i.MX ProcessorsのトピックRe: IMX6QualQuad SABRED

IMX6QualQuad SABRED

rayxianghoooo — Thu, 10 Oct 2013 08:58:48 GMT

Hi All, i'm installing and building LTIB by "i.MX 6Dual/6Quad SABRE-SD LinuxUser's Guide.pdf" , when i run "./ltib -m config" it shows :

------------------------------------------------------------------------------------------------------

For information about obtaining TeX, please see http://www.tug.org. If

you happen to be using Debian, you can get it with this command:

apt-get install tetex-bin

make[2]: *** [flex.pdf] Error 1

make[2]: Leaving directory `/opt/freescale/ltib/usr/src/rpm/BUILD/flex-2.5.37/doc'

make[1]: *** [install-recursive] Error 1

make[1]: Leaving directory `/opt/freescale/ltib/usr/src/rpm/BUILD/flex-2.5.37'

make: *** [install] Error 2

error: Bad exit status from /home/season/mx6/river/ltib/tmp/rpm-tmp.98666 (%install)

-----------------------------------------------------------------------------------------------------------------------

but when i run :sudo apt-get install tetex-bin , it's

---------------------------------------------------------------------------

Reading package lists... Done
Building dependency tree
Reading state information... Done
Some packages could not be installed. This may mean that you have
requested an impossible situation or if you are using the unstable
distribution that some required packages have not yet been created
or been moved out of Incoming.
The following information may help to resolve the situation:

The following packages have unmet dependencies:
tetex-bin: Depends: tetex-base (>= 3.0-4) but it is not going to be installed
Depends: tex-common (>= 0.34) but it is not going to be installed
E: Broken packages

---------------------------------------------------------------------------------

hoe can i fix ti?

Re: IMX6QualQuad SABRED

maurice — Thu, 10 Oct 2013 11:39:07 GMT

Hi,

If you don't need Flex package, then remove it from package list.

However, you can try to install texlive-base package: "sudo apt-get install texlive-base"

Re: IMX6QualQuad SABRED

Rita_Wang — Fri, 11 Oct 2013 02:18:59 GMT

Hi rayxiang,

You can do as maurice said, remove the Flex package and install texlive-base package by commend: $sudo apt-get install texlive $sudo apt-get install texlive-base .

By the way, are you using the newest BSP ? If not, you can have a try.

Best Regards

Dan

Re: IMX6QualQuad SABRED

rayxianghoooo — Mon, 14 Oct 2013 08:12:51 GMT

Hi, Dan
I follow the commend sudo apt-get install texlive ,but it shows:

---------------------------------------------------------------------------------------------

prosper depends on texlive-latex-base; however:

Package texlive-latex-base is not configured yet.

prosper depends on texlive-latex-recommended; however:

Package texlive-latex-recommended is not configured yet.

dpkg: error processing prosper (--configure):

dependency problems - leaving unconfigured

dpkg: dependency problems prevent configuration of texlive-humanities:

texlive-humanities depends on texlive-latex-base (>= 2007-11); however:

Package texlive-latex-base is not configured yet.

dpkg: error processing texlive-humanities (--configure):

dependency problems - leaving unconfigured

dpkg: dependency problems prevent configuration of tipa:

tipa depends on texlive-latex-base; however:

Package texlive-latex-base is not configured yet.

dpkg: error processing tipa (--configure):

dependency problems - leaving unconfigured

Errors were encountered while processing:

texlive-latex-base

texlive-latex-recommended

texlive

texlive-latex-extra

texlive-math-extra

texlive-lang-cyrillic

texlive-xetex

dblatex

latex-xcolor

pgf

latex-beamer

prosper

texlive-humanities

tipa

E: Sub-process /usr/bin/dpkg returned an error code (1)

-------------------------------------------------------------------------------------------------------

what's that supposed to mean?

Re: IMX6QualQuad SABRED

Rita_Wang — Tue, 15 Oct 2013 04:48:03 GMT

Hi rayxiang,

Sorry for the previous answer, and now I get the right solution.

When you run "./ltib -m config", error as you have mentioned above. As your BSP is L3.0.35_4.0.0_130424_source and UBUNTU is

ubuntu 12.04 x86_64

Install below package for LTIB can fix the error:

sudo apt-get install texinfo

sudo apt-get install texlive

Best Regards,

Dan

Re: IMX6QualQuad SABRED

carmilili — Tue, 15 Oct 2013 09:36:32 GMT

Hi Dan

I meet the same problem.Your reply don't not solve the problem.

Re: IMX6QualQuad SABRED

florianl — Tue, 15 Oct 2013 15:50:09 GMT

Hi Dan,

for me it's the same problem: I have everything set up like described in the last BSP Documentation. VM in VirtualBox with Ubuntu 9.04 and all package sources set up accordingly to your Document "Set Up LTIB Environment".

Then on installing prerequisites (packages as described in the Set Up Document) I get the same error messages!

Do you have a solution for this?

Thanks!

Florian

Re: IMX6QualQuad SABRED

Rita_Wang — Wed, 16 Oct 2013 02:34:20 GMT

Hi Cmrmili,

Would you please provide your environment? Thanks.

Best Regards

Dan

Re: IMX6QualQuad SABRED

carmilili — Wed, 16 Oct 2013 02:38:15 GMT

I have solved this problem.

sudo apt-get update

sudo apt-get -f install

Re: IMX6QualQuad SABRED

Rita_Wang — Wed, 16 Oct 2013 03:08:31 GMT

Hi Carmili,

After you executing the commend :

sudo apt-get update

sudo apt-get -f install

have you run these two to solved the problem

sudo apt-get install texinfo

sudo apt-get install texlive

Thanks.

Best Regards

Dan

Re: IMX6QualQuad SABRED

carmilili — Wed, 16 Oct 2013 04:03:13 GMT

Hi,Dan

It is not necessary to run the command.

sudo apt-get install texinfo

sudo apt-get install texlive

Re: IMX6QualQuad SABRED

Rita_Wang — Wed, 16 Oct 2013 04:40:35 GMT

Hi Camili,

OK. Thanks a lot.

Best Regards

Dan

Re: IMX6QualQuad SABRED

Rita_Wang — Wed, 16 Oct 2013 05:09:18 GMT

Hi Florian,

Would you mind telling me your BSP, L3.0.35_4.0.0 or L3.0.35_4.1.0 ?

You can have a try the commends:

sudo apt-get update

sudo apt-get -f install

You also can reference the documnet

i.MX Linux BSP Environment Setup

Best Regards

Dan

Re: IMX6QualQuad SABRED

florianl — Wed, 16 Oct 2013 08:12:13 GMT

Hi there,

yes I set everything up as mentioned in this document - I'm using the latest Version of the BSP (L3.0.35_4.1.0). BUT, the problem was still there and I (or better a good friend) fixed this latex time bomb: Michael Dodl - LaTeX - Disabling the 5 year time bomb

Maybe you should add this as a patch to the getting started documents!!

Re: IMX6QualQuad SABRED

Rita_Wang — Wed, 16 Oct 2013 09:10:05 GMT

Hi Florian,

OK. I will discuss with my team colleagues. Thanks.

Best Regards

Dan

Re: IMX6QualQuad SABRED

florianl — Wed, 16 Oct 2013 11:56:31 GMT

By the way: There was somebody else who had this problem: Building the LTIB in iMX6 in linux bsp

Here again some detailed informations about my setup:

I had the same problem yesterday on a fresh install of Ubuntu 9.04 - I also wanted to use the latest BSP (L3.0.35_4.1.0_ER_SOURCE_BSP).

To reproduce my setup: I did everything mentioned in the "Setting Up LTIB host" in the docs (L3.0.35_4.1.0_..._docs) Package from the Freescale site.

The problem is indeed the old latex package for Ubuntu 9.04 - you can fix it after the failed setup by commenting out some lines in /usr/share/texmf-texlive/tex/latex/base/latex.ltx and running the installation again like mentioned in your "Setting Up LTIB host" - doc:

sudo aptitude -y install asciidoc texlive-latex-base dblatex xutils-dev

For more information about the problem please read this blog entry: http://my.opera.com/Michael-Dodl/blog/2011/06/24/latex-disabling-the-5-year-time-bomb

Hopefully it helps!

Best regards

Florian

Re: IMX6QualQuad SABRED

Rita_Wang — Thu, 17 Oct 2013 02:18:51 GMT

Hi Florian,

Thanks a lot for your useful advice. It's truly due to the old packages for Ubuntu 9.04. So the best method is to update the version of UBUNTU to 10.04 or 12.04 .

Best Regards

Dan

Re: IMX6QualQuad SABRED

Rita_Wang — Thu, 17 Oct 2013 02:26:26 GMT

Hi rayxiang,

It's truly due to the old packages for Ubuntu 9.04. So the best method is to update the version of UBUNTU to 10.04 or 12.04. If you are using the newest BSP L3.0.35_4.1.0 . Then you have to set up linux environment according to the document "Setting Up LTIB host" in the docs (L3.0.35_4.1.0_..._docs).

Best Regards

Dan

Re: IMX6QualQuad SABRED

florianl — Thu, 17 Oct 2013 09:11:25 GMT

Hi Dan!

But please, please offer official support then for the newer Ubuntu releases... At the moment it is a real pain to set up ltib on a fresh install of Ubuntu 10 or 11 or 12...

Or do you have ALL necessary patches for the setup at the newer Ubuntu versions? It would be great... or would you rather recommend to use YOCTO instead?

Best regards

Florian

Re: IMX6QualQuad SABRED

LeonardoSandova — Thu, 17 Oct 2013 15:10:19 GMT

Hi Florian,

I understand your frustration. One of the reasons we are moving to Yocto is that is less host-dependant, where you just need a few packages installed and all the rest Yocto (in fact, bitbake, the core engine) fetches and compiles. I would strongly suggest to move to Yocto; there are some documents out there to smooth the ramp-up.

Leo