 2016 04:51:11 GMT

Dear Igor,

Thanks for reply.

We have RX signal in custom board like:

/* UART1 RXD */

mxc_request_iomux(MX53_PIN_ATA_DMACK, IOMUX_CONFIG_ALT3);

mxc_iomux_set_pad(MX53_PIN_ATA_DMACK, 0x1E4);

mxc_iomux_set_input(MUX_IN_UART1_IPP_UART_RXD_MUX_SELECT_INPUT, 0x3);

instead of (mxc_request_iomux(MX53_PIN_CSI0_D11, IOMUX_CONFIG_ALT2);

mxc_iomux_set_pad(MX53_PIN_CSI0_D11, 0x1E4);

mxc_iomux_set_input(MUX_IN_UART1_IPP_UART_RXD_MUX_SELECT_INPUT, 0x1); )

and TX signal like

/* UART1 TXD */

mxc_request_iomux(MX53_PIN_ATA_DIOW, IOMUX_CONFIG_ALT3);

mxc_iomux_set_pad(MX53_PIN_ATA_DIOW, 0x1E4);

instead of ( mxc_request_iomux(MX53_PIN_CSI0_D10, IOMUX_CONFIG_ALT2);

mxc_iomux_set_pad(MX53_PIN_CSI0_D10, 0x1E4); )

But Rx does not work, please help us to resolve the problem.

Thanks,

Vidya

Re: i.MX53 Loco Board UART RX Signal Changed

igorpadykov — Thu, 07 Jan 2016 05:19:10 GMT

Hi Vidya

suggest to connect jtag and check with it these

iomux registers.

~igor

Re: i.MX53 Loco Board UART RX Signal Changed

vidyasagartata — Thu, 07 Jan 2016 08:47:31 GMT

Dear Igor,

We do not have JTAG, Please suggest me part number for purchasing the JTAG.

Thanks,

Vidya

Re: i.MX53 Loco Board UART RX Signal Changed

igorpadykov — Thu, 07 Jan 2016 10:56:11 GMT

Hi Vidya

one can look at J-Link

SEGGER - The Embedded Experts for RTOS and Middleware, Debug Probes and Production Programmers

~igor