topic flashing redboot on mx27ads board in i.MX Processors https://community.nxp.com/t5/i-MX-Processors/flashing-redboot-on-mx27ads-board/m-p/164067#M4051 <HTML><HEAD></HEAD><BODY><DIV>hi,</DIV><DIV>&nbsp;</DIV><DIV>i have an imx27ads board which was working fine - redboot+linux.</DIV><DIV>after erasing the flash, i;m trying to reprogram redboot with the pre-built binary.</DIV><DIV>i get the following output on the uart, after which it hangs.</DIV><DIV>&nbsp;</DIV><DIV>++... Read from 0x07ee0000-0x07f00000 at 0xc1fe0000: .<BR />... Read from 0x07ed3000-0x07ed4000 at 0xc1fff000: .<BR />Ethernet FEC MAC address: is not set</DIV><DIV>Board Type: ADS<BR />Clock input: 32KHz<BR />Booting from [SDRAM]</DIV><DIV>FEC not connect right PHY: ID=fc1ffc</DIV><DIV>&nbsp;</DIV><DIV>&nbsp;</DIV><DIV>any ideas, suggestions ?<BR /></DIV></BODY></HTML> Thu, 15 Nov 2007 00:15:42 GMT ronj 2007-11-15T00:15:42Z flashing redboot on mx27ads board https://community.nxp.com/t5/i-MX-Processors/flashing-redboot-on-mx27ads-board/m-p/164067#M4051 <HTML><HEAD></HEAD><BODY><DIV>hi,</DIV><DIV>&nbsp;</DIV><DIV>i have an imx27ads board which was working fine - redboot+linux.</DIV><DIV>after erasing the flash, i;m trying to reprogram redboot with the pre-built binary.</DIV><DIV>i get the following output on the uart, after which it hangs.</DIV><DIV>&nbsp;</DIV><DIV>++... Read from 0x07ee0000-0x07f00000 at 0xc1fe0000: .<BR />... Read from 0x07ed3000-0x07ed4000 at 0xc1fff000: .<BR />Ethernet FEC MAC address: is not set</DIV><DIV>Board Type: ADS<BR />Clock input: 32KHz<BR />Booting from [SDRAM]</DIV><DIV>FEC not connect right PHY: ID=fc1ffc</DIV><DIV>&nbsp;</DIV><DIV>&nbsp;</DIV><DIV>any ideas, suggestions ?<BR /></DIV></BODY></HTML> Thu, 15 Nov 2007 00:15:42 GMT https://community.nxp.com/t5/i-MX-Processors/flashing-redboot-on-mx27ads-board/m-p/164067#M4051 ronj 2007-11-15T00:15:42Z Re: flashing redboot on mx27ads board https://community.nxp.com/t5/i-MX-Processors/flashing-redboot-on-mx27ads-board/m-p/164068#M4052 <HTML><HEAD></HEAD><BODY><DIV></DIV>Hi ronj,<BR /><BR />&nbsp;&nbsp; Check if you are programming the right binary that came with your ltib package (It's important considering that has many .bin versions).<BR />&nbsp;<BR />&nbsp;&nbsp; Are you adding a script to start redboot? Are you trying to boot with NFS or JFFS2 file system?<BR /><BR />&nbsp;&nbsp; Regards,<BR /><BR />Rogerio.<BR /><DIV></DIV></BODY></HTML> Wed, 08 Oct 2008 03:15:23 GMT https://community.nxp.com/t5/i-MX-Processors/flashing-redboot-on-mx27ads-board/m-p/164068#M4052 rogerio_silva 2008-10-08T03:15:23Z