i.MX Processors中的主题 Re: iMX6Q SATA performance (speed limit)

iMX6Q SATA performance (speed limit)

Androider — Mon, 30 Jun 2014 08:25:52 GMT

Hi all,

I've been testing the VAR-SOM-MX6 dev kit, and have noticed that the SATA write speed is well below what I would expect.

Both using a custom app and dding zeros to 2 separate SSD drives, I'm maxing out at around 96MB/s, less than a third of the rated speed of a SATA II interface.

Is there anything I'm missing here? I've looked through the IMX6DQAEC datasheet, and can't find anything about the read/write speed being less that 3.0 gbps. Could it be a limitation of the dev kit? Could anyone point me in the direction of the driver?

The SSDs I'm using are a 1tb Crucial M550 and a 120gb Kingston HyperX, and I'm running the Linaro Ubuntu 11.10 distro from the Variscite Wiki.

Thanks in advance.

Re: iMX6Q SATA performance (speed limit)

tonyzheng — Mon, 30 Jun 2014 09:17:23 GMT

Hi, Androider

The SATA II's theory speed is 300MB/s, but actually, it can't realize this speed because of many reasons.

I have test it on SabreSDP, its average speed is 124.6MB/s（64G Kingstone,Read) and 109.5MB/s(64G Kingstone,Write).

Re: iMX6Q SATA performance (speed limit)

alejandrolozan1 — Mon, 30 Jun 2014 16:21:03 GMT

Hi Tao,

Thanks for the information, it helped a lot to me too.

Best Regards,

Alejandro

Re: iMX6Q SATA performance (speed limit)

tonyzheng — Tue, 01 Jul 2014 02:52:38 GMT

Hi,

It is my pleasure. In addition,you can use strong IO test tools-IOZone to test your SATA speed.

Re: iMX6Q SATA performance (speed limit)

tordandersson — Wed, 25 Feb 2015 10:06:14 GMT

Hi Tao,

What is the physical limit on the iMX6 SATA interface throughput when using a fast SSD (>=480MB/s)?

In other words, what would be the maximum read and write throughput be if we could optimize all SW layers as much as possible?

Would it be possible to increase the throughput substantially from the ~120MB/s range or would we only gain small improvements (<10%)?

Best Regards,

Tord

Re: iMX6Q SATA performance (speed limit)

tonyzheng — Mon, 02 Mar 2015 07:28:30 GMT

Hi, Tord

There are many factor (SW or HW)to influence SATA performance.

Stroage device. It depends on different storage device;
CPU limilt. In general, The CPU compute speed will also influence read/write operation of SATA device;
SATA phyiscal signal quality. Good signal quality will reduce bit error rate.
Software stack complexity.
SATA IP features.
And some other factors.

So, we have no such accurate data. But you can do some tuning works on SATA device, such as modifying FIFO length, AHB burst length and so on.

Re: iMX6Q SATA performance (speed limit)

yaolinchang — Wed, 03 Jun 2015 08:25:28 GMT

Hi Tao,

Can you tell me how to modify FIFO length and AHB burst length?

Can you provide sample code for this?

Thanks,

Best Regards,

Yao

Re: iMX6Q SATA performance (speed limit)

tonyzheng — Tue, 09 Jun 2015 02:22:13 GMT

Hi, Yao

You can directly use memtool to write related registers. But it seems that this SATA IP don't provide the access to FIFO and burst size register for custom. The only register you can use is SATA_P0DMACR.