topic Re: About power consumption on MCIMX6Q-SDP with DORMANT mode. in i.MX Processors

About power consumption on MCIMX6Q-SDP with DORMANT mode.

keitanagashima — Thu, 11 Jun 2015 02:16:25 GMT

Dear All,

Hello.

We entered the MCIMX6Q-SDP to the DORMANT mode by below step.

------

BSP: L3.4.28_1.0.0

Mem (suspend to RAM)which maps to DORMANT mode.

$ echo mem > /sys/power/state

------

But, the power consumption was 200mA.

Could you give me advice why is the current consumption high so much?

Do you find which is the device consuming an electric current mainly on SABRE-board?

Best Regards,

Keita

Re: About power consumption on MCIMX6Q-SDP with DORMANT mode.

Yuri — Thu, 11 Jun 2015 06:01:40 GMT

Please check if kernel configuration supports DORMANT mode, using

section 22.1.3 (Menu Configuration Options) of “i.MX_6_Linux_Reference_Manual.pdf”

(L3.14.28)

Summary Page :

http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=IMX6_SW

Have a great day,
Yuri

-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------

Re: About power consumption on MCIMX6Q-SDP with DORMANT mode.

keitanagashima — Thu, 11 Jun 2015 07:01:30 GMT

Hi Yuri,

Thank you for your reply.

> Please check if kernel configuration supports DORMANT mode

Yes. It was already checked.

Power management options > [*] Suspend to RAM and standby

And, we have confirmed to enter the DORMANT mode by command in 1st topic.

Could you give me advice why is the current consumption high so much (about 200mA)?

Do you find which is the device consuming an electric current mainly on SABRE-board except the i.MX6 device?

Best Regards,

Keita

Re: About power consumption on MCIMX6Q-SDP with DORMANT mode.

Yuri — Thu, 11 Jun 2015 07:30:16 GMT

Does the value 200 mA relate to i.MX6 consumption ?
Do Your measure current of VDD_ARM_IN, VDD_SOC_IN only ?

Strictly speaking - in DORMANT mode - it is assumed core voltages

should be OFF (zero current).

Regards,

Yuri.

Re: About power consumption on MCIMX6Q-SDP with DORMANT mode.

keitanagashima — Thu, 11 Jun 2015 07:43:17 GMT

Dear Yuri,

Sorry for my poor question.

We measured the current consumption of whole SABRE board.

So, I consider that i.MX6 was very low power.

(i.e. The other devices are consuming. ex, DDR or Ether or etc...)

Do you find which is the device consuming current mainly on SABRE-board except the i.MX6 device?

Do you have any data?

Best Regards,

Keita

Re: About power consumption on MCIMX6Q-SDP with DORMANT mode.

Yuri — Thu, 11 Jun 2015 08:28:32 GMT

Alas - we do not have such data (about power consumption of the board, and its parts).

Regards,

Yuri.

Re: About power consumption on MCIMX6Q-SDP with DORMANT mode.

keitanagashima — Thu, 11 Jun 2015 08:31:00 GMT

Hi Yuri,

OK. Thank you very much!

Best Regards,

Keita

Re: About power consumption on MCIMX6Q-SDP with DORMANT mode.

keitanagashima — Tue, 23 Jun 2015 10:58:08 GMT

Hi Yuri,

We measured the current consumption at VDDARM_IN, VDDSOC_IN and, VDDHIGH_IN with deep sleep mode.

(BSP: L3.14.28_1.0.0, Board: MCIMX6Q-SDP)

- VDDARM_IN : (Min) 0.00mA, (Typ) 0.10mA, (Max) 2.32mA

- VDDSOC_IN : (Min) 4.01mA, (Typ) 4.99mA, (Max) 6.10mA

- VDDHIGH_IN : (Min) 5.45mA, (Typ) 6.17mA, (Max) 6.89mA

But, The value from Table 2. DSM Measurement Results in AN4509(Rev.0) is below.

- VDDARM_IN : 0mA

- VDDSOC_IN : 2.7mA

- VDDHIGH_IN : 0.5 or 1.8mA

[Question]

Why is the difference of the consumption current seen?

Best Regards,

Keita

Re: About power consumption on MCIMX6Q-SDP with DORMANT mode.

Yuri — Wed, 24 Jun 2015 05:25:50 GMT

VDDARM_IN and VDDSOC_IN are dropped to 0.9V (by asserting the PMIC_STBY_REQ).
Is it so, for Your case ?

Regards,

Yuri.

Re: About power consumption on MCIMX6Q-SDP with DORMANT mode.

keitanagashima — Thu, 25 Jun 2015 01:53:09 GMT

Dear Yuri,

Hello.

Thank you for your reply.

Our setting was 0.975V (BSP default setting).

Is this cause a difference of voltage?

Best Regards,

Keita

Re: About power consumption on MCIMX6Q-SDP with DORMANT mode.

Yuri — Wed, 01 Jul 2015 09:13:10 GMT

Originally other Linux release was used. As stated in the app note :
"For most Linux use cases, Gnome (Linux BSP version GA1209) based on Linux kernel version

3.0.35 was used. For other use cases, ER1203 and ER1205, based on Linux kernel version 3.0.15,

were used."

Regards,

Yuri.

Re: About power consumption on MCIMX6Q-SDP with DORMANT mode.

keitanagashima — Thu, 02 Jul 2015 09:32:51 GMT

OK. Thank you.

Best Regards,

Keita